While fused silica microlens arrays (MLAs) act as crucial components in the fields of infrared optics and laser systems, direct laser writing has been proposed for the fabrication of MLAs. However, the layer-by-layer slicing strategy generally leads to stepped surface textures formed on the microlens surface, resulting in high surface roughness and limited transmittance. This work proposes a temperature-controlled CO2 laser polishing method for the fabrication and subsequent smoothing of fused silica microlens arrays. Specifically, an infrared temperature measurement system is integrated into a CO2 laser direct writing platform. Correspondingly, a proportional-integral-derivative algorithm is used to adjust the laser power in real time based on the temperature deviation at the processing spot, thus maintaining the polishing zone in a molten rather than vaporizing state. Furthermore, a finite element model of laser polishing of fused silica coupled with laser heating and fluid flow is developed, which is used to analyze the spatiotemporal evolution of the temperature field, as well as its correlation with the response of the processed surface. Experimental results show that temperature-controlled laser polishing reduces the surface roughness of the fabricated MLAs by 86.8%, while the transmittance in the visible band remains above 90%. This work provides a feasible closed-loop polishing method and a mechanistic analysis model for the laser polishing of fused silica MLAs.

Accurate permittivity characterization at terahertz frequencies is important for material analysis and device design, yet it remains challenging for small-volume samples and compact test structures. In this work, a terahertz permittivity sensor based on a spoof surface plasmon polariton (SSPPs) transmission line coupled to a backside split-ring resonator (SRR) is proposed and numerically studied. The SSPPs line is patterned on the top side of the substrate, while the SRR is etched on the backside, with the sample loaded into the SRR gap. The SSPPs mode penetrates through the substrate and excites the SRR, producing a pronounced transmission notch. Changes in the sample permittivity modulate the effective capacitance of the resonator, resulting in a monotonic shift in the notch center frequency. For relative permittivities from 1 to 8, the notch center frequency decreases from 152.1 GHz to 117.8 GHz, corresponding to a total shift of 34.3 GHz and an average sensitivity of about 4.90 GHz/εr. The minimum S21 remains within approximately −23.80 to −21.56 dB, while the Q-factor stays in the range of 94.33–108.23, indicating good spectral readability. Tolerance analysis further shows that the resonance frequency is sensitive to critical structural dimensions and layer alignment, and practical implementation is therefore more suitable for single-device calibrated frequency-shift sensing. These results demonstrate the feasibility of the proposed dual-layer SSPPs–SRR configuration for compact permittivity sensing in the terahertz regime.

Compared with the conventional push-broom imaging mode, conical scanning extends the imaging swath through rotational scanning and is suitable for high-resolution, wide-swath remote sensing. To achieve continuous full-coverage imaging, the camera must be mounted at a certain tilt angle and employ an off-axis optical system with a sufficiently large field of view (FOV). However, the tilted installation causes nonuniform irradiance and increased off-axis distortion, while wide-field off-axis imaging also introduces radiometric consistency problems in focal-plane multi-detector stitching. To address these issues, this study investigates the optical design of a tilted off-axis camera for conical-scan imaging. Under the constraints of full coverage and swath requirements, key optical parameters were jointly determined, and a lightweight wide-coverage off-axis three-mirror system was designed, optimized, and evaluated. The final system has a focal length of 1545 mm, an F-number of 8.4, and a full FOV of 23.4° × 11.7°. The modulation transfer function is greater than 0.41 at the Nyquist frequency, and the maximum distortion is less than 2.5446%. In addition, for the focal-plane optical stitching structure, the coupled effects of local structural vignetting and global geometric vignetting induced by the tilted installation were analyzed. The results show that the gray-level difference in the adjacent detector overlap regions is only 0.31–0.53 digital numbers (DN), and the full focal plane shows a smooth gray-level attenuation rate of 5.39–6.77%. These results indicate that vignetting has no significant effect on focal-plane stitching. The proposed camera is well suited for conical-scan imaging.

Mode division multiplexing (MDM) is an emerging optical communication solution for high-capacity wired–wireless applications. Due to the presence of modal crosstalk and link impairments in MDM, this work aims to design a system that provides low complexity, an improved Shannon Capacity limit, and high spectral efficiency. In this work, a quad modal MDM system using an integrated parabolic index multimode fiber and free-space optics (PIMMF-FSO) link is presented. Four linearly polarized (LP) modes, LP01, LP22, LP03, and LP13 based on a 16 × 10 Gbps MDM system offering different sixteen channels, are realized. Results show that the system can sustain a 7.5 dB insertion loss over 100 m FSO and a 100 m fiber range for different LP modes under the impact of clear air, moderate haze, heavy rain and wet snow climates with weak turbulence. A faithful fiber range of 3000 m can be obtained successfully in the proposed system with a −10 dB link loss, −7.62 dBm received power and 10 dB noise. Compared to existing designs, the proposed design offers optimum performance in terms of high channel capacity and a high traffic rate with low complexity and high spectral efficiency. Additionally, high received power, with acceptable noise, link loss, FSO misalignments and fiber nonlinearities, is successfully obtained.

The transverse beam size is a key parameter for characterizing the performance of synchrotron radiation sources. Accurate measurement of the transverse beam size is crucial for assessing beam quality. In this study, a fiber array-photomultiplier tube (PMT) beam measurement system was developed to enable high-precision sampling of beam profile information for beam-size measurement. Furthermore, a hybrid method integrating nonlinear least squares (NLLS) fitting and Gaussian basis-function fitting was proposed to reconstruct the beam intensity profile from discrete sampling data. Before performing NLLS fitting, a median absolute deviation (MAD)-based threshold filter is employed to remove outliers and suppress random noise, thereby improving the stability and robustness of the parameter estimation. The filtered data are then fitted using NLLS to obtain the reconstructed distribution. To capture potential high-order modal features in the beam profile, a Gaussian basis-function fitting model was also introduced for comparison, and its performance was evaluated under complex intensity distributions. Additionally, the relationship between the full width at half maximum (FWHM) and beam intensity was experimentally verified while accounting for measurement effects in the system. The results demonstrate that the proposed hybrid algorithm improves reconstruction accuracy and robustness, enabling precise recovery of the beam-intensity profile in the fiber-array PMT system.

Precise control of optical intensity distributions is important for beam shaping, optical trapping, and optical potential engineering. We implement a digital micromirror device (DMD)-based programmable beam-shaping platform for generating high-fidelity optical intensity distributions with user-defined geometries. The approach combines precise system calibration, Fourier-plane spatial filtering via an optimized pinhole, and an iterative intensity feedback algorithm to transform imperfect Gaussian input beams into flat-top, lattice, and composite intensity distributions. The feedback loop typically converges within seven iterations, producing highly uniform flat-top profiles with 98.7% uniformity (corresponding to a root-mean-square error (RMSE) of 1.3%). Systematic studies identify the optimal Fourier-plane aperture that balances diffraction suppression with optical throughput. These results demonstrate a practical route to programmable beam shaping and optical intensity control.

We designed a kind of new vortex beam generator based on a planar all-dielectric metamaterial in the mid-infrared band. The height of this generator remains constant in the plane, and the effective refractive index increases gradually in the azimuthal direction which depends on subwavelength aperture columns with gradual diameters in the dielectric flat plate. Two types of vortex beam generators including transmissive- and reflective-type generators are designed where the thickness of the latter is half of the former. Simulation results show that both vortex beam generators successfully produce mid-infrared vortex beams with a topological charge number of one. This planar vortex beam generator based on a dielectric metamaterial has the advantages of simple structure, easy processing and low optical absorption.

Liquid crystals (LCs) occupy a distinctive position among functional optical materials, combining the fluidity of liquids with the long-range molecular order characteristic of crystalline solids [...]

Accurate absolute pressure measurement is of great importance in industrial control, environmental monitoring, and aerospace. Traditional fiber-optic Fabry–Perot (F-P) pressure sensors usually involve complex microfabrication and high-cost demodulation systems, while conventional diaphragm capsule sensors are limited in sensitivity and resolution. This work presents a low-cost, high-resolution fiber-optic F-P absolute pressure sensor. The sensor uses a vacuum capsule as one reflective surface and a partially reflective fiber collimator as the other, forming a low-finesse F-P interferometer. The cavity length is linearly modulated by the elastic deformation of the capsule under pressure, and high-precision demodulation is realized using frequency modulated continuous wave (FMCW) interferometry instead of conventional spectral methods. Static experiments from 10 to 110 kPa show that the sensor exhibits a high sensitivity of 15,105 nm/kPa and a resolution of 3.3 Pa. Furthermore, the sensor operates normally within the range of −20 °C to 70 °C, exhibiting a pressure–temperature cross-sensitivity of 0.081 kPa/°C and a cavity length drift of 496 nm/h. With the advantages of high performance, simple structure, low cost, and good scalability by selecting different capsules, the proposed sensor has promising potential for practical applications in pressure measurement fields.

Semiconductor quantum dots (QDs) are attractive materials for light-emitting devices, and the photoluminescence (PL) from QDs can be enhanced near a metal surface due to surface plasmon (SP) resonance. To integrate QDs into metal structures, QD/poly(methyl methacrylate) (PMMA) composite thin films are generally used. However, it has been reported that QDs tend to aggregate in the PMMA matrix. In this study, we fabricated two types of QD/polymer composite thin films with different degrees of QD aggregation by additionally using poly(methyl methacrylate-co-methacrylic acid) (PMMA-co-MA), which is known to prevent QD aggregation. Furthermore, these two types of films were fabricated on Ag films, with the distance between the Ag films and the QDs controlled by Al2O3 spacer layers, and the PL enhancement was compared between the two film types. Finally, we reveal that QD aggregation in the polymer matrix significantly affects the PL enhancement. Although the aggregation trends differed between PMMA and PMMA-co-MA, the results suggest a possible increase in the internal quantum efficiency (IQE) in both film types.