The Dynamic Execution Integrity Engine (DExIE) is a lightweight hardware monitor that can be flexibly attached to many IoT-class processor pipelines. It is guaranteed to catch both inter- and intra-function illegal control flows in time to prevent any illegal instructions from touching memory. The performance impact of attaching DExIE to a core depends on the concrete pipeline structure. In some especially suitable cases, extending a processor with DExIE will have no performance penalty. DExIE is real-time capable, as it causes no or only up to 10.4 % additional and then predictable pipeline stalls. Depending on the monitored processor’s size and structure, DExIE is faster than software-based monitoring and often smaller than a separate guard processor. We present not just the hardware architecture, but also the automated programming flow, and discuss compact adaptable storage formats to hold fine-grained control flow information.

This paper describes a field-programmable gate array (FPGA) implementation of a fixed-point low-density lattice code (LDLC) decoder where the Gaussian mixture messages that are exchanged during the iterative decoding process are approximated to a single Gaussian. A detailed quantization study is first performed to find the minimum number of bits required for the fixed-point decoder to attain a frame error rate (FER) performance similar to floating-point. Then efficient numerical methods are devised to approximate the required non-linear functions. Finally, the paper presents a comparison of the performance of the different decoder architectures as well as a detailed analysis of the resource requirements and throughput trade-offs of the primary design blocks for the different architectures. A novel pipelined LDLC decoder architecture is proposed where resource re-utilization along with pipelining allows for a parallelism equivalent to 50 variable nodes on the target FPGA device. The pipelined architecture attains a throughput of 10.5 Msymbols/sec at a distance of 5 dB from capacity which is a 1.8times improvement in throughput compared to an implementation with 20 parallel variable nodes without pipelining. This implementation also achieves 24times improvement in throughput over a baseline serial decoder.

The SARS-CoV-2 virus causes a respiratory disease in humans, known as COVID-19. The confirmatory diagnostic of this disease occurs through the real-time reverse transcription and polymerase chain reaction test (RT-qPCR). However, the period of obtaining the results limits the application of the mass test. Thus, chest X-ray computed tomography (CT) images are analyzed to help diagnose the disease. However, during an outbreak of a disease that causes respiratory problems, radiologists may be overwhelmed with analyzing medical images. In the literature, some studies used feature extraction techniques based on CNNs, with classification models to identify COVID-19 and non-COVID-19. This work compare the performance of applying pre-trained CNNs in conjunction with classification methods based on machine learning algorithms. The main objective is to analyze the impact of the features extracted by CNNs, in the construction of models to classify COVID-19 and non-COVID-19. A SARS-CoV-2 CT data-set is used in experimental tests. The CNNs implemented are visual geometry group (VGG-16 and VGG-19), inception V3 (IV3), and EfficientNet-B0 (EB0). The classification methods were k-nearest neighbor (KNN), support vector machine (SVM), and explainable deep neural networks (xDNN). In the experiments, the best results were obtained by the EfficientNet model used to extract data and the SVM with an RBF kernel. This approach achieved an average performance of 0.9856 in the precision macro, 0.9853 in the sensitivity macro, 0.9853 in the specificity macro, and 0.9853 in the F1 score macro.

The scintillator detectors are recalibrated against the datasheet given by the manufacturer. Optimal and mutual dependent values of (a) high voltage at PMT (Photomultiplier Tube), (b) amplifier gain, (c) average time to count the radiation particles (set by operator), and (d) number of instances/sample number are estimated. Total 5: two versions of Central Limit Theorem (CLT), (3) industry preferred Pulse Width Saturation, (4) calibration based on MPPC coupled Gamma-ray detector, and (5) gross method are used. It is shown that the CLT method is the most optimal method to calibrate the detector and its respective electronics couple. An inverse modeling-based Computerized Tomography method is used for verification. It is shown that statistically averaging results are more accurate and precise data than mode and median if the data is not skewed and a random number of samples are used during the calibration process. It is also shown that the average time to count the radiation particle is the most important parameter affecting the optimal calibration setting for precision and accurate measurements of gamma radiation.

In this paper we deal with classification of anomalous data detected by the data reduction system of the Gaia space mission, in operation since 2013. Given the size and complexity of intermediate data and plots for diagnostics, beyond practical possibility of full human evaluation, the need for automated signal processing tools is becoming more and more relevant. Our classification task consists in discriminating among “normal” data and data affected by anomalies, which at present are grouped into four different classes. We investigate the use of some clever pre-processing approaches that allow the application of a tailored technique based on the Hough transform, and of some machine learning tools, evidencing that the task can be exactly solved in the former case. In the latter case, random forests and support vector machine provide less than satisfactory performance, while convolutional neural networks achieve very good classification accuracy, up to 91.22%. Statistics show satisfactory results also in terms of precision and recall of each class.

The world is witnessing a rising number of preterm infants who are at significant risk of medical conditions. These infants require continuous care in Neonatal Intensive Care Units (NICU). Medical parameters are continuously monitored in premature infants in the NICU using a set of wired, sticky electrodes attached to the body. Medical adhesives used on the electrodes can be harmful to the baby, causing skin injuries, discomfort, and irritation. In addition, respiration rate (RR) monitoring in the NICU faces challenges of accuracy and clinical quality because RR is extracted from electrocardiogram (ECG). This research paper presents a design and validation of a smart textile pressure sensor system that addresses the existing challenges of medical monitoring in NICU. We designed two e-textile, piezoresistive pressure sensors made of Velostat for noninvasive RR monitoring; one was hand-stitched on a mattress topper material, and the other was embroidered on a denim fabric using an industrial embroidery machine. We developed a data acquisition system for validation experiments conducted on a high-fidelity, programmable NICU baby mannequin. We designed a signal processing pipeline to convert raw time-series signals into parameters including RR, rise and fall time, and comparison metrics. The results of the experiments showed that the relative accuracies of hand-stitched sensors were 98.68 (top sensor) and 98.07 (bottom sensor), while the accuracies of embroidered sensors were 99.37 (left sensor) and 99.39 (right sensor) for the 60 BrPM test case. The presented prototype system shows promising results and demands more research on textile design, human factors, and human experimentation.

Due to melanoma is one of the skin cancers with the highest mortality rate and have a large amount of data during the collection and diagnosis, there is an urgent need to improve the diagnostic efficiency and accuracy. However, there remain problems in analyzing medical big data for skin lesion application, such as the intra-class variation and inter-class similarity in skin lesion images and the lacks of ability to focus on the lesion area affecting the classification results of the model. To address these dilemmas, in this paper, we proposed a novel machine learning-based approach that builds on top of DenseNet. It combines the attention mechanism and large margin loss to enhance the classification accuracy in terms of intra-class compactness and inter-class separability. We evaluated our model on ISIC 2017 (International Skin Imaging Collaboration) dataset, which has achieved 92% of Mean AUC. The experimental results show the effectiveness of our solution outperforms the state-of-the-art significantly in classify skin lesion and can accurately classify malignant melanoma on medical images.