The Effect of Solid Surface Roughness on Dynamic Contact Angles in Solid-Liquid-Liquid Systems

The simplified ray-tracing technique reported in Part I of this paper is employed to compute the single-scattering properties of hexagonal columns with maximum dimensions ranging from 2 to 3500 mum with a size-bin resolution of 2 mum at wavelengths of 0.86 and 2.13 mum. For small ice crystals, the current treatment of surface roughness may not be adequate because the applicability of the principles of geometric optics breaks down for small roughness scale. However, for ice crystals smaller than 40 mum, the aspect ratios of these particles are close to one, and the effect of surface roughness is quite small. In this paper, the diffraction is accounted for in the same way as in the case of smooth particles. It is essentially unfeasible to incorporate the effect of surface roughness into the numerical computation of the diffraction contribution. The scattering properties of individual ice crystals are then averaged over 18 particle size distributions whose effective particle radii (re) range from 5 to 90 mum. The single-scattering properties of ice clouds are strongly sensitive to surface roughness condition. Lookup tables that are built for the correlation between the bidirectional reflectances at wavelengths of 0.86 and 2.13 mum with different roughness conditions are used to retrieve ice cloud optical thickness and effective particle size over oceans. Pronounced differences are noticed for the retrieved cirrus cloud optical thickness and effective particle sizes in conjunction with different surface roughness conditions. The values of the retrieved cirrus cloud optical thickness in the case of the rough surface are generally smaller than their counterparts associated with smooth surface conditions. The effect of surface roughness on the retrieved effective particle radii is not pronounced for slight and moderate roughness conditions. However, when the surfaces of ice crystals are substantially rough, the retrieved effective radii associated with roughened particles are larger and smaller than their smooth surface counterparts forlarge (re>50 mum) and small (re<35 mum) ice crystals, respectively, whereas the effect of surface roughness on the retrieved effective radii shows a nonmonotonic feature for moderate particle sizes (35 mum<re<50 mum). In general, the dominant effect of surface roughness on cloud property retrievals is to decrease the retrieved optical thickness and to increase the retrieved effective particle size in comparison with their counterparts in the case of smooth ice particles.

Fatigue behavior of additive manufactured 316L stainless steel parts: Effects of layer orientation and surface roughness

Surface roughness affects proliferation, differentiation (alkaline phosphatase and osteocalcin), local factor production (transforming growth factor (TGF beta) and prostaglandin E2 (PGE2)], and response to 1,25-(OH)2D3 (1,25) of MG63 osteoblast-like cells. In this study, we examined whether the effect of surface roughness on MG63 cells is mediated by prostaglandins produced by the cells. Unalloyed titanium (Ti) disks were pretreated with HF/HNO3 (PT) and then machined and acid-etched (MA). Disks were also coarse grit-sandblasted (SB), coarse grit-sandblasted and acid-etched (CA), or plasma-sprayed with Ti particles (PS). The surfaces, from smoothest to roughest, were PT, MA, CA, SB, and PS. MG63 cells were cultured to confluence on the Ti disks in the presence or absence of 10(-7) M indomethacin (Indo), a specific inhibitor of cyclooxygenase activity, resulting in decreased prostaglandin production. When the cells reached confluence, cell number, cell layer alkaline phosphatase specific activity (ALPase), and osteocalcin (OC) and latent TGF beta (LTGF beta) production were determined. In addition, confluent cultures which had been grown in the absence of Indo were exposed to 10(-7) M 1,25, 10(-7) M Indo, or a combination of the two for 24 h. On the rougher surfaces, cell number was decreased and ALPase, OC, and LTGF beta were increased. When indomethacin was present throughout the culture period, the effect of surface roughness on cell number, OC, and LTGF beta was abolished. ALPase was reduced, but surface roughness-dependent effects were still observed. Addition of indomethacin to confluent cultures for 24 h had no effect on any of the parameters examined, with one exception: Cells cultured on MA surfaces exhibited a more differentiated phenotype. 1,25 increased all parameters examined on SB, CA, and PS surfaces. When indomethacin was added with 1,25, the 1,25-dependent effects on cell number and OC and LTGF beta production were abolished; however, ALPase was unaffected. This indicates that bone cell response to systemic hormones may be modified by implant surface roughness. This effect may be mediated, at least in part, by prostaglandins produced by the same cells.

Effect of roughness and shape factor on flotation characteristics of glass beads

Purpose Surface properties (smooth or roughness) play a critical role in controlling the wettability, surface area and other physical and chemical properties like fluid flow behaviour over the rough and smooth surfaces. It is reported that rough surfaces are offering more significant insights as compared to smooth surfaces. The purpose of this study is to examine the effects of surface roughness in the diverging channel on physiological fluid flows. Design/methodology/approach A mathematical formulation based on the conservation of mass and momentum equations is developed to derive exact solutions for the physical quantities under the assumption of low Reynolds numbers and long wavelengths, which are appropriate for biological transport scenarios. Findings The results reveal that an increase in surface roughness reduces axial velocity and volumetric flow rate while increasing pressure distribution and turbulence in skin friction. Research limitations/implications These findings offer valuable insights for biological flow analysis, highlighting the effects of surface roughness, non-uniformity of the channel and magnetic fields. Practical implications These findings are very much applicable for designing the pumping devices for transportation of the fluids in non-uniform channels. Originality/value This study examines the impact of surface roughness on the peristaltic pumping of viscoelastic (Jeffrey) fluids in diverging channels with transverse magnetic fields.

Spontaneous imbibition in microchannels is a critical phenomenon in various industrial applications, such as enhanced oil recovery and microfluidic systems. One of the key factors influencing the imbibition process is the dynamic wetting effect, which governs the interaction between the liquid and solid surfaces. This paper improves the original pseudopotential model for interfluid forces by coupling it with the Peng-Robinson equation of state. The model's accuracy is verified through thermodynamic consistency checks, simulations of gas-liquid interfacial tensions, and testing of static equilibrium contact angles. Following model validation, we use it to simulate spontaneous gas-liquid imbibition in microchannels and investigate dynamic contact angle evolution during the process. The results demonstrate that (1) as the microchannel width increases, inertia forces become more significant during the initial imbibition stages, leading to a greater difference between the dynamic and static contact angles. (2) A decrease in fluid-solid interaction strength results in a larger gap between dynamic and static contact angles. (3) Higher interfacial tension strengthens the capillary forces, accelerating the imbibition rate and enlarging the difference between the dynamic and static contact angles. Furthermore, the dynamic contact angle data obtained from our simulations can be used to correct the traditional Lucas-Washburn equation. The corrected equation predicts imbibition distances that closely match the simulation results.

A low-frequency (3-10 MHz) scanning acoustic microscope was used to image subsurface defects in samples with rough surfaces. phase of the reflected signal was measured. By characterizing the angular spectrum of the transducer, it was possible to predict the effect of surface roughness on a defocused image from an image taken with the transducer on focus. This enabled the effects of the surface roughness to be subtracted out of the defocused image, thereby giving enhanced subsurface defect detection. Both the amplitude and

The biological properties of titanium depend on its surface oxide film. Several mechanical and chemical treatments have been used to modify the surface morphology and properties of titanium dental implants. One possible method of improving dental implant biocompatibility is to increase surface roughness and decrease the contact angle. In the present work, the biological properties of dental implants were investigated through in vivo and in vitro tests. The effects of surface roughness, contact angle and surface morphology on titanium dental implant removal torque were investigated. Machined dental implants and discs made with commercially pure titanium ASTM grade 4 were submitted to sandblasting treatments, acid etching and anodizing. The sample surface morphologies were characterized by SEM, the surface roughness parameters were quantified using a laser non-contact profilometer, and a contact angle measurement was taken. Dental implants were placed in the tibia of rabbits and removed 12 weeks after the surgery. It was found that: (i) acid etching homogenized the surface roughness parameters; (ii) the anodized surface presented the smallest contact angle; (iii) the in vivo test suggested that, in similar conditions, the surface treatment had a beneficial effect on the implant biocompatibility measured through removal torque; and (iv) the anodized dental implant presented the highest removal torque.

Although it is well accepted that implant success is dependent on various surface properties, little is known about the effect of surface roughness on cell metabolism or differentiation, or whether the effects vary with the maturational state of the cells interacting with the implant. In the current study, we examined the effect of titanium (Ti) surface roughness on chondrocyte proliferation, differentiation, and matrix synthesis using cells derived from known stages of endochondral development. Chondrocytes derived from the resting zone (RCs) and growth zone (GCs) of rat costochondral cartilage were cultured on Ti disks that were prepared as follows: HF-HNO3-treated and washed (PT); PT-treated and electropolished (EP); fine sand-blasted, HCl-H2SO4-etched, and washed (FA); coarse sand-blasted, HCl-H2SO4-etched, and washed (CA); or Ti plasma-sprayed (TPS). Based on surface analysis, the Ti surfaces were ranked from smoothest to roughest: EP, PT, FA, CA, and TPS. Cell proliferation was assessed by cell number and [3H]-thymidine incorporation, and RNA synthesis was assessed by [3H]-uridine incorporation. Differentiation was determined by alkaline phosphatase specific activity (AL-Pase). Matrix production was measured by [3H]-proline incorporation into collagenase-digestible (CDP) and noncollagenase-digestible (NCP) protein and by [35S]-sulfate incorporation into proteoglycan. GCs required two trypsinizations for complete removal from the culture disks; the number of cells released by the first trypsinization was generally decreased with increasing surface roughness while that released by the second trypsinization was increased. In RC cultures, cell number was similarly decreased on the rougher surfaces; only minimal numbers of RCs were released by a second trypsinization. [3H]-thymidine incorporation by RCs decreased with increasing surface roughness while that by GCs was increased. [3H]-Uridine incorporation by both GCs and RCs was greater on rough surfaces. Conversely, ALPase in the cell layer and isolated cells of both cell types was significantly decreased. GC CDP and NCP production was significantly decreased on rough surfaces while CDP production by RC cells was significantly decreased on smooth surfaces. [35S]-sulfate incorporation by RCs and GCs was decreased on all surfaces compared to tissue culture plastic. The results of this study indicate that surface roughness affects chondrocyte proliferation, differentiation, and matrix synthesis, and that this regulation is cell maturation dependent. © 1996 John Wiley & Sons, Inc.

The European Union (EU) implemented the waste electrical and electronic equipment (WEEE) and restriction of hazardous substances (RoHS) directives in July 2006. To fulfil the environmental ethos of these EU directives, a printed circuit board (PCB) was developed based on a currently mass-manufactured board, but using a substrate of paper card, with interconnecting tracks added using conductive ink via a printing process. Components were bonded to the tracks using electrically conductive adhesives via an industry-based manufacturing line. During this investigation, paper card substrates of varying surface roughness were examined to establish the effect of substrate surface roughness for printing an interconnecting pattern for single-sided boards. Four degradable card substrate types with surface roughness values varying from 0.25 to 2.66 μm were trialled. The impact of substrate surface roughness on track resistance was investigated and a correlation between increased substrate roughness and a reduction in track resistance was established, a reduction in track resistance of up to 56% was observed. Flammability analysis of the substrates was performed in accordance with BS61189-2, while mechanical, electrical, and functional tests were undertaken inline with international standards. The developed PCBs were deemed to have met this established criteria, thus opening the possibility of producing a WEEE/RoHS-compliant environment-friendly PCB.

Satellite Test of the Equivalence Principle (STEP) proposes to use niobium thin film strip-line circuits on precision quartz assemblies to achieve on-orbit differential acceleration sensitivities of 10-18 g. The acceleration is determined from a displacement measurement under known spring stiffness. Currents trapped in niobium circuits (400 nm thick, 100 mum wide) provide magnetic spring forces, and in conjunction with a SQUID magnetometer, the displacement measurement. We have studied the effect of substrate surface roughness on the critical current and temperature of niobium thin film strip-line circuits. We have observed a critical current that decreases with increasing surface roughness, with no change in critical temperature. We attribute the decrease in critical current to a flux penetration barrier at the strip-line edge that decreases with increasing surface roughness. This is a significant finding for the development of the STEP instrument, since anomalous flux penetration at the edge of circuits can degrade performance, add SQUID sensor noise, and lead to trapped flux instabilities.

Wetting of soy protein adhesives modified by urea on wood surfaces was investigated with sessile liquid droplet method. Dynamic contact angles were used to illustrate the wetting process. The effects of wood surface roughness and urea concentration on contact angles were investigated. Moreover, two wetting models were used to describe the dynamic contact angle process, in which the contact angle change rate constant (K) can be used to quantify the adhesive spreading and penetration during the wetting process. The results showed that the wetting models could accurately describe the dynamic wetting process of soy protein adhesives on wood surfaces.

The Effect of Drop (Bubble) Size on Advancing and Receding Contact Angles for Heterogeneous and Rough Solid Surfaces as Observed with Sessile-Drop and Captive-Bubble Techniques

Different types of land cover are associated with different surface roughness, which produce variations in the frictional force on the wind. Therefore, mean wind profiles at low levels often differ markedly over short distances where there is a gradient in surface roughness. Horizontal gradients in surface roughness may produce vertical vorticity, circulation, and horizontal divergence. The effect of roughness on vertical wind shear and storm-relative helicity is also qualitatively important and may lead to large gradients in helicity over short distances. Recent studies also suggest an important role of friction in tornadogenesis.&#x0D; We show conceptually and theoretically how gradients in surface roughness produce quasi-ambient convergence and vertical vorticity, and gradients in vertical shear and storm-relative helicity. We then present observational data and numerical simulations that demonstrate the effects of surface roughness on the kinematics and shear of boundary-layer flow, for future work examining the importance of these processes for tornadogenesis.

The effects of surface roughness on fully developed laminar and transitional flow friction factors and heat transfer coefficients in horizontal circular tubes