The mF mode of authenticated encryption with associated data

The Clean Air Mercury Rule (CAMR) which was published in the Federal Register on May 18, 2005, requires that calibration of mercury continuous emissions monitors (CEMs) be performed with NIST-traceable standards. Western Research Institute (WRI) is working closely with the Electric Power Research Institute (EPRI), the National Institute of Standards and Technology (NIST), and the Environmental Protection Agency (EPA) to facilitate the development of the experimental criteria for a NIST traceability protocol for dynamic elemental mercury vapor generators. The traceability protocol will be written by EPA. Traceability will be based on the actual analysis of the output of each calibration unit at several concentration levels ranging from about 2-40 ug/m{sup 3}, and this analysis will be directly traceable to analyses by NIST using isotope dilution inductively coupled plasma/mass spectrometry (ID ICP/MS) through a chain of analyses linking the calibration unit in the power plant to the NIST ID ICP/MS. Prior to this project, NIST did not provide a recommended mercury vapor pressure equation or list mercury vapor pressure in its vapor pressure database. The NIST Physical and Chemical Properties Division in Boulder, Colorado was subcontracted under this project to study the issue in detail and to recommend a mercury vapormore » pressure equation that the vendors of mercury vapor pressure calibration units can use to calculate the elemental mercury vapor concentration in an equilibrium chamber at a particular temperature. As part of this study, a preliminary evaluation of calibration units from five vendors was made. The work was performed by NIST in Gaithersburg, MD and Joe Rovani from WRI who traveled to NIST as a Visiting Scientist.« less

This paper presents the employment of a DPA attack on the NIST (National Institute of Standards and Technology) standardized AES (advance encryption standard) protocol for key retrieval and prevention. Towards key retrieval, we applied the DPA attack on AES to obtain a 128-bit secret key by measuring the power traces of the computations involved in the algorithm. In resistance to the DPA attack, we proposed a countermeasure, or a new modified masking scheme, comprising (i) Boolean and (ii) multiplicative masking, for linear and non-linear operations of AES, respectively. Furthermore, we improved the complexity involved in Boolean masking by introducing Rebecca’s approximation. Moreover, we provide a novel solution to tackle the zero mask problem in multiplicative masking. To evaluate the power traces, we propose our custom correlation technique, which results in a decrease in the calculation time. The synthesis results for original implementation (without countermeasure) and inclusion of countermeasure are given on a Zynq 7020 FPGA (Artix-7 device). It takes 424 FPGA slices when implemented without considering the countermeasure, whereas 714 slices are required to implement AES with the inclusion of the proposed countermeasure. Consequently, the implementation results provide the acceptability of this work for area-constrained applications that require prevention against DPA attacks.

A Look at its Past Decade and a Gaze towards its Future. As the National Metrology Institute (NMI) for the United States, the National Institute of Standards and Technology (NIST), formerly the National Bureau of Standards, has provided measurement services, both calibrations and reference materials, for more than 100 years. Through these services, our customers have benefitted from our measurement capabilities and expertise in many areas, including amount of substance; dimensional metrology; electricity and magnetism; ionizing radiation; mass and related quantities; photometry and radiometry; thermodynamics; and time and frequency. NIST’s customers have also had access to some of the lowest measurement uncertainties available and a dependable way to establish traceability to the International System of Units (SI) [http://www.nist.gov/pml/wmd/metric/si-units.cfm].In response to the signing of the International Committee for Weights and Measures (CIPM) Mutual Recognition Arrangement (MRA), NIST first established an institution-wide quality system for the measurement services 10 years ago [http://www.bipm.org/en/cipm-mra/objectives.html]. NIST’s Quality System for Measurement Services has advanced the quality of service and measurements we provide our customers by fostering an environment in which NIST management and staff work towards continual improvement in the development and delivery of NIST measurement services. This paper describes NIST’s Quality System for the Measurement Services and its relevance to international standards of quality, such as the International Organization for Standardization and the International Electrotechnical Commission (ISO/IEC) 17025 standard and ISO Guide 34 [http://www.nist.gov/nistqs/]. It also provides a history of this quality system and a glimpse of future goals for improving its implementation.

Standards provide critical benefits across a wide variety of contexts, including safety and health, environmental protection, and quality of products and services. However, while these benefits are generally acknowledged, estimating the social and economic value of standards and determining how specific entities and activities influence their development require careful analysis. In October of 2018, the National Institute of Standards and Technology (NIST) asked the RAND Corporation to estimate the benefit of NIST’s research contributing to particular fire safety standards. The original objectives of the project were to (1) document the role of the NIST in the standards development process, (2) estimate the value these standards provide to society, and (3) thereby inform the economic value of NIST’s contribution to these standards. This report presents results for the first two objectives. Given that NIST’s contribution is one of several inputs combining to create these standards, NIST’s share of the credit for their value could not be quantified. Our analysis focused on case studies in standards for home smoke alarms and for protecting structures at the wildland-urban interface (WUI). Our analysis draws on a wide variety of qualitative and quantitative methods to holistically describe the impacts of these standards and NIST’s role in their development. The intended audience of this report includes those who work on fire safety research, fire safety standards, building codes, and technology transfer. The conclusions presented here may also be of interest for broader resource allocation and federal budget justification purposes. Finally, this report was written to be accessible to any interested members of the general public.

In the fall of 2019, the National Institute of Standards and Technology (NIST) funded threes studies to better understand equity and inclusivity. This report documents phase two of a three phased sequential, exploratory mixed methods study designed to provide an in-depth look at the population of NIST federal employees to identify factors, attitudes, and processes that might result in gender- specific barriers at NIST. Phase 1 analyzed human resources demographic data, compensation data, and performance data of NIST federal employees from 2011 to 2019 to determine any relevant trends. Phase 1 informed the development of an in-depth interview protocol designed to identify the differences, if any, in the ways in which men and women experience work at NIST. A total of 40 (36 female and 4 male) participants were interviewed. Three interconnected themes emerged in the data: 1) a culture at NIST that creates a Chilly Climate for women; 2) gendered experiences that contribute to and are outcomes of that chilly climate; and 3) gendered outcomes that influence women s experiences in the organization. The culture has evolved from NIST s scientific roots, scientific excellence, a strong belief in meritocracy, and as a Federal agency. Each of these characteristics contribute to a gendered social structure and the perception that change is not needed. This backdrop sets the stage for the characterizations of NIST from the interviews as a Boys Club and an Elitist environment. The radically different perspectives of men and women based in the culture result in experiences and outcomes that provide advantages and opportunities for men while erecting barriers to survival for women, including isolation and possibly exclusion. These barriers result in consequences of discrimination as well as lack of trust and resignation. Participant quotes are used as exemplars to provide details related to each of these themes. Overall, the interviews demonstrate that women and men experience a very different NIST.

The National Institute of Standards and Technology (NIST), formerly the National Bureau of Standards, was established by the U.S. Congress in 1901 and charged with establishing a measurement foundation to facilitate U.S. and international commerce. NIST provides reference materials and reference instruments that are used to ensure the accuracy, metrological traceability, and comparability of measurement results in many diverse fields of science, industry, and technology. This document provides and explains the vocabulary used at NIST to describe the reference materials and reference instruments available to NIST s customers. This document also describes the methods used in developing NIST reference materials. The definitions and descriptions provided supersede those used in the original versions of this publication, NIST SP260-136 and SP260-136-2020.

This paper presents a summary of the strategies and activities underway at the National Institute of Standards and Technology (NIST) in electronics packaging, interconnection and assembly (P/I/A). In addition, a sampling of collaborations involving these works is included. The overall NIST effort in P/I/A is composed of targeted programs conducted by the NIST laboratories and by the NIST Advanced Technology Program (ATP). A dominant aspect of the laboratory-based P/I/A program focuses on the metrology and data needed to support the product technologies envisioned within industry roadmaps. A significant aspect of the work includes efforts in metrology, materials, complex material assemblies, and microelectronic components and circuits. In parallel, the NIST ATP is supporting on a cost-share basis a variety of industry-based development projects of high-risk enabling technologies for new or improved products, manufacturing, and processes in P/I/A.

The National Institute of Standards and Technology (NIST) timescale produces a real-time realization of UTC(NIST) in the form of a pulse-per-second (PPS) time signal and a 5 MHz frequency reference. UTC(NIST) contributes to UTC (Coordinate Universal Time) using TWSTFT (Two-Way Satellite Time and Frequency Transfer) and common-view GPS (Global Positioning System) techniques. The NIST timing signal is also disseminated to the international and domestic communities using various other techniques: NIST Automated Computer Time Service (ACTS), Internet Time Service (ITS) and NIST Time Measurement and Analysis Service (TMAS). The accuracy of NIST contribution to UTC and of the dissemination of the NIST PPS time signal depends upon the quality of the calibration of the time delay between each user and the UTC(NIST) reference point. Hardware constraints, spatial constraints, and in some cases simple convenience, require that the physical input to the transfer and dissemination equipment be distributed throughout the NIST campus. A robust on-campus timing distribution and calibration system is required to ensure the accuracy and stability of these signals: for example, the current error budget for a typical time transfer calibration requires local delays to be known to an uncertainty of less than 200 ps. We utilize a clock trip calibration protocol to measure the delays introduced by the local time distribution system at NIST: a clock trip involves measuring the time difference between the UTC(NIST) reference point and a travelling clock, then transporting the travelling clock to a secondary reference point where another measurement of the time difference is performed. Clock trips are advantageous as they are a nonintrusive measurement of the full system delay. To achieve calibrations with an accuracy on the order 100 ps, we have developed a means to transport a cesium clock between remote locations on site with minimal vibration and an analysis protocol to maximize the information acquired by each clock trip. We will introduce the system used to distribute time signals at NIST, the hardware and protocol we have developed to calibrate secondary timing reference points, and data we have collected based on their implementation.

With today's development and expansion of networks and internet-connected devices, information security is an issue of increasing concern. Confidentiality is one of the focuses in network security for digital communication systems, where large data blocks go through a cryptographic algorithm with a cipher key that increases the security and complexity of the output ciphertext. For the past several years, multiple security algorithms have been developed and utilized in the data encryption process, such as the Data Encryption Standard (DES), Triple Data Encryption Standard (3DES), and the current one, designated by the U.S. National Institute of Standards and Technology (NIST), the Advanced Encryption Standard (AES). AES is a symmetric encryption algorithm that has a minimum input data block size of 128-bits which undergo a series of permutations, substitutions, and digital logic operations over several rounds. Encryption algorithms are always improving on ciphertext complexity, required hardware storage allocation, and execution time. Field Programmable Gate Arrays (FPGA's) are a hardware alternative for encryption algorithm implementation because, although the logic units in it are fixed, the functions and interconnections between them are based on the user's design which allow for improvement. The research presented focuses on the development and analysis of an efficient AES-128 Mix Columns algorithm implementation, utilized in the data block encryption rounds, on an Altera Cyclone IV FPGA using the Intel Quartus II software and Verilog Hardware Description Language.

November 2001, the National Institute of Standards and Technology (NIST) Rijndael algorithm to determine the new Data Encryption Standard - Advanced Encryption Standard (AES). AES cryptanalysis is one of the most high-profile issue. This review introduces the AES Some New Advances in cryptanalysis: cryptanalysis, including algebra, analysis of energy consumption, related key attacks and attacks based on key arrangement. These sum up, I hope the actual engineering applications to overcome these problems, in order to achieve safe use.

As cybersecurity issues surge, it highlights the pressing need for increased awareness. In our digitally interconnected world, where information technology underpins the lives of individuals, businesses, and even national security, the threat of cyberattacks looms large. To enhance national cybersecurity preparedness, there is a critical call to action: we must promote public awareness of cybersecurity issues and bolster the ranks of trained cybersecurity professionals. This research introduces a novel cybersecurity awareness model based on the National Institute of Standards and Technology (NIST). Its primary goal is to make NIST accessible to secondary school students pursuing ICT courses and their invaluable resource, the school counselling units. The model aims to instil cybersecurity awareness in secondary school students and guide them in choosing the most suitable higher education paths, particularly in the ICT and cybersecurity fields. The study comprises three phases. In the first phase, a systematic literature review (SLR) examines globally applicable cybersecurity education models. The second phase investigates the implementation of cybersecurity education for secondary school students in Malaysia. This includes interviews with school counselling units responsible for guiding students toward higher education and surveys of students in grades four and five enrolled in ICT courses. The third and pivotal phase focuses on developing the proposed model. It involves analysing and implementing the results of the SLR, mapping them to the NIST framework, and incorporating themes from interviews and surveys. As a tangible representation of the model, a mobile application prototype has been developed. The Cybersecurity Awareness Model empowers school counselling units to seamlessly integrate career exploration with career decision-making for secondary students at any stage of their development. Moreover, it offers a means to create strategies for after-school programs, particularly in the dynamic field of cybersecurity. This model is expected to guide students in exploring academic majors and careers, preparing for higher education post-high school, initiating internships or job searches, and adapting to a world in constant flux. In doing so, it not only empowers individuals but also strengthens the nation's resilience in the face of cybersecurity challenges.

On September 5–8, 2023, the National Institute of Standards and Technology (NIST) held the second Standards and Performance Metrics for On‐Road Automated Vehicles Workshop. This four‐day virtual event provided updates on NIST’s recent work in automated vehicles (AVs) and gave stakeholders an opportunity to provide feedback and input on current and future NIST research. The workshop included high‐level keynote presentations, a series of industry keynote presentations, and NIST presentations on its current AV activities. The industry keynotes and NIST presentations were paired with breakout sessions that discussed NIST’s progress, community challenges, and stakeholder research needs in six key areas: systems interaction, perception, cybersecurity, communications, artificial intelligence, and digital infrastructure. There was general agreement that developing standards allows for better comparisons and evaluations of emerging technologies. Other key themes included: 1) Digital technologies for automation and related security/privacy concerns, including artificial intelligence, machine learning, and smart communication technologies (i.e., vehicle‐to‐vehicle (V2V), vehicle‐to‐infrastructure (V2I), and vehicle‐to‐everything (V2X)), 2) Need for standardized or common language to improve information sharing, 3) Open data sets to support and validate technical advances and standardization across system components and areas (i.e., standards evolving in parallel with technology), and 4) Pivotal role for NIST as a convener to bring diverse stakeholders together for knowledge exchange and cross‐industry dialogue.

In consultation with ASTM and other stakeholders in Tissue-Engineered Medical Products (TEMPs) industry, the National Institute of Standards and Technology (NIST) initiated a project designed to produce Reference Material scaffolds for tissue engineering. The rationale for Reference Material scaffolds was developed through several NIST/Industry workshops. In brief, Reference Material scaffolds have multiple uses: facilitating the development and the validation of new test methods that measure interactions among various components of a TEMP; comparison with other scaffolds and scaffold materials in terms of cellular responses, biodegradation, and releases of growth factors; and comparisons of responses among various cell lines. The primary customers for Reference Material scaffolds are expected to be the TEMPs industry, academic researchers, regulators, and standards developing organizations. There are many properties of a TEMP that warrant development of multiple Reference Material scaffolds. Currently, NIST is defining a set of Reference Material scaffolds based on geometric descriptors such as permeability, pore volume, pore size distribution, interconnectivity, and tortuosity. In consultation with ASTM, NIST is testing three candidate scaffolds produced by: three dimensional (3-D) printing, stereolithography, and fused deposition modeling (FDM). Scaffolds made by these methods have been obtained from Mayo Clinic (Rochester, MN), Case Western Reserve University (CWRU) (Cleveland, OH), and Osteopore International (Singapore), respectively, for structural characterization. These prototype scaffolds, with well-defined architectures, have been selected to address the following items of interest: 1) establishment of useful functional definitions of porosity content, interconnectivity, and pores; 2) evaluation of testing methods listed in the Standard Guide for the Porosity of Polymeric Scaffolds for Use in Tissue-Engineered Medical Products, which is being drafted by ASTM. Currently, NIST and the Center for Devices and Radiological Health of the Food and Drug Administration, as well as other groups from US and foreign laboratories, are actively carrying out cross-validation test of these prototype scaffolds.

Efficiency is essential in lightweight cryptography to ensure robust protection within constrained environments. This paper introduces a lightweight block cipher built on a Non-Linear Feedback Shift Register (NFSR), referred to as the NFSR-Based Block Cipher (NFBC). The cipher is designed for constrained environments where both efficiency and strong security are critical. NFBC operates as a Nonce-based Authenticated Encryption with Associated Data (NAEAD) scheme, providing confidentiality and authenticity within a single framework. The design achieves robust protection while maintaining minimal hardware overhead. NFBC operates on 128-bit data, key, and nonce sizes, fully aligning with National Institute of Standards and Technology (NIST) lightweight cryptography requirements. The design integrates a Non-Linear Feedback Shift Register (NFSR) for generating high-entropy round subkeys, dynamic chaotic substitution box (S-boxes) for strong confusion, and a Group Permutation (GRP) mechanism that ensures rapid diffusion with hardware-friendly efficiency. Security is rigorously evaluated across multiple dimensions. NFBC passes all 15 NIST Statistical Test Suite (STS) tests, achieves near-ideal avalanche and Bit Independence Criterion (BIC), and demonstrates consistently high nonlinearity across 200 independent chaotic S-box instances. The S-box achieves a maximum differential probability of 10/256 and maximum linear probability of (72/256)^{2}, confirming strong resistance to classical attacks. To strengthen theoretical guarantees, a provable branch-number analysis is introduced, establishing conservative lower bounds on active S-boxes (ge 45 across 20 rounds), with corresponding differential and linear probabilities that are vanishingly small. Formal AEAD security is ensured through an Encrypt-then-MAC (EtM) construction. Implementation on a Xilinx Artix-7 FPGA confirms practicality: NFBC achieves superior throughput-per-area compared to several NIST Round-2 lightweight candidates (SPOC, SPOOK, GIFT-COFB, ESTATE, SAEAES, Oribatida) and CAESAR finalists (Ascon-128, Ascon-small, CLOC-AES, SILC-AES). Estimated countermeasure overheads for masking and fault detection demonstrate feasibility against side-channel and fault attacks. These results confirm NFBC as a secure, efficient, and practically deployable lightweight cryptographic solution.

An image encryption scheme based on elliptic curve pseudo random and Advanced Encryption System