- Research Article
29
- 10.1016/0360-5442(91)90089-5
Summary of Gas-Cooled reactor programs
- Jan 01, 1991
- Energy
- A.J Goodjohn
Summary of Gas-Cooled reactor programs
For several years, the United States and the Federal Republic of Germany (FRG) have engaged in a successful cooperative program to develop high temperature gas-cooled reactor (HTGR) fuel cycle technology. Recent tests in reprocessing pilot plant facilities at General Atomic Company have demonstrated the feasibility of performing HTGR head-end unit operations for both spherical (German) and block-type (American) fuel elements in a single process line. Because of an unexpected high fines generation and elutriation rate, extended fluidized bed primary burning of FRG fuel material was impossible to accomplish with the burner system and operating procedures optimized for U.S. fuel burning. Operational modification, including startup with a carbon-poor bed and reduction of the fluid-izing velocity, resulted in dramatic improvements in FRG fuel-burning behavior and allowed extended processing campaigns. Additional modifications to the fines recycle system and burner are recommended to optimize the system for processing of FRG fuels.
Summary of Gas-Cooled reactor programs
Summary of Gas-Cooled reactor programs
Authors
Authors
Preparation of SiC Composite Coating on the Surface of Graphite Spheres in VHTR
Due to various characteristics such as high thermal efficiency, inherent safety, passive safety, and hydrogen production for industrial use, the high temperature gas-cooled reactor (HTR) is considered as one of the most promising technologies in the future. Fuel elements are the core part of a reactor. In the existing high-temperature gas cooled reactor HTR, spherical fuel elements are involved, with graphite accounting for more than 90% of the mass and volume of the fuel element. However, graphite is prone to oxidation in oxidizing atmospheres at a higher temperature than 400°C. Regarding the design of future HTR, accident conditions must be taken into consideration. Under the accident conditions of inlet and outlet water, the graphite in the spherical fuel element is easy to be oxidized. This causes damage to the fuel elements and increases the release of fission products, which threatens the safety of HTR. In this study, two-step pack cementation is performed to prepare SiC composite coatings on the surface of graphite spheres with a diameter of 40 mm, which improves the oxidation resistance of graphite spheres. According to research, the thickness of coating is about 150 μm after two-step pack cementation, with SiC and Si as the main phase of the coating. However, it is necessary to improve the density of SiC composite coatings needs. After 7 h of oxidation in static air at 1500°C, the mass loss reaches 22.22%. To a certain extent, the compactness of the coating can be improved by the slurry impregnation and Si sol gel method.
Read moreAnalysis of DLOFC Accident in HTR-10 Operating at Higher Temperatures
The high-temperature gas-cooled reactor (HTGR) with a high outlet temperature from 700°C to 800°C to 1000°C is expected to be widely used for heat supply, hydrogen production, steelmaking, seawater desalination, thermal recovery of heavy oil, and coal liquefaction and gasification. The 10-MW High Temperature gas-cooled test Reactor (HTR-10), with an outlet temperature of 700°C, has been constructed and operated in China as a pilot plant to demonstrate the inherent safety features of the modular HTGR. Supported by the Chinese National S&T Major Project and National Key R&D Program of China, some research on HTGR technology with much higher outlet temperatures has been carried out in the Institute of Nuclear and New Energy Technology (INET), Tsinghua University, China, including the preliminary design and analysis of a HTR-10 with an outlet helium temperature of 950°C (HTR-10H). This paper presents the simulation results of the depressurized loss-of-forced cooling (DLOFC) accident of the HTR-10H. This analysis was performed with two different codes, TINTE and SPECTRA, within a cooperation between the Nuclear Research Group of the Netherlands and the INET. In the past, comparisons between TINTE and SPECTRA have also been performed for the Chinese 200-MW(electric) High Temperature gas-cooled Reactor Pebble bed Module (HTR-PM). The calculation results showed that both the fuel temperature and the reactor pressure vessel temperature remained below the acceptable limits during the DLOFC accident. The inherent safety of the HTR-10 can be guaranteed in the accident condition. Both the TINTE results and SPECTRA results for the maximum and average fuel temperature agreed well. In both models, the heat carrying capacity of the Reactor cavity cooling system (RCCS) had been underestimated, especially in the SPECTRA model. The RCCS performance needs to be investigated and the models need to be further improved in the future. The work introduced in this paper shows the feasibility of increasing the outlet helium temperature of the HTR-10 from the current 700°C to 950°C, if further design optimization can effectively reduce the fuel temperature during steady-state operation, or more irradiation tests can be carried out to prove the retention performance of the TRISO particles for the radioactive fission products at temperatures above 1200°C.
Read more1170 MW/sub t/ HTGR steamer cogeneration plant: design and cost study
A conceptual design and cost study is presented for intermediate size high temperature gas-cooled reactor (HTGR) for industrial energy applications performed by United Engineers and Constructors Inc., (UE and C) and The General Atomic Company (GAC). The study is part of a program at ORNL and has the objective to provide support in the evaluation of the technical and economic feasibility of a single unit 1170 MW/sub t/ HTGR steam cycle cogeneration plant (referred to as the Steamer plant) for the production of industrial process energy. Inherent in the achievement of this objective, it was essential to perform a number of basic tasks such as the development of plant concept, capital cost estimate, project schedule and annual operation and maintenance (O and M) cost.
Read moreSiC/SiO<sub>2</sub> Coating on Matrix Graphite Spheres of HTR Fuel Element Produced by a Two-Step Pack Cementation/High-Temperature Oxidation Process
Graphite is one of the most important material for the reactor core and fuel elements of high temperature gas-cooled reactor (HTR). Improving the oxidation resistance of graphite is very essential for the research of new fuel elements and the development of HTR. In this study, a gradient SiC layer of 500~700 μm was prepared on matrix graphite spheres by a two-step pack cementation, and the outer SiO2 layer prepared by the high-temperature oxidation process. The phases, microstructure, bonding strength and oxidation resistance of SiC/SiO2 coated matrix graphite spheres were investigated. The SiC/SiO2 coated matrix graphite spheres were carried on rapid thermal shocking tests from 1773 K to room temperature for 50 times without any cracks. The SiC/SiO2 coated matrix graphite spheres exhibits excellent anti-oxidation properties. No obvious weight loss was found after isothermal oxidation in air at 1273 K for 50 h and the weight gain was less than 1% at 1773 K in air for 50 h due to the oxidation of SiC layer.
Read moreMethodology Development for Transient Flow Distribution Analysis in High Temperature Gas-Cooled Reactor
In the thermal hydraulic design of the prismatic-type of the high temperature gas cooled reactor (HTGR), unintended flows such as gap flows between columns, cross flows between column layers and gap flows between permanent reflectors should be analyzed to minimizing the unintended flows. The flow distribution considering unintended flows in the reactor has been evaluated for steady and conservative condition. On the other hand, the transient thermal hydraulic analysis for satisfactorily realistic conditions will be helpful for the design improvement of prismatic-type HTGR. The present study aims to improve the thermal hydraulic system analysis code developed by Japan Atomic Energy Agency based on the RELAP5/MOD3 code and confirm its applicability for the transient flow distribution analysis for prismatic-type HTGRs during anticipated operational occurrences and accidents for its design improvement utilizing experiences on high temperature engineering test reactor (HTTR) design. The calculation model and code were developed and validated to evaluate the detailed flowrate distribution considering the unintended flows in the core and the molecular diffusion that is important to analyze beginning air ingress behavior in an air ingress accident triggered by a rupture of a primary coolant piping in HTGR. It is concluded that a prospect has confirmed to apply the improved thermal hydraulic system analysis code for transient flow distribution analysis for prismatic-type HTGRs.
Read morePreliminary Study on Features of Key Components for HTGR Helium Turbine System
High temperature gas cooled reactor (HTGR) is featured by inherent safety. With high outlet temperature, HTGR is of potentially economical competitiveness. Helium turbine system can take advantage of high temperature helium to achieve high efficiency as well as compact structure, with development perspective. Key components of HTGR helium turbine system include rotary machinery such as turbo compressor and motor/generator, and heat transfer components (i.e. precooler, intercooler, recuperator and nuclear reactor). Due to the closed cycle, the features of key components are not independent. This paper preliminary explores the inherent relationships among features of key components, especially changing with reactor power. For heat transfer components, the general relationship between pressure drop and the effectiveness of heat transfer is analyzed. Furthermore, it is found that the pressure drop in recuperator, precooler and inter-cooler depends on the reactor power with engineering constraints. Besides, There exists the approximate squared relation between power and pressure drop in heat exchangers. For rotary machinery, it is found that the moment of inertia is the function of reactor power. For example, the moment of inertia of motor/generator is proportional to the reactor power. The relationship between moment of inertia of turbo-compressors and reactor power is more complex. This study is expected to be helpful to the design of key components for HTGR helium turbine system and can be applied to analyze the cycle’s dynamic characteristics.
Read morePredicted nuclear heating and temperatures in gas-cooled nuclear reactors for process heat applications
The high-temperature gas-cooled nuclear reactor (HTGR) is an attractive potential source of primary energy for many industrial and chemical process applications. Significant modification of current HTGR core design will be required to achieve the required elevations in exit gas temperatures without exceeding the maximum allowable temperature limits for the fuel material. A preliminary evaluation of the effects of various proposed design modifications by predicting the resulting fuel and gas temperatures with computer calculational modeling techniques is reported. The design modifications evaluated are generally those proposed by the General Atomic Company (GAC), a manufacturer of HTGRs, and some developed at the LASL. The GAC modifications do result in predicted fuel and exit gas temperatures which meet the proposed design objectives. (auth)
Read morePre-conceptual high temperature gas-cooled microreactor design utilizing two-phase composite moderators. Part I: Microreactor design and reactor performance
Pre-conceptual high temperature gas-cooled microreactor design utilizing two-phase composite moderators. Part I: Microreactor design and reactor performance
Read moreCost Analysis of Nuclear Hydrogen Production Using IAEA-HEEP 4 Software
Hydrogen is a commercially important element. Basically, there are several methods of hydrogen production that have been commercially used, such as Steam Methane Reforming (SMR), High Temperature Steam Electrolysis (HTSE), and thermochemical cycles, like Sulphur-Iodine (SI). Among these methods, SMR is the most widely used for large-scale hydrogen production, with conversion efficiency between 74–85% and it has commercially used in some fertilizer industries in Indonesia. Steam reforming is a method to convert alkane (natural gas) compounds to hydrogen and carbon dioxide (synthetic gas) by adding moisture at high pressure and temperature (35-40 bar; 800-900°C). These hydrogen production technologies can be coupled with different nuclear reactors based on the heat required in the process. The High Temperature Gas-cooled Reactor (HTGR) using helium as a coolant, has a high outlet temperature (900°C), so it can potentially be used to supply for process heat for hydrogen production, coal liquefaction/gasification or for other industrial processes requiring high temperature heat. Hydrogen production cost from SMR method is influenced by a range of technical and economic factors. The fuel component of natural gas needed in the SMR method can be replaced by nuclear heat from a nuclear power plant (NPP) operating in cogeneration mode (i.e. simultaneous producing electric power and heat), hence contributing to the reduction of carbon dioxide in the process.In the SMR method, fuel costs are the largest cost component, accounting for between 45% and 75% of production costs. Therefore, there is opportune to assess the economics of hydrogen production by using nuclear heat. The economic evaluation is done by using IAEA HEEP-4 Software.The results comprise cost break up for 2 cases, coupling SMR process for hydrogen production with: (1) 2 HTGRs of 170 MWth/unit; and (2) 1 HTGR of 600 MWth/unit. The cost of hydrogen production is highly depend on the scale of the NPP as energy source and results indicated that hydrogen production cost of the 1 HTGR Unit600 MWth (Case 2) has a lower value (1.72 US$/kgH2), than the cost obtained when 2 HTGR units of 170 MWth each (case 1) are considered (2.72 US$/kgH2). For comparison, the hydrogen production cost by using SMR with carbon capture and storage (CCS) with natural gas as fuel is 2.27 US$/kgH2.
Read moreStudy on Operation Scenario of Tritium Production for a Fusion Reactor Using a High Temperature Gas-Cooled Reactor
To start up a fusion reactor, it is necessary to provide a sufficient amount of tritium from an external device. The fusion DEMO reactor is planned to start up in the 2030s. Herein, methods for supplying the reactor with tritium are discussed. For the initial startup of the fusion reactor, use of a high temperature gas-cooled reactor (HTGR) as a tritium production device has been proposed. So far, the analyses have been focused only on the operation in which fuel is exchanged at stated periods (batch) using the block type HTGR. In this paper, to improve the performance of tritium production, properties of the HTGR are studied from the viewpoint of continuous operation for several conditions. In continuous operation, for example, in the pebble bed type HTGR, it is possible to design an operation that has no time loss for refueling. The pebble bed modular reactor (PBMR) and the gas turbine high temperature reactor of 300 MWe nominal capacity (GTHTR300) are assumed as the calculation and comparison targets, and simulation is made using the continuous-energy Monte Carlo transport code MVP-BURN. It is shown that the continuous operation using the pebble bed type HTGR has almost the same tritium productivity compared with the batch operation using the block type HGTR. The issues for pebble bed type HTGR as a tritium production device are discussed.
Read moreProgressive Development for Structural Integrity Quantification of Nuclear Grade Graphite in Very High Temperature Gas Cooled Reactor Core Environments
Graphite is used as a moderator for high temperature gas-cooled reactor (HTGR) because the microstructure ofwithin the graphite can store defect energy (Wigner energy) induced by high-doses radiation. However, typically, there are temperature spikes associated with the random releases of enormous amount of defect energy. The irregular events of temperature spikes subsequently heat up HTGR and risk the HTGR experiencing beyond the designed-limit temperature limitsof HTGR. To further investigate the graphite-microstructure evolution subject to radiation damage, we develop a progressive method. We quantify the structural integrity of nuclear-grade graphite using High-resolution Transmission Electron Microscopy (HRTEM). In this study, the nuclear-grade graphite was first radiated by ion implantation with 3Mev C2+ to simulate the material in a very-high-temperature-gas-cooled-reactor (VHTGR)-core environment. The temperatures were controlled in the ranges of 500~1000oC. After the artificial irradiation, HRTEM analyses were proceeded to quantify the microstructure evolution and we calculated the stored energy within the microstructure of the radiated nuclear-grade graphite via Fast Fourier Transform of HRTEM images. Our results show that, at 600 oC and 3 dpa, the microstructure can store energy up to 136 (cal/g), which can heat the HTGR up to 345 oC.
Read moreComparison of US/FRG accident condition fuel failure and release models
Although there are many differences between the High-Temperature Gas Cooled Reactor (HTGR) concepts being developed in the US and the High Temperature Reactor (HTR) concepts in the Federal Republic of Germany (FRG), the coated fuel particles are very similar. Significant benefits are achievable through cooperative research and exchange of information and data on the fuel performance and radionuclide retention in the coated fuel particles. This draft report describes cooperative work on HTGR safety research as agreed to in the "USA/FRG Umbrella Agreement for Cooperation in GCR Development: Safety Research Subprogram Plan," specifically, this work was conducted under Project Work Statement (PWS) S-6 titled "Fission Product Retention in Fuel," 9 refs., 12 figs., 4 tabs.
Read moreDiffusion Welding of Alloys for Molten Salt Service - Status Report
The present work is concerned with heat exchanger development for molten salt service, including the proposed molten salt reactor (MSR), a homogeneous reactor in which the fuel is dissolved in a circulating fluid of molten salt. It is an outgrowth of recent work done under the Next Generation Nuclear Plant (NGNP) program; what the two reactor systems have in common is an inherently safe nuclear plant with a high outlet temperature that is useful for process heat as well as more conventional generation The NGNP program was tasked with investigating the application of a new generation of nuclear power plants to a variety of energy needs. One baseline reactor design for this program is a high temperature, gas-cooled reactor (HTGR), which provides many options for energy use. These might include the conventional Rankine cycle (steam turbine) generation of electricity, but also other methods: for example, Brayton cycle (gas turbine) electrical generation, and the direct use of the high temperatures characteristic of HTGR output for process heat in the chemical industry. Such process heat is currently generated by burning fossil fuels, and is a major contributor to the carbon footprint of the chemical and petrochemical industries. The HTGR, based on graphite fuel elements, can produce very high output temperatures; ideally, temperatures of 900 °C or even greater, which has significant energy advantages. Such temperatures are, of course, at the frontiers of materials limitations, at the upper end of the performance envelope of the metallic materials for which robust construction codes exist, and within the realm of ceramic materials, the fabrication and joining of which, on the scale of large energy systems, are at an earlier stage of development. A considerable amount of work was done in the diffusion welding of materials of interest for HTGR service with alloys such as 617 and 800H. The MSR output temperature is also materials limited, and is projected at about 700 °C. (RR E) A different set of alloys, such as Alloy N and 242, are needed to handle molten salts at this temperature. The diffusion welding development work described here builds on techniques developed during the NGNP work, as applied to these alloys. There is also the matter of dissimilar metal welding, since alloys suitable for salt service are generally not suited for service in gaseous oxidizing environments, and vice versa, and welding is required for the Class I boundaries in these systems, as identified in the relevant ASME codes.
Read more