The PPP Precision Analysis Based on BDS Regional Navigation System

The BeiDou Navigation Satellite System (BDS) offers orbit and clock corrections through the B2b signal, enabling Precise Point Positioning (PPP) without relying on ground communication networks. This capability supports applications such as aerial and maritime mapping. However, achieving high precision during the convergence period remains challenging, particularly for missions with short observation durations. To address this, we analyze the performance of PPP over short periods using PPP-B2b products and propose using the backward smoothing method to enhance the accuracy during the convergence period. Evaluation of the accuracy of PPP-B2b products shows that the orbit and clock accuracy of the BDS surpass those of GPS. Specifically, the BDS achieves orbit accuracies of 0.059 m, 0.178 m, and 0.186 m in the radial, along-track, and cross-track components, respectively, with a clock accuracy within 0.13 ns. The hourly static PPP achieves 0.5 m and 0.1 m accuracies with convergence times of 4.5 and 25 min at a 50% proportion, respectively. Nonetheless, 7.07% to 23.79% of sessions fail to converge to 0.1 m due to the limited availability of GPS and BDS corrections at certain stations. Simulated kinematic PPP requires an additional 1–4 min to reach the same accuracy as the static PPP. Using the backward smoothing method significantly enhances accuracy, achieving 0.024 m, 0.046 m, and 0.053 m in the north, east, and up directions, respectively. For vehicle-based positioning, forward PPP can achieve a horizontal accuracy better than 0.5 m within 4 min; however, during the convergence period, positioning errors may exceed 1.5 m and 3.0 m in the east and up direction. By applying the smoothing method, horizontal accuracy can reach better than 0.2 m, while the vertical accuracy can improve to better than 0.3 m.

The currently available triple-frequency signals give rise to new prospects for precise point positioning (PPP). However, they also bring new bias, such as time-varying parts of the phase bias in the hardware of receivers and satellites due to the fact that dual-frequency precise clock products cannot be directly applied to triple-frequency observation. These parameters generate phase-based inter-frequency clock bias (PIFCB), which impacts the PPP. However, the PIFCBs of satellites are not present in all GNSSs. In this paper, various IF1213 PPP models are constructed for these parts, namely, the triple-frequency PIFCB (TF-C) model with PIFCB estimation, the TF inter-frequency bias (IFB) (TF-F) model ignoring the PIFCB, and the TF-PIFCB-IFB (TF-CF) model with one system PIFCB estimation. Additionally, this study compares these IF1213 PPP models with the dual-frequency ionosphere-free (DF) model. We conducted single system static PPP, dual-system static and kinematic PPP experiments based on BDS/GPS observation data. The GPS static PPP experiment demonstrates the reliability of the TF-C model, as well as the non-negligibility of the GPS PIFCB. The BDS static PPP experiment demonstrates the reliability of the TF-F and TF-CF models, and that the influence of the BDS-2 PIFCB can be neglected in BDS. The BDS/GPS PPP experimental results show that the third frequency does not significantly improve the positioning accuracy but shortens the convergence time. The positioning accuracy of TF-C and TF-CF for static PPP is better than 1.0 cm, while that for kinematic PPP is better than 2.0 cm and 4.0 cm in the horizontal and vertical components, respectively. Compared with the DF model, the convergence time of the TF-C and TF-CF models for static PPP is improved by approximately 23.5%/18.1%, 13.6%/9.7%, and 19.8%/12.1%, while that for kinematic PPP is improved by approximately 46.2%/49.6%, 33.5%/32.4%, and 35.1%/36.1% in the E, N and U directions, respectively. For dual-system PPP based on BDS/GPS observations, the TF-C model is recommended.

Although there are already several real-time precise positioning service providers, unfortunately, not all users can use the correction information due to either cost of the service and limitation of their equipment or out of the service coverage. An alternative way is to enhance the accuracy of the predicted satellite clocks for precise real-time positioning. Based on the study of existing prediction models, an improved model combing the spectrum analysis (SA) and the generalized regression neural network (GRNN) model is proposed especially for BeiDou satellite navigation system (BDS)-2 satellites. The periodic terms and GRNN-related parameters including length and interval of sample data, as well as a smooth factor, are optimized satellite by satellite to consider satellite-specific characteristics for all the fourteen BDS-2 satellites. The improved model is validated by comparing the predicted clocks of existing models and the improved model with precisely estimated ones. The bias of the predicted clock is within ±0.5 ns over three hours and better than that of the other models and can be used for several real-time precise applications. The clock prediction is further evaluated by applying clock corrections to precise point positioning (PPP) in both static and kinematic mode for eight IGS (International GNSS Service) MGEX (Multi-GNSS Experiment) stations in the Asia-Pacific region. In the static PPP, the improved model is validated to be effective, and position accuracies of some IGS MGEX stations achieve more than 30.0% improvements on average for each component, which enables us to obtain sub-decimeter positioning. In the kinematic PPP, the improved model performs much better than the others in terms of both the convergence time and the position accuracy. The convergence time can be shortened from 1–2 h to 0.5–1 h, while the position accuracy is enhanced by 15.4%, 21.6% and 19.3% on average in east, north and up component, respectively.

Real-time capability , positioning accuracy and convergence time ar e the keys to the performance of Precise Point Positioning (PPP). In recent years, the development of IGS Real-Time Services (RTS) has improved the performance of real-time PPP to a large extent. Meanwhile, the PPP ambiguity resolution technique, which significantly improves the positioning accuracy and convergence time, has become mature gradually. If the advantages of both techniques can be combined to realize real-time PPP with ambiguity resolution, the application of PPP would be greatly expanded. In this paper, a real-time satellite-satellite single-difference fractional cycle bias (FCB) estimation method based on RTS products is proposed. To meet the demand of real-time PPP, narrow-lane FCBs are forecasted by short-term linear extrapolation. Taking accuracy levels and data amount into consideration, the forecasting interval for real-time wide-lane and narrow-lane FCBs are determined. Finally, the performance of real-time PPP with ambiguity resolution using real-time FCBs is evaluated in both static and kinematic modes. The results show that wide-lane FCBs to be forecasted daily and narrow-lane FCBs to be forecasted every 5 min can satisfy the need of real-time PPP with ambiguity resolution. In static mode, the average time to first fix (TTFF) is 15.97 min, and the average precision of the north, east and up components for hourly solution are 1.51, 1.64 and 2.18 cm respectively. As for kinematic mode, an average TTFF of 24.36 min is needed, and the 3D position error in fixed solution is decreased by 42.59% compared with float solution.

Because of the special design of BeiDou navigation satellite system (BDS) constellation, the effects of ionospheric scintillation on operational BDS generally are more serious than on the global positioning system (GPS). As BDS is currently providing global services, it is increasingly important to seek strategies to mitigate the scintillation effects on BDS navigation and positioning services. In this study, an improved cycle-slip threshold model is proposed to decrease the high false-alarm rate of cycle-slips under scintillation conditions, thus avoiding the frequent unnecessary ambiguity resets in BDS precise point positioning (PPP) solution. We use one-year (from 23 March 2015 to 23 March 2016) BDS dataset from Hong Kong Sha Tin (HKST) station (22.4°N, 114.2°E; geomagnetic latitude: 15.4°N) to model the cycle-slip threshold and try to make it suitable for three types of BDS satellites and multiple scintillation levels. The availability of our mitigation strategy is validated by using three months (from 1 September 2015 to 30 November 2015) BDS dataset collected at 10 global navigation satellite system (GNSS) stations in Hong Kong. Positioning results demonstrate that our mitigated BDS PPP can prevent the sudden fluctuations of positioning errors induced by the ionospheric scintillation. Statistical results of BDS PPP experiments show that the mitigated solution can maintain an accuracy of about 0.08 m and 0.10 m in the horizontal and vertical components, respectively. Compared with standard BDS PPP, the accuracy of mitigated PPP can be improved by approximately 24.1%, 38.2%, and 47.9% in the east, north, and up directions, respectively. Our study demonstrates that considering different scintillation levels to establish appropriate cycle-slip threshold model in PPP processing can efficiently mitigate the ionospheric scintillation effects on BDS PPP.

The BeiDou navigation satellite system (BDS) currently has 41 satellites in orbits and will reach its full constellation following the launch of the last BDS satellite in June 2020 to provide navigation, positioning, and timing (PNT) services for global users. In this contribution, we investigate the characteristics of inter-system bias (ISB) between BDS-2 and BDS-3 and verify whether an additional ISB parameter should be introduced for the BDS-2 and BDS-3 precise point positioning (PPP). The results reveal that because of different clock references applied for BDS-2 and BDS-3 in the International GNSS Service (IGS) precise satellites clock products and the inconsistent code hardware delays of BDS-2 and BDS-3 for some receiver types, an ISB parameter needs to be introduced for BDS-2 and BDS-3 PPP. Further, the results show that the ISB can be regarded as a constant within a day, the value of which is closely related to the receiver type. The ISB values of the stations with the same receiver type are similar to each other, but a great difference may be presented for different receiver types, up to several meters. In addition, the impact of ISB on PPP has also been studied, which demonstrates that the performance of kinematic PPP could be improved when ISB is introduced.

For time-critical precise applications, one popular technology is the real-time precise point positioning (PPP). In recent years, there has been a rapid development in the BeiDou Navigation Satellite System (BDS), and the constellation of global BDS (BDS-3) has been fully deployed. In addition to the regional BDS (BDS-2) constellation, the real-time stream CLK93 has started to support the BDS-3 constellation, indicating that the real-time PPP processing involving BDS-3 observations is feasible. In this study, the global positioning performance of real-time PPP with BDS-3/BDS-2 observations is initially evaluated using the datasets from 147 stations. In the east, north and upward directions, positioning accuracy of 1.8, 1.2 and 2.5 cm in the static mode, and of 6.7, 5.1 and 10.4 cm in the kinematic mode can be achieved for the BDS-3/BDS-2 real-time PPP, respectively, while the corresponding convergence time with a threshold of 10 cm is 32.9, 23.7 and 32.8 min, and 66.9, 42.9 and 69.1 min in the two modes in the three directions, respectively. To complete this, the availability of BDS-3/BDS-2 constellations, the quality of BDS-3/BDS-2 real-time precise satellite products, and the BDS-3/BDS-2 post-processed PPP solutions are also analyzed. For comparison, the results for the GPS are also presented.

With the development of precise point positioning (PPP), the School of Geodesy and Geomatics (SGG) at Wuhan University is now routinely producing GPS satellite fractional cycle bias (FCB) products with open access for worldwide PPP users to conduct ambiguity-fixed PPP solution. We provide a brief theoretical background of PPP and present the strategies and models to compute the FCB products. The practical realization of the two-step (wide-lane and narrow-lane) FCB estimation scheme is described in detail. With GPS measurements taken in various situations, i.e., static, dynamic, and on low earth orbit (LEO) satellites, the quality of FCB estimation and the effectiveness of PPP ambiguity resolution (AR) are evaluated. The comparison with CNES FCBs indicated that our FCBs had a good consistency with the CNES ones. For wide-lane FCB, almost all the differences of the two products were within ±0.05 cycles. For narrow-lane FCB, 87.8 % of the differences were located between ±0.05 cycles, and 97.4 % of them were located between ±0.075 cycles. The experimental results showed that, compared with conventional ambiguity-float PPP, the averaged position RMS of static PPP can be improved from (3.6, 1.4, 3.6) to (2.0, 1.0, 2.7) centimeters for ambiguity-fixed PPP. The average accuracy improvement in the east, north, and up components reached 44.4, 28.6, and 25.0 %, respectively. A kinematic, ambiguity-fixed PPP test with observation of 80 min achieved a position accuracy of better than 5 cm at the one-sigma level in all three coordinate components. Compared with the results of ambiguity-float, kinematic PPP, the positioning biases of ambiguity-fixed PPP were improved by about 78.2, 20.8, and 65.1 % in east, north, and up. The RMS of LEO PPP test was improved by about 23.0, 37.0, and 43.0 % for GRACE-A and GRACE-B in radial, tangential, and normal directions when AR was applied to the same data set. These results demonstrated that the SGG FCB products can be produced with high quality for users anywhere around the world to carry out ambiguity-fixed PPP solutions.

High-rate multi-constellation global navigation satellite system (GNSS) precise point positioning (PPP) has been recognized as an efficient and reliable technique for large earthquake monitoring. However, the displacements derived from PPP are often overwhelmed by the centimeter-level noise, therefore they are usually unable to detect slight deformations which could provide new findings for geophysics. In this paper, Global Positioning System (GPS), GLObalnaya NAvigatsionnaya Sputnikovaya Sistema (GLONASS), and BeiDou navigation satellite system (BDS) data collected during the 2017 Mw 6.5 Jiuzhaigou earthquake were used to further exploit the capability of BDS-only and multi-GNSS PPP in deformation monitoring by applying sidereal filtering (SF) in the observation domain. The equation that unifies the residuals for the uncombined and undifferenced (UCUD) PPP solution on different frequencies was derived, which could greatly reduce the complexity of data processing. An unanticipated long-term periodic error term of up to ± 3 cm was found in the phase residuals associated with BDS satellites in geostationary Earth orbit (GEO), which is not due to multipath originated from the ground but is in fact satellite dependent. The period of this error is mainly longer than 2000 s and cannot be alleviated by using multi-GNSS. Compared with solutions without sidereal filtering, the application of the SF approach dramatically improves the positioning precision with respect to the weekly averaged positioning solution, by 75.2%, 42.8%, and 56.7% to 2.00, 2.23, and 5.58 cm in the case of BDS-only PPP in the east, north, and up components, respectively, and 71.2%, 27.7%, and 37.9% to 1.25, 0.81, and 3.79 cm in the case of GPS/GLONASS/BDS combined PPP, respectively. The GPS/GLONASS/BDS combined solutions augmented by the SF successfully suppress the GNSS noise, which contributes to the detection of the true seismic signal and is beneficial to the pre- and post-seismic signal analysis.

During high-level solar activity time, frequent ionospheric irregularities lead to large total electron content (TEC) gradient. precise point positioning (PPP) performance can be significantly degraded under the unfavorable ionosphere conditions. We analyze the causes and effects of the ionosphere potential impacts on uncombined PPP (UPPP) performance in terms of the ionospheric stochastic model, blunders, and frequent cycle slips. Results show that a large enough stochastic variance is beneficial for better positioning solutions; blunders detection could improve the accuracy; a proper threshold to detect cycle slips could improve the accuracy significantly. Taking these effects into consideration, we can achieve a centimeter accuracy at each direction under the disturbed ionosphere conditions.

Precise point positioning (PPP) technology is one of the core technologies in the field of GNSS high-precision positioning. It is used widely because it can realize centimeter-level positioning in outdoor environments by using only a single receiver. However, its convergence is time-consuming, particularly in urban areas where satellite occlusion is more severe. A combined BeiDou Navigation Satellite System (BDS) and fifth generation mobile communication technology (5G) PPP observation model is proposed, in which the two kinds of observations are combined and solved at the original observation level. The impact of different numbers and geometries of 5G base stations on the convergence time of PPP is analyzed from both static and dynamic perspectives. The results confirm that PPP technology combining BDS and 5G can effectively accelerate convergence while improving the accuracy of positioning.

Nowadays, both BDS-3 and Galileo can provide global positioning and navigation services. This contribution carried out a comprehensive analysis and validation of positioning performance in terms of positioning accuracy (RMS) and convergence time, which are derived from BDS-3 and Galileo precise point positioning (PPP) solutions at a global scale. Meanwhile, the comparison with GPS was demonstrated. The performance and geographical distribution of RMS and convergence time for each satellite system were analyzed. GPS outperforms the other two systems on a global scale. Galileo and BDS-3, on the other hand, only perform moderately well in certain latitude zones. The combination of dual systems related to each single system is analyzed. For the dual-system combinations, the combination of systems presents a definite advantage over Galileo and BDS-3, and this advantage is more pronounced for the kinematic PPP. For GPS, the combination with Galileo and BDS-3 has little improvement in positioning performance. For the dual-system combination based on Galileo and BDS-3, the RMS and convergence time can be improved by 50% compared with the single system. The influence of single-system kinematic PPP selection for precise products from different MGEX analysis centers on positioning performance was studied. Among the five precise products, grg products have the best positioning performance for GPS, while cod products have the best positioning performance for Galileo and BDS-3. The difference in RMS and convergence time between 2 cm and 15 min can be caused by different precise product selections.

With the full operation of the global BeiDou navigation satellite system (BDS-3), positioning performance can be further enhanced by BDS-3 combined with the regional BeiDou navigation satellite system (BDS-2). However, due to satellite signals being out of lock and the limited visibility of satellites, the traditional multi-frequency BDS-2/3 precise point positioning (PPP) model is unable to maintain great positioning performance under urban environmental conditions. In this study, a mixed multi-frequency undifferenced and uncombined (UDUC) BDS-2/3 PPP model is presented to improve the positioning performance under urban environmental conditions by making full use of B1I, B1C, B2I, B2a, and B3I signals from all visible BDS satellites. In this model, BDS satellites with single-, dual-, triple- and quad-frequency observations all can participate in PPP. The static and kinematic experiments were carried out using the mixed multi-frequency UDUC BDS-2/3 PPP model to fully assess the positioning performance under urban environmental conditions with comparisons to the multi-frequency model. The static experiments indicated that the mixed multi-frequency UDUC BDS-2/3 PPP could continuously achieve decimeter-level positioning accuracy at a cut-off elevation angle of 40°, but part of the BDS-3 PPP would lose resolution due to limited visible satellites. Furthermore, the initial kinematic vehicle experiment showed that mixed multi-frequency UDUC BDS-2/3 PPP had better satellite geometry and more observation redundancy than the traditional multi-frequency model. Compared with the traditional multi-frequency BDS-2/3 model, the positioning accuracy of the mixed multi-frequency model was improved by 51.6, 35.5, and 39.1%, respectively, in east, north, and up directions. The convergence time was shortened by 40%.

BDS (Beidou Navigation Satellite System) integrates the legacy PNT (Positioning, Navigation, Timing) service and the authorized SBAS (Satellite-Based Augmentation Services) service. To support the requirement of decimeter-level positioning, four types of differential corrections are developed in the BDS SBAS, including the State Space Representation (SSR)-based satellite orbit/clock corrections, the Observation Space Representation (OSR)-based ionospheric grid corrections, and the partition comprehensive corrections. In this study, we summarize the features of these differential corrections, including their definition and usages. The function model of precise point positioning (PPP) for dual- and single-frequency users using the four types of BDS SBAS corrections are proposed. Datasets are collected from 34 stations over one month in 2019, and PPP is performed for all the datasets. Results show that the root mean square (RMS) of the positioning errors for static/kinematic dual-frequency (DF) PPP are of 12 cm/16 cm in horizontal and 18 cm/20 cm in vertical component, while for single-frequency (SF) PPP are of 14 cm/32 cm and 22 cm/40 cm, respectively. With regard to the convergence performance, the horizontal and vertical positioning errors of kinematic DF-PPP can converge to 0.5 m in less than 15 min and 20 min, respectively. As for the kinematic SF-PPP, it could converge to 0.8 m in horizontal and 1.0 m in vertical within 30 min, where the ionosphere-constrained PPP performs better than the UofC PPP approach, owing to the contribution of the ionospheric grid corrections.

Monitoring the response of engineering structures, such as tall buildings, tower and large-scale bridges, under severe loading conditions, such as strong earthquake or wind storm, is an important requirement to verify their design and construction and to evaluate structural condition and reliability. In the last two decades, high-rate real-time or post-processed kinematic differential Global Positioning System (DGPS) has been widely used in dynamic displacement measurements of civil engineering structures. In recent years, interest has increased for Precise Point Positioning (PPP) due to its capability to generate positioning solutions as accurate as DGPS. In this study, the potential of post-processed kinematic PPP in terms of monitoring dynamic displacement response of a structure has been explored based on free damped oscillation events obtained from a model structure, which is able to vibrate in the fundamental and higher modes of vibration. A number of experiments have been carried out and five events, each of which is different character, have been selected to compare PPP results with DPGS results in the time and frequency domain. The results clearly demonstrate that the PPP method, like the DGPS method, offers great potential for the measurement of horizontal and vertical dynamic movement of structures. The impact of a short period (one minute) of observation length on the result of the kinematic PPP method was also investigated in terms of sensing the dynamic movement of a structure. Twenty selected one-minute data-sets extracted from a one-hour original data-set were processed by Canadian spatial reference system PPP and each one-minute PPP solution was compared with the corresponding segment obtained from the one-hour PPP solution. The results show that the one-minute PPP solution is able to extract the fundamental natural frequency of the oscillation in the horizontal and vertical component just like the one-hour PPP solution after the offset is removed and the lower frequency trend component is filtered out.