A GRID approach for gravitational waves signal analysis with a multi-standard farm prototype

We propose a multistep procedure for the on-line detection and analysis of gravitational wave signals emitted during the coalescence of compact binaries. This procedure, based on a hierarchical strategy, consists of a rough analysis of the gravitational wave signal using adaptive line enhancers (ALE) filters and the controlled random search (CRS) optimization algorithm followed by a refined analysis using the classic matched-filtering technique. The results of simulations for the rough analysis are quite promising both for the relatively small computational power needed and for the robustness of the algorithms used, so that it could be very helpful for gravitational wave detection with very large baseline interferometric detectors like LIGO and VIRGO.

Today's communication architectures for parallel machines reduce communication overheads and latencies by over an order of magnitude. However, carrying over these techniques to workstation clusters connected by an ATM network presents major design challenges. We discuss the differences in communication characteristics between workstation clusters built from standard hardware and software components and state-of-the-art multiprocessors, and then evaluate a prototype implementation of an active message communication layer. Application round-trip latencies of about 50 microseconds for small messages roughly compare to a similar implementation on the Thinking Machines CM-5 multiprocessor.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>

&lt;div class="htmlview paragraph"&gt;The carbon dioxide removal assembly (CDRA) is an essential part of the International Space Station (ISS) environmental control and life support system. As such, this system is required to selectively remove carbon dioxide from the cabin atmosphere, and discharge it overboard to space vacuum. Verification of the many CDRA requirements is divided into analysis, demonstration, inspection, and test methods. This paper focuses on the results of protoflight performance testing conducted on the first deliverable CDRA. The results of this performance testing indicated that the CDRA design exceeded all of the performance requirements.&lt;/div&gt;

Implementing and debugging high-performance network subsystems is a challenging task. In this paper, we present our experiences from developing and debugging a network interface card (NIC). Our NIC targets networked storage subsystems (Marazakis et al., 2006). For this purpose it mainly provides support for remote direct-memory-access (RDMA) write, sender-side notification of RDMA write completion, and receiver-side interrupt generation. In our work we examine issues that arise during system implementation and debugging, both in terms of correctness as well as performance. We present an analysis of the individual problems we encounter and we discuss how we address each case. For most problems we encounter, it is not possible to rely on existing debugging tools. However, we find that most of the techniques we use in this process, rely on collecting some form of event records from software or hardware components. We believe that such capabilities can be provided for independent hardware or software components in isolation, a fairly straight-forward task, thus, significantly simplifying the debugging process in complex systems of this nature

The economics of semiconductor manufacturing have forced process engineers to develop techniques to increase wafer yield. Improvements in process controls and uniformities in all areas of the fab have reduced film thickness variations at the very edge of the wafer surface. This improved uniformity has provided the opportunity to consider decreasing edge exclusions, and now the outermost extents of the wafer must be considered in the yield model and expectations. These changes have increased the requirements on lithography to improve wafer edge printability in areas that previously were not even coated. This has taxed all software and hardware components used in defining the optical focal plane at the wafer edge. We have explored techniques to determine the capabilities of extreme wafer edge printability and the components of the systems that influence this printability. We will present current capabilities and new detection techniques and the influence that the individual hardware and software components have on edge printability. We will show effects of focus sensor designs, wafer layout, utilization of dummy edge fields, the use of non-zero overlay targets and chemical/optical edge bead optimization.

MOPS is a platform for surgical robotics research. It consists of hardware and software components for building surgical robot systems based on existing robot arms. The reference system presented in this paper has two robot arms, each with an adapter for mounting and actuating different types of surgical instruments. Additionally, the system has a high-resolution stereo camera and a simple operator console with haptic devices and foot pedals for teleoperating the manipulators. Software components are based on Robot Operating System (ROS) to keep them modular and reusable for different types of hardware. We evaluate the precision of our system for vision-based tasks and demonstrate its potential for surgical task automation. The mean end-to-end error, including that of the vision system, for a trajectory following task was 1.2mm / 0.3° for one manipulator and 2.7mm / 0.7° for the other. MOPS software and hardware components are made available under an open-source license to encourage collaboration and facilitate the advancement of surgical robotics research.

Digital photography has many advantages over the conventional method. At present commercially available digital ophthalmological imaging systems utilise only a fraction of the advantages of this technique and some of them have fundamental conceptional problems. Images of a fundus camera, a slit lamp and a scanning laser ophthalmoscope were digitised using digital and video cameras and/or frame grabber cards. Digital images and movies were recorded via a personal computer. The image recording software was developed using an imaging library and open source software. The recorded images and video sequences were processed with three different commercially available programme packages. The images were archived in a around-the-clock accessible database. Our digital imaging system is capable to record normal and high resolution slit lamp images, colour fundus images in normal resolution, Fluorescein angiography images in normal and high resolution, digital simultaneous ICG and Fluorescein videoangiograms (without compression) and high resolution macro images. Different functions, e.g., contrast enhancement are integrated in the image capture software. Most of the parameters of the image acquisition are individually adaptable. The digital image archive supports multiple image and video formats. Using standard software and hardware components an imaging system can be constructed featuring functions usually not available in commercial ones. Since the system is adaptable, recording of images with a wide variety of parameters, e.g., for measurements for scientific experiments, is possible.

In 2014, Cikarang Listrindo Energy built a steam power plant in Babelan to participate in the government programs. In April 2017, Unit 1 of PLTU Babelan has been operated. After the plant has been in operation for 4 months, the plant will have a performance test for the main part of the steam power plant, one of which is the steam turbine performance test. This performance test purpose is to get actual performance data where it will be compared to the design data, and it willl be used for warranty from the steam turbine contractor. The performance test is using ASME PTC 6 for steam turbine performance test. The steam turbine performance test can be seen from several parameters such as test capability, heat rate and turbine efficiency. The results of the steam turbine performance test based on the design are: the output power is 138,010 MW; the heat rate is 8865 kJ/kWh; and the turbine efficiency is 87.38%. Meanwhile the results of the performance test based on commissioning are: the output power is 139,295 M; the heat rate is 8919 kJ/kWh; and the turbine efficiency is 87.03%. The actual performance test results are: the output power is 137,595 MW, the heat rate is 8830.64 kJ/kWh, and the turbine efficiency is 88.65%. The tolerance given from ASME PTC 6 is 2%. Exhaust turbine pressure affect the turbine efficiency, where as lower exhaust turbine pressure causes higher turbine efficiency.

Commodity DRAM-based processing-using-memory (PuM) techniques that are supported by off-the-shelf DRAM chips present an opportunity for alleviating the data movement bottleneck at low cost. However, system integration of these techniques imposes non-trivial challenges that are yet to be solve d . Potential solutions to the integration challenges require appropriate tools to develop any necessary hardware and software components. Unfortunately, current proprietary computing systems, specialized DRAM-testing platforms, or system simulators do not provide the flexibility and/or the holistic system view that is necessary to properly evaluate and deal with the integration challenges of commodity DRAM-based PuM techniques. We design and develop Processing-in-DRAM (PiDRAM), the first flexible end-to-end framework that enables system integration studies and evaluation of real, commodity DRAM-based PuM techniques. PiDRAM provides software and hardware components to rapidly integrate PuM techniques across the whole system software and hardware stack. We implement PiDRAM on an FPGA-based RISC-V system. To demonstrate the flexibility and ease of use of PiDRAM, we implement and evaluate two state-of-the-art commodity DRAM-based PuM techniques: (i) in-DRAM copy and initialization (RowClone) and (ii) in-DRAM true random number generation (D-RaNGe) . We describe how we solve key integration challenges to make such techniques work and be effective on a real-system prototype, including memory allocation, alignment, and coherence. We observe that end-to-end RowClone speeds up bulk copy and initialization operations by 14.6× and 12.6×, respectively, over conventional CPU copy, even when coherence is supported with inefficient cache flush operations. Over PiDRAM’s extensible codebase, integrating both RowClone and D-RaNGe end-to-end on a real RISC-V system prototype takes only 388 lines of Verilog code and 643 lines of C++ code.

IDAMS is a prototype of a general purpose system for interactive data manipulation. The paper analyzes the requirements for an interactive pictorial data base system and shows that the known requirements for pictorial application can best be met by a general purpose system such as IDAMS. Major features of IDAMS are: the powerful high level data manipulation language. the datatypes of APL plus extensions for interactive data analysis. the convenient extensibility of the system by functions written in FORTRAN, PL/I or ASSEMBLY language. the interactive extensibility via APL, both within and in addition to the data manipulation language. the convenient access to special purpose hardware including image processing devices. The ease, with which the general purpose system can be adapted to a pictorial application, is contrasted with the problems and risks introduced by the development of a special purpose data base system for pictorial applications.KeywordsHigh Level LanguageAssembly LanguageCentral InterfaceData Base SystemIntegrate Data AnalysisThese keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

The public transport system of New South Wales (NSW), Australia is impotent to receive 100% of the fare from light rail and buses due to the unavailability of a continuous real-time monitoring system. This scheme thereby seeks to help update the NSW public transport ticket collection system, with the aid of a counter that will be integrated into the public transportation within the Ticket Tapping Machine, to provide passenger count against the number of touches occurring at each stop; and thus, increasing the revenue. The product comprises of hardware and software components - the hardware system is located within the public transport while the software system incorporating a web portal is positioned for the authorities to have access to the real-time passenger data. At the hardware end, the ultrasonic sensors and the raspberry pi would detect the number of passengers on the transport and the LCD screen would display the number of passengers who had not tapped their smart card ticket. Additionally, the raspberry pi module used in the hardware component can denote the transportation location with the help of an in-built Wi-Fi component. With this designed technology, the authorities would be able to monitor and record the movements of the passenger in real-time system addressing the existing challenges faced by the NSW public transport authority, especially in the case of light rail and buses being used for free by certain passengers.

Wellbore integrity is a critical subject in oil and gas production, and CO2 storage. Successful subsurface deposition of various fluids, such as CO2, depends on the integrity of the storage site. In a storage site, injection wells and pre-existing wells might leak due to over-pressurization, mechanical/chemical degradation, and/or a poor cement job, thus reducing the sealing capacity of the site. Wells that leak due to microannuli or cement fractures on the order of microns are difficult to seal with typical workover techniques. We tested a novel polymer gelant, originally developed for near borehole isolation, in a pilot experiment at Mont Terri, Switzerland to evaluate its performance in the aforementioned scenario. The polymer gel sealant was injected to seal a leaky wellbore drilled in the Opalinus Clay as a pilot test. The success of the pH-triggered polymer gel (sealant) in sealing cement fractures was previously demonstrated in laboratory coreflood experiments (Ho et al. 2016, Tavassoli et al. 2018). pH-sensitive microgels viscosify upon neutralization in contact with alkaline cement to become highly swollen gels with substantial yield stress that can block fluid flow. The leaky wellbore setup was prepared by heating-cooling cycles to induce leakage pathways in the cased and cemented wellbore. The leakage pathways are a combination of fractures in the cement and microannuli at the cement-formation interface. The exact nature of these leakage pathways can be determined by over-coring at the end of the experiment life. We used polyacrylic acid polymer (sealant) to seal these intervals. The process comprises of three stages: (1) injection of a chelating agent as the preflush to ensure a favorable environment for the polymer gel, (2) injection of polymer solution, and (3) shut-in for the polymer gelation. Then, we evaluated the short-/long-term performance of the sealant in withholding the injected fluids (formation brine and CO2 gas). The novel sealant was successfully deployed to seal the small aperture pathways of the borehole at the pilot test. We conducted performance tests using formation brine and CO2 gas to put differential pressure on the polymer gel seal. Pressure and flow rate at the specific interval were monitored during and after injection of brine and CO2. Results of performance tests after polymer injection were compared against those in the absence of the sealant. Several short-term (4 min) constant-pressure tests at different pressure levels were performed using formation brine, and no significant injection flow rate (rates were below 0.3 ml/min) was observed. The result shows more than a ten-fold drop in the injection rate compared to the case without the sealant. The polymer gel showed compressible behavior at the beginning of the short-term performance tests. Our long-term (1-week) test shows even less injectivity (~0.15 ml/min) after polymer gelation. The CO2 performance test shows only 3 bar pressure dissipation overnight after injection compared to abrupt loss of CO2 pressure in the absence of polymer gel. Sealant shows good performance even in the presence of CO2 gas with high diffusivity and acidity. Pilot test of our novel sealant proves its competency to mitigate wellbore leakage through fractured cement or debonded microannuli, where other remedy techniques are seldom effective. The effectiveness of the sealing process was successfully tested in the high-alkaline wellbore environment of formation brine in contact with cement. The results to date are encouraging and will be further analyzed once over-coring of the wellbore containing the cemented annulus occurs. The results are useful to understand the complexities of cement/wellbore interface and adjust the sealant/process to sustain the dynamic geochemical environment of the wellbore.

Developing a component-bassed software requires verified and standardized software components. This paper presents and approach to build conponent quality assurance process based on process patterns. To describe process patterns, a metamodel is suggested and several process for software components. The process pattern approach was applied to real projects and its advantages and disadvantages are discussed.

As the development of technology, the mobile phone world also has developed very quickly. Mobile communication and services, over emerging wireless technologies, provide anyone, anytime and anywhere access. Moreover, the intelligence is now often embedded into modern applications, such as surveillance and supervising systems. This work presents an intelligent and a pervasive supervising platform for information system (IS) security based on multi-agent systems (MAS) which detects and classifies malware events that occurs on software and hardware components and sends real time notification to smart phone users. The proposed platform is formed by two components: The first one consists of a Central Software Component (CSC); the supervisor application that manages devices and evaluates logs and alarms of the supervised components. The second one consists of an Embedded Software Component (ESC) on the Mobile Device (MD) with an ANDROID OS. In our platform, we have implemented agents on ESC using JADE-LEAP android, note that the ESC is targeted to smart phones and tablet that run the operating system Android, JADE API on CSC and the communication between these two components is performed using the Secure Socket Layer (SSL) protocol implemented using the JADE-S plug-in.

Advances in sensor technology have rapidly increased our ability to monitor natural and human-made physical systems. In many cases, it is critical to process the resulting large volumes of data on a regular schedule and alert system operators when the system has changed. Automated quality control and performance monitoring can allow system operators to quickly detect performance issues. Pecos is an open source python package designed to address this need. Pecos includes built-in functionality to monitor performance of time series data. The software can be used to automatically run a series of quality control tests and generate customized reports which include performance metrics, test results, and graphics. The software was developed specifically for solar photovoltaic system monitoring, and is intended to be used by industry and the research community. The software can easily be customized for other applications. The following Pecos documentation includes installation instructions and examples, description of software features, and software license. It is assumed that the reader is familiar with the Python Programming Language. References are included for additional background on software components.