6T SRAM cell design and analysis in 45 nm technology node

-As the demand for low-power, high-performance memory systems grows, the design of efficient SRAM (Static Random Access Memory) cells becomes increasingly crucial. This paper explores the power consumption, performance, and stability of two SRAM cell designs: the conventional 6T and the Single Ended 6T SRAM. While the conventional 6T SRAM is prone to read disturb noise and high leakage power, it remains widely used due to its simplicity and compactness. To address these issues, the Single Ended 6T SRAM cell is introduced as an alternative, which reduces both power consumption and area while maintaining competitive performance. The study provides a detailed analysis of static and dynamic power consumption, read/write stability, and overall energy efficiency for both cell architectures. Simulation results show that the Single Ended 6T SRAM offers significant improvements in power reduction without compromising speed, making it a promising solution for future low-power, high-performance memory applications. Keywords— SRAM cell, Pre-Charge Circuits, Sense Amplifiers, and Single-Ended vs. Conventional 6T SRAM Cell.

Variability-aware 7T SRAM circuit with low leakage high data stability SLEEP mode

This research paper proposes a low-power, high-stability 8T static random access memory (SRAM) cell. The proposed SRAM cell is a modified structure of the conventional 6T SRAM cell. The introduction of two diode-connected transistors in the pull-down network of the conventional 6T SRAM cell gives the proposed 8T SRAM cell structure. The presence of diode-connected transistors improves the power and noise performances of the proposed cell as compared to those of the conventional bit cells. The power consumption and static noise margin (SNM) of the suggested SRAM cell are calculated for write, hold and read operations. Also, the write and read delays of the proposed and conventional bit cells are observed. The power, speed, noise margin and area of the proposed 8T SRAM cell are compared with those of some of the existing SRAM cells. In comparison to conventional SRAM cells, the proposed cell consumes less power and has higher stability, according to the study. A novel dual-supply ([Formula: see text][Formula: see text]V and [Formula: see text][Formula: see text]V or 200[Formula: see text]mV) concept is applied for the existing and proposed SRAM cells. The noise and power performances of SRAM cells are well improved under the condition of dual supply as compared to the conventional supply voltage ([Formula: see text][Formula: see text]V and [Formula: see text][Formula: see text]V). A [Formula: see text] memory array of the proposed 8T SRAM cell is formed and the performance of the array structure is compared with that of [Formula: see text] array of the conventional 6T SRAM cell. The layouts of existing and proposed SRAM cells are illustrated. The simulation is carried out using the Cadence Virtuoso simulation EDA tool in 90-nm CMOS technology.

A low power CMOS Static Random Access Memory (SRAM) based Field Programmable Gate Arrays (FPGA) architecture is being presented in this paper. The architecture presented here is based on CMOS logic and CMOS SRAMs that are used for on-chip dynamic reconfiguration. This architecture employs the fast and low-power SRAM blocks that are based on 10T SRAM cells. These blocks are employed in fast access of the configuration bits by using the shadow SRAM technique. The dynamic reconfiguration delay is being hidden behind the computation delay through the use of shadow SRAM cells. The combined effect of both the SRAM memory cells and the shadow SRAM scheme enables to support in reducing the delay and also to achieve reduced power consumption. Experimental results show reduced delay of about 8.035ns and power consumption of about 0.015W for the 10T SRAM memory cell with an overhead in area, relative to 4T and 6T SRAM cells. Also, the experimental results include the values of delay of about 8.979ns and power consumption of about 0.052W, achieved for the LB of FPGA architecture which employs CMOS SRAMs using the 10T SRAM memory cells in it.

This article presents a comprehensive assessment on the 6T static random access memory (SRAM) cell with 7-nm FinFET technology by implementing quantum physics-based device-circuit cooptimization. Seven key device design parameters and their multiple impacts on a 6T SRAM cell are systematically evaluated, focusing on materials band engineering, device design, circuit parameters tradeoff, and variation control. The area of SRAM cell under the same Fin quantization scheme remains constant in all evaluations. To the best of our knowledge, the most comprehensive discussion about circuit optimization from multiple device design parameters perspective is presented. Based on our cooptimization scheme, a SRAM cell is effectively designed. For a low-power and robust SRAM cell design, we achieve 56.7% reduction in leakage, 7.9% improvement in hold noise margin (HNM), 8.6% improvement in read noise margin (RNM), and 10.8% improvement in write margin (WM) at the expense of 19.3% increase in delay under design space of gate length (Lg) and spacer thickness (TSPC). For a high-speed SRAM cell design, we recommend focusing on the optimization of architecture and peripheral circuits. This framework not only has the advantages of easy implementation, technology-friendly, and high accuracy, but also suitable for path-finding researches on 5-nm node and beyond.

We present a hybrid nanoelectromechanical (NEM)/CMOS static random access memory (SRAM) cell, in which the two pull-down transistors of a conventional CMOS six transistor (6T) SRAM cell are replaced with NEM relays. This SRAM cell utilizes the infinite subthreshold slope and hysteretic properties of NEM relays to dramatically increase the cell stability compared to the conventional CMOS 6T SRAM cells. It also utilizes the zero off-state leakage of NEM relays to significantly decrease static power dissipation. The structure is designed so that the relatively long mechanical delay of the NEM relays does not result in performance degradation. Circuit simulations are performed using a VerilogA model of a NEM relay. Compared to a 65nm CMOS 6T SRAM cell, when 10nm-gap NEM relays (pull-in voltage = 0.8V, pull-out voltage = 0.2V, on resistance = 1ki2) are integrated, hold and read static noise margin (SNM) improve by ~110% and ~250%, respectively. In addition, static power dissipation decreases by ~85%. The write delay decreases by ~60%, while read delay decreases by ~10%. The advantages in SNM and static power dissipation are expected to increase with scaling.

Over the last five decades, researchers have been downsizing complementary metal–oxide–semiconductor (CMOS) electronics to accomplish effective execution regarding speed, power blow-out, size, and unwavering quality. Our motive is to make the general electronics that use gadgets such as PCs progressively smaller size, better speed, and mini power utilization. The scaling of CMOS is done to accomplish pace and decrease memory size. Static Random Access Memory (SRAM) is used to store information in convenient gadgets. Presently, 6T (6 transistor) SRAM is more favored than 8T and 9T in light of the fact that 6T SRAM cell gives a very low delay when contrasted with 8T and 9T SRAM and, furthermore, the power dissipation is half of what is dissipated in 8T and 9T SRAM. This paper acquiesces the design and realization of 6T SRAM bit cell in 180 nm, 90 nm, and 45 nm CMOS technology on cadence virtuoso EDA tool. The performance characteristics of 6Transistor Static RAM has been evaluated with reference to power and delay.

Low power and noise tolerant static random access memory (SRAM) cells are in high demand today. This paper presents a stable differential SRAM cell that consumes low power. The proposed cell has similar structure to conventional 6T SRAM cell with the addition of two buffer transistors, one tail transistor and one complementary word line. Due to stacking effect, the proposed cell achieves lower power dissipation. In this paper, impact of process parameters variations on various design metrics of the proposed cell are presented and compared with conventional differential 6T (D6T), transmission gate-based 8T (TG8T), and single ended 8T (SE8T) SRAM cells. Impact of process variation, like threshold voltage and length, on different design metrics of an SRAM cell like, read static noise margin (RSNM), read access time ( ${T_{\mathrm{RA}}}$ ), and write access time ( ${T_{\mathrm{ WA}}} $ ) are also presented. The proposed cell achieves ${1.12{\times } /{\mathrm{ 1}}.{\mathrm{ 43}}{\times } /{\mathrm{ 5}}.{\mathrm{ 62}}\times } $ improvement in ${T_{\mathrm {RA}}}$ compared to TG8T/D6T/SE8T at a penalty of $ {1.1{\times } /{4}.{88}\times }$ in $ {T_{\mathrm{ WA}}} $ compared to D6T/TG8T and $ {1.19{\times } /1.18\times } $ in read/write power consumption compared to D6T. An improvement of $ {\rm 1.{\mathrm{ 12}}{\times } /{\mathrm{ 2}}.{\mathrm{ 15}}\times } $ in RSNM is observed compared to D6T/TG8T. The proposed cell consumes $ {5.38\times } $ less power during hold mode and also shows ${2.33\times } $ narrower spread in hold power @ $ {V_{\mathrm{ DD}} = 0.{\mathrm{ 4}}}$ V compared to D6T SRAM cell.

The growing demand for low-power static random access memory (SRAM) cells in Internet of Things (IoT) devices has led to the development of various SRAM cell topologies that minimize power consumption while maintaining performance and stability. In this paper, we have analyzed various SRAM designs based on different parameters, such as power dissipation, delay, area, energy, and stability. It is observed that 6T SRAM cell, consisting of six transistors, is the most widely used topology due to its simplicity and low area requirements. However, larger cells such as 8T,9T, and 10T have been developed to improve stability and reduce power consumption, although they require more area. It has been observed8 T work better for read delay while 9T works better for 9 Scaling down SRAM cells to smaller feature sizes presents challenges in maintaining stability and reliability while minimizing power consumption.

As CMOS devices near the nanometer regime, scaling them down has a number of repercussions, such as short channel effects and process fluctuations, which degrade the device's reliability and performance. FinFET is one of the promising ones for overcoming this problem, according to researchers, because it has better channel management and lower overall capacitance, the 6T Static Random Access Memory (SRAM) circuit design will perform better. This research study evaluates 6T and 9T SRAM cells created with CMOS and FinFET by utilizing 22nm technology and further these SRAM cells are compared based on numerous performance characteristics such as write delay, read delay, static power and static noise margin (SNM). The Predictive Technology Models (PTM) files are used to simulate the 22nm CMOS and FinFET based SRAM cells which are developed by Arizona State University in the Cadence Virtuoso tool.

Design of high stability, low power and high speed 12 T SRAM cell in 32-nm CNTFET technology

SummaryThis work presents a robust and low leakage new 8T static random access memory (SRAM) cell without any half‐selection disturbance. The proposed cell removes write disturbance by eliminating the trail from supply and ground. Furthermore, it removes the read disturbance by separating the read trail from the storage node. The proposed cell addresses the challenge of half select by using different control signals. The cell achieves low leakage because of virtual ground (VGND), series connected tail transistor, and access series stack transistors. To study the usefulness of the proposed SRAM, it is compared with 6T, 10T, 9T, PG9T, 7T, and 8T SRAM cells. The proposed SRAM minimizes leakage power, write power, and read power by 12.4%, 21.62%, and 29.06%. Furthermore, the proposed cell improves read and write noise margin by 57.19% and 19.96%, respectively, as compared to a conventional 6T SRAM. Again, the write energy consumption lowers to about 43.86× while read energy consumption 28.95× as compared to 10T SRAM.

In modern technology era, the demand for Static Random Access Memory (SRAM) cells has been greatly increased due to its wide variety of applications. Power consumption, speed, read stability and leakage issues are the major design challenges related to SRAM. This paper presents a novel SRAM cell based on Multiple Supply Voltages and non-precharged RBL (MS-N10T) and also shows the comparison of various SRAM cells based on lector, sleep transistors and Transmission gate (TG) to reduce the power consumption when compared to LP10T. The SRAM cell MS-N10T when used in combination of TG and sleep transistors (TGNS-13T) further reduces the power consumption. The analysis further shows that the SRAM, TGNS13T reduces the power consumption approximately by 70-80%. On the Other hand, the LC14T SRAM cell enhances the stability approximately by 80-85%. The major objective of this work is to reduce the power consumption with marginal increase in propagation delay and to improve read stability so as to meet the challenges of advancements in technologies. All the various SRAM architectures are implemented using Cadence 45nm CMOS technology.  Â

In this paper, we propose a new design of high‐performance ultralow power carbon nanotube field effect transistor (CNTFET)‐based nine‐transistor static random access memory (SRAM) cell and its implementation using shared bitline (BL) and half‐select free techniques. Simulations of the 9T SRAM design, using CNTFET compact model, have presented merits over the silicon‐complementary‐metal oxide semiconductor (CMOS) SRAM cell in terms of leakage current, power consumption, and stability. Uses of the half‐select free technique eliminate the conflict between read and write operations and shared BL technique offers reduced physical layout area and enhanced data access speed. Further, uses of the increased number of tubes or say CNT array in the CNTFET device increases the probability of functionality (>95%) with a high yield SRAM cell.

Low-power integrated circuits are in high demand due of the wide variety of electronic portable devices for which they are used. SoC (System on Chips) power consumption and speed are both determined by on-chip SRAM (Static Random Access Memory) performance. We have been making CMOS devices smaller for almost 50 years to make them more portable and small and to improve their performance in terms of access time, power use, latency, and other factors. Low supply voltage and leakage energy have been the primary focus due to the potential for dramatically lower power usage. Along with the leakage power, power consumption and speed are the main considerations for chip design. This article covers the simulation of 6T, 7T, and 8T SRAM cells utilizing low power reduction approaches and builds a modified model that offers the user with a product that costs less and has decreased power delay. SRAM cells in various configurations (6T, 7T, and 8T) have been constructed and compared using read delay, write delay, and leakage reduction strategies as the foundation for our research here.