Transmission Scheduling for Multi-Hop Power Line Communication Networks

Although Power Line Communication (PLC) is not a new technology, its use to support data transmission over low voltage (LV) distribution networks is still the focus of ongoing research. This thesis focuses on the channel modelling and performance evaluation of narrowband (NB) PLC system. First, the channel modelling approaches of PLC are studied. Then, the proposed PLC channel modelling method based on the bottom-up approach for LV narrowband PLC in a frequency band between 9 kHz and 490 kHz is presented. This proposed model employs the transmission and scattering matrix methods to calculate the transfer function of a typical LV PLC network which comprises two common cable types (copper cables and aluminium conductor steel reinforced). Unlike the top-down approaches, this model is scalable as the network complexity increases and can better describe the network behaviour as a function of physical parameters.In addition, the noise characteristics and popular noise reduction techniques of PLC are studied. The major impairment to the PLC is the impulsive noise which is mainly generated by the switching transient in the network. Hence, a new technique is proposed to mitigate the impact of impulsive noise on data transmission over power lines. This proposed technique is an optimal Clipping/Blanking nonlinearity technique which is based on the minimum bit error rate (BER) search. Results obtained from the simulation of this technique demonstrate that performance has been enhanced in the NB-PLC system. The performance of the narrowband PLC system is also evaluated in both physical (PHY) and medium access control (MAC) layers. Since Orthogonal Frequency Division Multiplexing (OFDM) is a suitable modulation scheme for hostile environment of the power line, it is used to evaluate the PHY layer performance. As a result of the PHY layer performance analyses, it is found that the BER performance between neighbouring points in the typical LV PLC network is reasonable, but communication beyond one hop have to rely on upper layer protocols. In the MAC layer performance evaluation of the PLC system, the widely known random access MAC protocol that uses the Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) will be utilised. The MAC performance evaluation of the PLC system demonstrates a significant packet loss in LV PLC network even with a light traffic condition due to the noisy channel. Furthermore, the goodput declines abruptly once the individual transmission rate is high enough to block the network. In addition, the simulation results show that the channel errors can be reduced by adjusting the MAC parameters to allow the re-transmissions mechanisms to recoup the lost packets.

Today, and especially in the future, there is an increasing need for complementary techniques to meet the growing capacity requirements of wireless communications. A high data rate connection with power line communication (PLC) is one attractive solution to achieve this need. One way to improve the data rates obtained in PLC networks is to increase the used bandwidth and operate at higher frequencies. At the same time, however, it should be kept in mind that the power lines, unfortunately, act as quite good antennas which can detect strong near-by FM and TV signals. In the future, the PLC frequency range can overlap with the broadcasting frequency bands resulting in interference for these transmissions and vice versa. With the static notching the whole FM-frequency band is notched during the PLC communication. This may result in inefficient spectrum utilization as in a given place and at a given time only a part of the FM-frequency band may be occupied. In this paper, a blind spectrum sensing algorithm based on forward consecutive mean excision (FCME) algorithm is proposed to locate the free frequency bands inside the broadcasting frequency range in PLC-network. The performance of this sensing algorithm is analyzed using spectrum analyzer measurement results and calculations in the broadcasting frequency range. The results verify that the proposed method performs well when detecting free frequency bands in broadcasting frequency band providing means for better spectrum utilization in PLC-network.

As one of the most promising networking technologies, power-line communication (PLC) networks have been gradually used not only in home networking systems but also in industrial IoT (Internet of things). Current studies of PLC medium access control (MAC) protocol (i.e., IEEE 1901) only focus on the single-hop environment; however, in practical industrial IoT and home access communication systems, PLC networks generally utilize a multi-hop architecture. In addition, due to the difference in the MAC standard between 802 series and 1901, existing analytical models of multi-hop IEEE 802.11 wireless networks are not suitable for multi-hop IEEE 1901 PLC networks. In this paper, we propose a theoretical model for performance analysis of multi-hop IEEE 1901 PLC networks, where the impacts of traffic rate (containing relay traffic), buffer size, deferral counter process of 1901, hidden terminal problem and multi-hop environment are comprehensively considered. The modeling process is divided into two parts. In the local modeling part, we construct a brand-new Markov chain model to investigate the carrier sense multiple access with collision avoidance process of IEEE 1901 protocol under the multi-hop environment. In the coupling queueing modeling part, we employ queueing theory to analyze the packet transmission procedure between successive hops. On the basis, we derive the closed-form expressions of throughput, medium access delay, packet blocking probability, end-to-end successful transmission delay and goodput. Through extensive simulations, we verify that our theoretical model can accurately estimate the MAC performance of IEEE 1901 PLC networks in the multi-hop environment.

In order to improve the coverage and reliability of the information perception layer of the power Internet of things, a method of constructing a cross layer fusion network of low-voltage power line and micro-power wireless communication (CPW) is proposed. Firstly, a unified medium access control (MAC) layer model of CPW is established to provide basic support for realizing the integration of CPW network layers; then an improved ant colony algorithm combining Brownian motion and local convergence times control is proposed to complete the networking process of CPW; Distribute the sub-service flow of CPW, and propose the bit error rate requirement factor in the service distribution, and accomplish the cross-layer integration of low-voltage power line and micro-power wireless communication network. The simulation results show that the communication link service quality of the cross-layer fusion network is better than that of the power line and wireless dual-mode or cascaded communication networks. The communication efficiency of CPW is improved to 398.20kbits/s. The coverage of the power line and wireless communication fusion network can be expanded by setting corresponding bit error rate demand factors according to different services. It takes into account the balance of communication link quality and network load.

There is a need to fulfill the growing capacity requirements of power line communication (PLC). One way to achieve higher data rates in PLC networks is to operate at higher frequencies and increase the used bandwidth. In the future, the increased PLC frequency range can overlap with several wireless communications systems resulting in interference for these transmissions and vice versa. Commonly used static notching results in inefficient spectrum utilization as in a given place and at a given time only a part of the frequency range may be occupied by other wireless systems. Some wireless signals like FM signals are very closely spaced. In practice it is impossible to utilize these narrowband unoccupied frequency bands. In this case we can cluster closely spaced signals. Guard bands around detected wireless signals must also be taken into account before defining usable frequency bands for PLC. In this paper, we use the 2-D LAD ACC algorithm to detect and cluster interfering signals. We also further develop the algorithm so that after clustering guard bands are added and reclustering, if necessary, is executed. The performance of this modified 2-D LAD ACC algorithm is analyzed using calculations and spectrum analyzer measurement results obtained from in-office PLC network in the frequency range 80–200 MHz. The results verify that the proposed method performs well by detecting and clustering continuous and non-continuous wireless signals and providing means for clever spectrum utilization in PLC-network.

The hybrid wireless and power line communication (PLC) technology greatly improves the reliability of Power Internet of Things network (IoT) and the access ability of the terminals. However, with the development of Power IoT, the topology structure of the network becomes exceedingly complex, and the difficulty of networking is also gradually increasing. To address this issue, this paper proposes a multi-ant colony (MACS) based QoS networking algorithm for hybrid PLC and wireless communication networks. Considering the network QoS parameters and service demands, the networking algorithm constructs the fitness function to evaluate the quality of communication transmission paths, and the MACS algorithm is employed to establish the optimal relay route to complete networking. Numerical results prove that the MACS algorithm has a superior ability to jump out of local optimum than the traditional improved ant colony system (IACS) algorithm. Moreover, our proposed algorithm can construct the optimal relay route under corresponding constraints and demands according to different types of services.

Exponential demand for broadband applications has elicited renewed interest in characterizing noise in power line communication (PLC) networks for optimal error performance analysis. PLC is economical and ubiquitous, however due to multipath phenomena and nonstationary impulsive noise, the PLC channel is very harsh to signal transmission. Recent studies reveal that PLC noise is cyclostationary and modelling its characteristic should exploit the spectral and temporal redundancy. In addition, preliminary research shows that PLC noise exhibits self-similarity and can be predicted by fractal theory. In modelling noise employing fractal theory, the Hausdorff dimension (D) needs to be approximated. D is related to Hurst parameter (H), which is a measure of self-similarity. Hence, it is important to estimate H for accurate noise prediction using fractal theory. H parameter estimators assume stationarity in time series data. Therefore, preprocessing is required for the case of PLC noise before estimating H to make it stationary as periodicity and nonstatioanrity affects the H estimators. In this study, we remove the periodicity hidden in the PLC noise obtained from measurement campaign within several university offices, workshops and laboratories. Then long-range dependence is estimated from this pre-processed noise data by employing three estimation algorithms: R/S (rescaled adjusted range) method, aggregated variance method and absolute values of aggregated series method. Results from the said estimation methods though not the same, show that the Hurst parameters obtained from various noise measurements are greater than 0.5, implying presence of self-similarity with long-term memory. Results from this study will find valuable applications in PLC noise modelling using fractal and chaos theory and in error performance analysis in both narrowband and broadband PLC systems.

Powerline communication (PLC) provides inexpensive, secure and high speed network connectivity, by leveraging the existing power distribution networks inside the buildings. While PLC technology has the potential to improve connectivity and is considered a key enabler for sensing, control, and automation applications in enterprises, it has been mainly deployed for improving connectivity in homes. Deploying PLCs in enterprises is more challenging since the power distribution network is more complex as compared to homes. Moreover, existing PLC technologies such as HomePlug AV have not been designed for and evaluated in enterprise deployments. To this end, we give guidlines for designing PLC networks for providing ubiquitous connectivity in enterprises, based on measurement study of PLC performance in enterprise settings using commodity HomePlug AV PLC devices. Based on our findings, we propose that careful planning of PLC network topology, routing and spectrum sharing can significantly boost performance of enterprise PLC networks.

Power Line Communications have been the subject of an important research work. At the same time, the growing demand for multimedia communications provides a good prospect for PLC as a promising transmission technique for the “last mile” access network. Orthogonal Frequency Division Multiplexing (OFDM) is a spectrally efficient multicarrier modulation technique for high speed data transmission over multipath fading channels. High Peak-to-Average Power Ratio (PAPR) is a major drawback of OFDM. The high PAR of the OFDM signal has to be considered when setting the range of the digital-to-analog converter (DAC) and dimensioning the line-driver. This paper introduced an improved PAPR reduction scheme using constant envelope modulation. Furthermore, by utilizing continuous phase modulation (CPM) in a CE-OFDM system, the PAPR can be effectively reduced to 0 dB. The paper describes a CE-OFDM based modem for Power Line Communications (PLC) over the low voltage distribution network. Relying on a preliminary characterization of a PLC network, a complete description of the modem is given.

Power-line communication (PLC) networks have been increasingly used for constructing industrial IoT (internet of things) and home networking systems due to their low-cost installation and broad coverage feature. To guarantee the transmission reliability, ARQ (automatic repeat request) scheme is introduced into the link layer of reliable PLC networks, which allows the retransmission of a data frame several times so that it has a higher probability to be correctly received. However, current studies of performance analysis for PLC MAC (medium access control) protocol (i.e., IEEE 1901) do not take into account of the impact of ARQ scheme. To resolve this problem, we propose an analytical model to investigate the MAC performance of IEEE 1901 protocol for reliable PLC networks with ARQ scheme. In the modeling process, we first establish a PLC channel model to reflect the impacts of PLC channel types (containing Rayleigh fading and Log-normal fading), additive non-Gaussian noise feature and ARQ scheme on data transmission at link layer. Next, we employ Renewal theory and Queueing dynamics to capture the transmission attempt behavior of executing IEEE 1901 protocol in the unsaturated environment with finite transit buffer size. On the basis of combining these two models, we derive the closed-form expressions of 1901 MAC metrics considering the influence of the ARQ scheme. Furthermore, we prove that the proposed analytical model has the convergence property. Finally, we evaluate the MAC performance of 1901 protocol for reliable PLC networks with ARQ scheme and verify the proposed analytical model.

Power line communication (PLC) over low-voltage grid, is an attractive technology for no-new-wiring networks. In such typical application fields as home networks and street lighting management system, PLC network is always vulnerable in robustness and the logical link is liable to be destroyed because of the different user's personalities and the special channel properties. To improve the robustness of PLC network, the reasons that lead to the failure of data link are revealed, and the main achievements of randomized initialization protocols for ad hoc networks are studied. According to the study results, a novel low cost intelligent control method in MAC protocol is proposed to automatically maintain the logical connectivity of the PLC network. The performance of the method is evaluated theoretically and experimentally.

Power line communication (PLC) technology has created a niche use in the Internet of Things (IoT) by offering flexible and reliable connection among power-driven IoT devices/sensors over existing wired networks. In IoT over PLC networks, massive real-time data generated by the ever-growing connected devices will eventually pose an overwhelming burden on the IoT cloud, which in turn severely degrades the network performance. To cope with these issues, edge computing (EC) has emerged as a complement to cloud computing, aiming at offloading a portion of computing in the cloud to the network edges closer to the IoT devices. However, confronting a practical scenario that some electrical devices cannot communicate with wireless and mobile networks directly, existing EC paradigms may not be directly applied to IoT over PLC networks. In this paper, we propose a novel EC-IoT over PLC paradigm to reduce the transmission latency while migrating a portion of computing from the cloud to the edges. First, we develop a distributed EC platform to serve terminal users (TUs) in different IoT systems with various IoT services. Second, we put forth a cache-enabled scheme to store the popular contents from the cloud and edge sensors to reduce redundant data transmissions between TUs and the cloud. Finally, our experimental results demonstrate that the proposed EC-IoT over PLC network can significantly reduce energy consumption and transmission latency.

Power Line Communications (PLC) is regarded as the promising home networking technology for smart grid application since the PLC technology enables data transmission via the existing power line. The cooperation between PLC and Wireless Local Area Network (WLAN) will be an effective hybrid solution for Home Area Networks (HANs). In this paper, we consider that Transmission Control Protocol (TCP) packets are transmitting in heterogenous communications network based on PLC and WLAN. The existing TCP congestion control has low effectiveness due to the error-prone power line channel. Therefore, we propose an adaptive rate control to improve TCP performance in the hybrid PLC/WLAN HANs. We exploit the communications mechanism of WLAN to improve the PLC link utilization. The methodology of Heuristic Dynamic Programming (HDP) is employed to obtain the optimal rate policy. The bottleneck link capacity is estimated by neural network training. The sending rate is adapted according to the long-term quality of service (QoS) of applications. Simulation results illustrate that the proposed rate control effectively filters out the negative impact from the instantaneous impulse noise in PLC channel and outperforms the existing TCP.

With the onset of multimedia applications, Quality of Service (QoS) in 802.11-based wireless ad hoc networks has been an essential area to look into. Standard wireless protocols such as IEEE 802.11b and IEEE 802.11e have been deemed unsuitable for multimedia traffic transmission in an ad hoc (multihop) network environment due to the unique network characteristics. As an ad hoc network is infrastructureless and distributed in nature, it gives rise to several challenges in QoS provisioning. In this thesis, we focus on the research of three key areas on QoS in ad hoc networks namely, buffer management in the medium access control (MAC) layer, cross-layer design and flow admission control. Firstly, we study MAC layer buffer management in the IEEE 802.11e protocol. The IEEE 802.11e MAC protocol provides QoS for multimedia traffic by probabilistic priority queueing. Ad hoc networks tend to generate a large volume of network control packets for route maintenance and these control packets are typically queued in the highest priority queue. As a result, higher priority control traffic is always being served, consuming most of the bandwidth and results in poor network performance for data traffic. We examine this problem and propose a dynamic buffer management scheme to mitigate it. By setting different threshold levels in different priority queues, we allow lower priority data traffic to be served when the higher priority control traffic is deemed to be excessive. Simulation of our proposed scheme has shown that our approach yielded better network performance compared to the standard protocol in terms of packet delivery ratio and average delay. Secondly, we study the cross-layer interaction between the MAC and Network layers to identify its impact on QoS. We select the IEEE 802.11e MAC protocol and Ad-hoc On Demand Distance Vector (AODV) routing protocol in our study since they are standardized protocols for wireless networks. In IEEE 802.11e MAC protocol, lower priority traffic has a higher probability of being blocked. Hence, the MAC layer will inform the Network layer of a broken link through the link notification function. In this case, AODV will re-route the paths that traverse this link. As a result, higher priority traffic which shares the same link as the lower priority traffic will undergo the same re-routing procedures. We termed this phenomenon path correlation effect. Under high traffic load, the path correlation effect will be more intense and hence degrade the QoS of higher priority traffic. To break the path correlation effect, we propose a cross-layer design called the Bundled Virtual Circuit (BVC). Our proposed BVC scheme not only addresses the path correlation issues, but also provides priority treatment from the Network layer to the MAC layer. Through our simulations, our proposed cross-layer design approach is proven to provide better network performance than the 802.11e/AODV protocols in terms of packet delivery ratio and delay. Finally, we examine flow admission control at the routing layer in ad hoc networks. Standard routing protocols such as AODV performs routing on a shortest path basis. In the presence of multiple routes, hotspots are likely to form among the intermediate nodes and thus lead to network congestion. In addition, existing routes are not well-protected from the introduction of new routes. We propose a flow admission control algorithm to be used with AODV. Our algorithm allows routes to be created through available bandwidth and congestion estimation. During the route discovery phase, each node will be gauged on its estimated available bandwidth and its backlog of packets in the MAC buffer. If a node does not have sufficient bandwidth, or has too many backlogged packets compared to the requested flow rate, it will not participate in the route discovery process. From simulations, our new scheme is able to provide better network performance than the standard AODV protocol in terms of delay. Our work in this thesis focuses on QoS provisioning in ad hoc networks from the MAC and network layer perspectives. By studying the network characteristics and protocols’ behavior, we investigate the various problems of providing QoS in an ad hoc network environment and propose three different schemes to improve the QoS provisioning at the MAC and network layers. We believe that our work is able to provide some insights to the research area on QoS in ad hoc networks.

The reliability and distance of Power Line Communication (PLC) are the most important factors, which limit the application of PLC in practice seriously. This paper discusses the specialties and the methods of building up the PLC networks, uses an improved Dynamic Ant Colony System algorithm (DACS) in dynamic routing of PLC networks, and the multi-path storage technology is given. The improved DACS enhanced the accuracy and efficiency of dynamic routing in two aspects, that is the best tours and the worst tours. A dynamic penalty on worst tours will open up chances for ants to navigate, limit intentions and provide cautions in an ant's decision to move. And ants can get better search guidance by concentrating only the best tours from all groups. The simulation and experimentation indicate that the improved DACS provides an effective dynamic routing method for the expansion of PLC. It is an effective method of improving the reliability of PLC.