- Research Article
- 10.1016/j.jpowsour.2026.239580
Controllable fabrication of carbon-based multidimensional nanostructures via nickel nitrate-induced assembly for zinc-air battery
- Apr 01, 2026
- Journal of Power Sources
- Xiaowei Guo + 4 more +4
Publications from 2021 to 2026
Showing 10 of 307 papers
Controllable fabrication of carbon-based multidimensional nanostructures via nickel nitrate-induced assembly for zinc-air battery
The trojan horse in agricultural water: How microbe-mediated interactions of nanoplastics and flame retardants drive multiscale toxicity and seed transmission in rye.
Edge-centric community hiding based on permanence in attributed networks
In Situ Formation of Guanidinium Derivative and 2D/3D Heterostructure for 26.49% Efficient and Stable Inverted Perovskite Solar Cells.
Inverted perovskite solar cells (IPSCs) face challenges in achieving both high efficiency and stability due to defects that induce non-radiative recombination. Here, we introduce 1H-1,2,4-triazole-1-ammonium chloride (HTA) as a multifunctional additive that reacts with formamidinium iodide (FAI) to generate a multi-amino guanidinium derivative. This in situ formed compound enables dual passivation by coordinating with Pb2+ ions and forming hydrogen bonds with I- ions, while simultaneously templating a 2D/3D heterostructure. HTA effectively regulates nucleation kinetics, reduces defect density, and optimizes energy-level alignment. Consequently, the HTA-treated device achieves a champion power conversion efficiency (PCE) of 26.49% (certified 26.20%) with significantly enhanced stability. The unencapsulated device retains 89.15% of its initial efficiency after 2000h in ambient air, and the encapsulated device maintains 95% of its initial PCE after 1000h of maximum power point tracking. This strategy provides a promising route for developing high-performance and stable IPSCs.
Read moreHierarchical Cooperative Control of Trajectory Tracking and Stability for Distributed Drive Electric Vehicles Under Extreme Conditions
To enhance the trajectory tracking accuracy and lateral stability of distributed-drive electric vehicles, a hierarchical cooperative control strategy optimized by the Genetic–Firefly Algorithm (G-FA) is proposed. First, bottom-level controllers for trajectory tracking utilizing a Linear Quadratic Regulator (LQR) and stability relying on Sliding Mode Control (SMC) are jointly optimized offline using the G-FA to address the limitations of empirical parameter tuning and effectively mitigate chattering. Compared to traditional Nonlinear Model Predictive Control (NMPC), which relies on computationally demanding dynamic programming, the proposed G-FA acts as an efficient approximate optimization method that significantly reduces the online computational burden while maintaining high control accuracy. Second, an adaptive cooperative mechanism based on desired yaw rate correction is introduced. By constructing two reference benchmarks—“tracking-oriented” and “stability-oriented”—a cooperative weighting coefficient adapts the fusion of control objectives based on the vehicle’s stability state. Hardware-in-the-loop (HIL) simulation results demonstrate that, under high-adhesion double lane change maneuvers, the proposed strategy reduces peak lateral error and sideslip angle by 31.53% and 28.08%, respectively, compared to traditional LQR. In low-adhesion S-curve limit maneuvers, where traditional LQR fails, the proposed strategy outperforms the NMPC benchmark, further reducing these indices by 61.98% and 8.33%, respectively, significantly improving control performance under extreme conditions.
Read morePulsed Electrodeposition for Preparing Nickel, Silver/Graphene Double-Layer Composite Coatings and Study on Friction Properties
Nickel, silver/graphene double-layer composite coatings were prepared by pulsed electrodeposition. The composition, structure, mechanics and tribological properties of the coatings were investigated. Research shows that the Ag grains in the composite coatings decreased with the increase of graphene content. When the amount of graphene added to the bath reached 0.8 g/L, a large number of cracks were generated in the composite coating. When the amount of graphene added to the bath is 0.4 g/L, the microhardness of the composite coating is about 144 HV, much higher than that of the Ag coating (about 89 HV). Compared with Ag coating, the addition of graphene reduces the friction coefficient and wear rate of the coating. There are a lot of furrows on the Ag coating surface, and after the addition of graphene, the multilayer graphene makes the surface of the abrasion smooth, effectively reducing the friction coefficient of the coating, and the friction coefficient is more stable during the friction process.
Read moreSignal quantization model for controlling power electronic circuits in digital signal processing
This article discusses some key points of digital signal processing as it pertains to power electronics' digital control circuits.In this paper, we will go over some common issues with signal sampling, coherent sampling, sampling rate, jitter of the sampling pulse, successive vs. simultaneous collecting in a multichannel structure, resolution of the signal, interpolation while decimation, and digitization of analog circuits.But since they don't account for dynamic shifts and don't decrease interference, current signal estimate techniques can't provide reliable parameter data.In order to achieve high-precision signal parameter identification along with offering data for programs like wide-frequency fluctuation evaluation and enhancing energy efficiency issues, this work proposes a broadband indicate analysis approach that considers essential wave dynamics and reduces interference.To begin, knowledge about the waveforms and frequencies of the different components is extracted using the variational modal decomposition.Second, adjust the midrange frequencies so that they function as filters.Lastly, parameter estimation of wideband signals is accomplished using the least square approach.Noise, frequency dynamics modulation, frequency ramp changes, and other conditions are used to test the efficiency of the algorithm.The suggested approach successfully estimates the broadband signal's parameters with total vector errors of less than 3%, according to the results of the simulation.An improved method for determining the output signal-to-noise ratio in digital control circuits with three stages is detailed in this work.By taking these error sources into account and fixing them, we can reduce distortion and increase the signal-to-noise ratio, which improves the parameters of the output/input current and voltage and, in turn, the quality of the energy analyzing in power electronic devices.
Read morePhase portrait, bifurcation and sensitivity analysis, chaotic pattern, variational principle, Hamiltonian and new diverse wave solutions of the fractional Klein–Gordon–Zakharov system in plasma physics
Considering surface roughness O-ring lubricating-oil static seal leakage prediction via optimized circular plate gap model
Introduction O-ring seals are critical to ensuring the reliability of mechanical systems under harsh operating conditions. However, the classical parallel plate leakage model often neglects the effects of surface roughness and radial pressure distribution, leading to insufficient prediction accuracy. This study addresses this limitation by extending the classical parallel plate leakage theory to develop an optimized circular plate gap leakage model for O-rings. Methods A leakage rate correction factor μ 1 is introduced to quantify the effect of surface roughness, establishing an equivalent relationship between the micro-scale rough interface and the ideal smooth surface. The leakage rates of rough surfaces with different roughness levels under various differential pressures are theoretically calculated. Experimental validation is carried out under differential pressures of 0.3 MPa and 0.6 MPa, as well as surface roughness Ra values of 0.8 μm, 1.6 μm, and 3.2 μm. Results At a differential pressure of 0.4 MPa, the leakage rate reaches 0.67 × 10 −12 m 3 /s when Ra = 3.2μm , which is 1.8 times that of the case with Ra = 0.8μm. Experimental results show that: (1) At the same surface roughness, the cumulative leakage volume increases with the increase of differential pressure; when Ra = 1.6μm, the cumulative leakage volume at 0.6 MPa is approximately 1.5 times that at 0.3 MPa. (2) At the same differential pressure, a larger Ra results in a higher cumulative leakage volume; at 0.3 MPa, the cumulative leakage volume at Ra = 3.2μm is about 1.7 times that at Ra = 0.8μm. Overall, the leakage rate increases almost linearly with the increase of both differential pressure and surface roughness. The relative error between theoretical and experimental values is within 15%. Discussion The relative error within 15% confirms the reliability of the proposed model. However, uncertainties in the model primarily stem from unaccounted factors, including high temperature, long-term O-ring aging, extreme high pressure, and idealized model assumptions. Consequently, the model is only valid under conditions of room temperature, low pressure, and short-term service. Nevertheless, this work provides a robust analytical framework for O-ring leakage prediction and sealing performance optimization in engineering applications.
Read morePre-harvest sprouting impairs dough functionality primarily via reduction in gluten quantity