Scattering control using square and hexagonal checkerboard surfaces

Electromagnetic band-gap (EBG) structures have noteworthy electromagnetic characteristics that include their reflection phase variations with frequency. This paper applies this unique reflection phase property to alter the direction of the fields scattered by a radar target to reduce its radar cross section (RCS). This redirecting of the scattered fields occurs when a surface is covered with a checkerboard of alternating EBG structures, and results in a wider frequency band RCS reduction. RCS reduction compared to a PEC surface of 10 dB can be realized over 60% frequency bandwidth. Simulations of monostatic and bistatic RCSs of two dual EBG checkerboard surfaces, square and hexagonal, are compared with those of equal-sized PEC ground planes. The simulated monostatic RCS is also compared with measurements. Both TE <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">z</sup> and TM <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">z</sup> polarizations for oblique incidence are considered. Excellent agreement is obtained between simulated and measured patterns, for both the square and the hexagonal EBG checkerboard surfaces. An approximate analytical expression is provided as a guideline for a 10-dB RCS reduction of a dual EBG checkerboard surface compared to that of a PEC.

In this letter, electromagnetic band-gap (EBG) structure is used to reduce the radar cross section (RCS) of the patch array antenna. The proposition of this method is based on the high impedance characteristic of the mushroom-like EBG structure. The basic patch array antenna is designed with a central frequency of 5.0 GHz while replacing the substrate of the array with the mushroom-like EBG structure. The frequency band in which RCS of the patch array antenna reduced significantly can be adjusted by parameters of the EBG. The backward RCS of the patch array antenna with EBG can be reduced as much as 10 dB compared to that of the conventional array antenna, and the degradation of the antenna performance is not significant.

In this paper, a switchable radar cross section (RCS) reduction between the two broadbands' (1-7 GHz and 4-10 GHz) has been achieved by just considering the integration of hybrid frequency selective surface (FSS) based phase cancelation structure (PCS) with a modified ground square patch antenna operating at 2.4 GHz. The full metallic ground plane of the conventional microstrip antenna (MSA) is replaced by a 2 × 2 array of band-stop FSS having the same frequency as that of the MSA. This ground plane modification helps to increase the maximum out-of-band RCS reduction from 16.4 dB to 20 dB. The ground modified MSA without any PCS exhibits both in-band and out-of-band maximum RCS reduction of 20 dB over a wideband (1-7 GHz). A new approach is adopted to form the PCS. It is formed by placing two non-overlapping hybrid FSSs at different heights above the MSA. The MSA with FSS based ground plane along with the hybrid FSS based PCS exhibits good monostatic and bistatic RCS reduction across 4 to 10 GHz without affecting the radiation characteristics of the conventional MSA. The measured results show a close resemblance to the simulated ones.

Electromagnetic Bandgap (EBG) structures have been successfully applied for suppressing the Simultaneous Switching Noise (SSN) between the power and ground planes. Aimed at the relative narrow bandwidth and the poor performance in low frequency of the conventional Uniplanar-Compact EBG (UC-EBG) structure, a novel EBG structure formed by adding spiral-shaped metal strips on the conventional UC-EBG is proposed. This new EBG structure significantly enhance the equivalent inductance between the neighboring nuit cells, as well as change the character of the stop-band. Simulation results show that the new EBG structure can achieve a bandwidth reach 4.35GHz.This stop-band is 47.5% wider than the conventional UC-EBG structure, and 17.5% wider than the reference EBG structure in literature. The excellent SSN suppression is achieved between 0.18-4.53GHz in the depth of -40dB.

This paper proposes a reconfigured horn antenna with reduced side-lobe radiation by using electromagnetic band gap (EBG) structure. A mushroom-like structure with a circular-shaped patch as unit cell is designed to achieve a complete EBG. The EBG structure is lined on the metal wall along the E-plane of the horn antenna. This causes the surface waves on the metal wall to be suppressed, resulting in lower side-lobe emission. A conducting wedge is inserted on the gap between the EBG structure and waveguide feed aperture to achieve impedance matching in the antenna. In addition, the proposed horn antenna is suitable for high power systems due to a purely metallic construction of the EBG structure.

In this paper, we present an equivalent circuit (EC) based technique which combined with the numerical method to optimize the EBG structures with simple square-loop frequency selective surfaces (FSSs), they can take on in-phase reflection characteristic in some broad-band electromagnetic band gap (EBG) structures. By using the multilayered FSSs in this type of EBG structure, the surface waves and current could stopped effectively. The geometry and working of the antenna with this EBG structure are detailed and the design method is proposed.

Band notched circular monopole antennas for ultra-wide band applications are proposed in this paper. The proposed antennas in this paper can reject worldwide interoperability for microwave access WiMAX band (3.3–3.8 GHz) and wireless local area network WLAN band (5–6 GHz). Antennas utilises mushroom-type electromagnetic band gap (EBG) structures and I-slot embedded edge located via (ELV) EBG structures to achieve band-notched designs. The advantages of band notched designs using EBG structures like notch-frequency tuning, dual-notch antenna designs and stable radiation pattern are also verified. Various antenna designs with slot in EBG structures, variations in placement of EBG structures, number of EBG structures and ELV type EBG structures are simulated. About 30% reduction in size of EBG structures is obtained if conventional mushroom type EBG is replaced by proposed I-slot embedded ELV-EBG structure. Fabricated and measured results are in good agreement with simulated ones.

A new design method for ultrabroadband radar cross section (RCS) reduction by exploiting characteristic complementary polarization conversion metasurfaces (PCMs) is proposed and validated. The proposed method lifts the conventional bandwidth limitation enforced by the performance of a single PCM and expands the RCS reduction bandwidth. A systematic strategy for ultrabroadband RCS reduction design is developed and an effective reflection coefficient amplitude of the composite surface ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\Gamma _{ {eff}}$ </tex-math></inline-formula> ) is derived as a new RCS reduction indicator. Based on this indicator, complete polarization conversion (CPC) frequency points of PCM are identified as important characteristics, and PCM pairs with interleaved CPC points, termed as initial PCM (I-PCM) and complementary PCM (C-PCM), are designed to compensate each other for ultrabroadband RCS reduction. A scaling-and-tuning two-step method for designing the C-PCM of a specific I-PCM is developed and validated. To further improve RCS reduction performance, taking the <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${\Gamma _{ {eff}}}$ </tex-math></inline-formula> as an indicator, the particle swarm optimization (PSO) algorithm is used to select the optimal I-PCMs, C-PCMs, and their area ratios. Finally, an ultrabroadband RCS reduction surface is designed, fabricated, measured, and validated. It realizes 10-dB monostatic RCS reduction ranging from 7.6 to 26.2 GHz (110.7% relative bandwidth) which exceeds the polarization conversion bandwidth of each individual PCM. Besides, good polarization insensitivity and bistatic RCS reduction performance are also obtained. The proposed method provides a new route for designing broadband RCS reduction surface based on PCMs with unsatisfactory characteristics and greatly alleviates the performance requirement for PCMs.

Electromagnetic Bandgap (EBG) structures are increasingly utilized by a variety of microwave and optical devices as filters for unwanted signals. One such application is their incorporation in power distribution network (PDN) of electronic circuits where the EBG structure replaces one of the reference voltage planes thus forming a shielded EBG structure. The EBG induces a wide (on the order of few GHz) omni-directional stopband in the operating frequency range of the PDN which mitigates the so called simultaneous switching noise (SSN) on the power plane. The challenging aspect in designing an EBG for such applications is to achieve a wide stopband centered at low GHz frequencies while maintaining a reasonably small unit cell size and a low profile. Indeed, the dimensions of the unit cell of the EBG structure for low frequency designs can become relatively large with respect to the size of the host dielectric substrate. Therefore, availability of a systematic design approach that can provide a fast and accurate means of performance prediction to enable geometry tweaking and design optimization will be of critical importance in utilizing EBG structures in such applications.

A wideband monostatic and bistatic radar cross-section (RCS) reduction of microstrip antenna array is proposed and investigated. By using coding metasurface on the proposed antenna, the reflected energy is diffused scattering to more directions. A remarkable monostatic RCS reduction is achieved from 6 to 7.6 GHz and 9.5 to 26 GHz covering the working frequency band, and the bistatic RCS of proposed antenna is also effectively suppressed. The proposed antenna still maintains in a compact structure, while the antenna radiation performance is preserved. Both the reference and proposed antennas are fabricated and measured in anechoic chamber, and the results show that there is a good agreement between simulations and measurements.

This paper presents a circularly polarized printed circuit board (PCB) patch antenna using mushroom-like electromagnetic band gap (EBG) structure for gain enhancement. Unlike the popular method of using artificial magnetic conductor (AMC) or EBG structure as the ground of the antenna, we place the mushroom-like EBG structure around the patch antenna to avoid increasing the number of PCB layers. The EBG structure works in-phase reflection around 24.25 GHz by optimizing design. Limited by the size of the antenna, only twelve EBG units can be distributed around the corner-cut square circularly polarized patch antenna. Simulation results show that gain of the antenna enhances 0.8 dB and cross polarized gain reduces about 15 dB, moreover, the axial ratio is also improved.

For 60-GHz band communications, both the mutual coupling and transmission distance restrict the performance of a multiple-input multiple-output (MIMO) antenna array. Several studies presented different types of meta-materials and electromagnetic bandgap (EBG) structures to improve the performance of a MIMO antenna array at the 60-GHz band. In this paper, we presented the four-element MIMO patch antenna with different types of EBG structures for the millimeter wave (mmW)communications at the 60-GHz unlicensed industrial, scientific, and medical band. The single element of the MIMO antenna array covered the mmW band from 57 GHz to 63 GHz having the dimensions of 1.3 mm × 1.8 mm × 0.1 mm. We developed a set of square-shaped, cross-shaped, and complex-slotted EBG ground planes between the antenna elements for the performance improvement. All the three EBG ground planes provided significant coupling reduction between the mmW MIMO antenna elements. The proposed EBG structures exhibited wide bandgap characteristics and improved scattering parameters in the desired frequency band. In contrast with the cross- and complex-slotted, the square-shaped EBG structure substantially improved the overall gain of MIMO antenna array. In addition, the square-shaped EBG reformed the maximum beam and enhanced the far-field gain pattern in the desired direction. Experimental results conducted with the fabricated prototypes showed a good agreement with the simulation results and adequately covered the 60-GHz band. The low-profile and salient features of the proposed MIMO antenna array shows the potential for on-chip applications at 60 GHz.

In this paper, the reduction in Radar cross section (RCS) is achieved by using a checkerboard which is a composition of two different compact EBG structures. The checkerboard surface has two special EBG patterns, each located in a quadrant of the same ground plane, which can use special features of the EBG pattern to achieve a 10dB RCS reduction. The direction of scattered field can be altered by radar target to minimize the RCS. This alteration can be achieved by covering the target surface with a checkerboard of alternating EBG structures. The designed ch is engineered using Ansys High-Frequency Structure Simulator (HFSS), and the results were compared with RCS results for a perfect electrical conductor (PEC) surface.

This paper presents a design of a dielectric resonator antenna (DRA) for millimeter-wave applications. An electromagnetic band gap (EBG) structure is used in the antenna design to enhance the antenna characteristics. The simulated with and without EBG results of the designed antenna is calculated to show the parameters such as impedance bandwidth, reflection coefficient, and gain. The parameters of the proposed antenna have improved after the periodic unit cell structure (EBG) introduction. The obtained reflection coefficients of the proposed antenna with and without EBG structure are −30.5 dB and −20.8 dB, respectively. In the presence of an EBG structure antenna shows a peak gain of 25 dBi, which is higher than the without EBG (8 dBi) structure. The designed antenna resonates at 33 GHz with an impedance bandwidth of 700 MHz. The Ansys HFSS software is used to design and simulate the proposed antenna.

In this paper a novel microstrip antenna is proposed using electromagnetic band gap (EBG) structure for mobile and wireless applications. It covers two mobile bands ranging from (2.20–2.29) GHz and (2.29–2.30) GHz. An extremely compact size EBG structure is applied in a square shape. After applying EBG structure to the proposed design, performance characteristics such as percentage bandwidth and return loss enhance by 5.1% and 5% respectively. Also by changing the feed and shorting pole (via) position, the same structure is used for ISM (2.45 ± 0.05) GHz band with resonant frequency 2.45 GHz. The measured and simulated results show very good agreement. The design structure is fabricated using FR4 substrate with dielectric constant 4.4, loss tangent 0.02 and thickness 1.6 mm.