A Non-Human Primate Brain-Computer Typing Interface.

Objective. Brain–computer interface (BCI) technologies have been intensely studied to provide alternative communication tools entirely independent of neuromuscular activities. Current BCI technologies use electroencephalogram (EEG) acquisition methods that require unpleasant gel injections, impractical preparations and clean-up procedures. The next generation of BCI technologies requires practical, user-friendly, nonintrusive EEG platforms in order to facilitate the application of laboratory work in real-world settings. Approach. A capacitive electrode that does not require an electrolytic gel or direct electrode–scalp contact is a potential alternative to the conventional wet electrode in future BCI systems. We have proposed a new capacitive EEG electrode that contains a conductive polymer-sensing surface, which enhances electrode performance. This paper presents results from five subjects who exhibited visual or auditory steady-state responses according to BCI using these new capacitive electrodes. The steady-state visual evoked potential (SSVEP) spelling system and the auditory steady-state response (ASSR) binary decision system were employed. Main results. Offline tests demonstrated BCI performance high enough to be used in a BCI system (accuracy: 95.2%, ITR: 19.91 bpm for SSVEP BCI (6 s), accuracy: 82.6%, ITR: 1.48 bpm for ASSR BCI (14 s)) with the analysis time being slightly longer than that when wet electrodes were employed with the same BCI system (accuracy: 91.2%, ITR: 25.79 bpm for SSVEP BCI (4 s), accuracy: 81.3%, ITR: 1.57 bpm for ASSR BCI (12 s)). Subjects performed online BCI under the SSVEP paradigm in copy spelling mode and under the ASSR paradigm in selective attention mode with a mean information transfer rate (ITR) of 17.78 ± 2.08 and 0.7 ± 0.24 bpm, respectively. Significance. The results of these experiments demonstrate the feasibility of using our capacitive EEG electrode in BCI systems. This capacitive electrode may become a flexible and non-intrusive tool fit for various applications in the next generation of BCI technologies.

To enhance the information transfer rate (ITR) of a steady-state visual evoked potential (SSVEP)-based speller, more characters with flickering symbols should be used. Increasing the number of symbols might reduce the classification accuracy. A hybrid brain-computer interface (BCI) improves the overall performance of a BCI system by taking advantage of two or more control signals. In a simultaneous hybrid BCI, various modalities work with each other simultaneously, which enhances the ITR. In our proposed speller, simultaneous combination of electromyogram (EMG) and SSVEP was applied to increase the ITR. To achieve 36 characters, only nine stimulus symbols were used. Each symbol allowed the selection of four characters based on four states of muscle activity. The SSVEP detected which symbol the subject was focusing on and the EMG determined the target character out of the four characters dedicated to that symbol. The frequency rate for character encoding was applied in the EMG modality and latency was considered in the SSVEP modality. Online experiments were carried out on 10 healthy subjects. The average ITR of this hybrid system was 96.1 bit/min with an accuracy of 91.2%. The speller speed was 20.9 char/min. Different subjects had various latency values. We used an average latency of 0.2 s across all subjects. Evaluation of each modality showed that the SSVEP classification accuracy varied for different subjects, ranging from 80% to 100%, while the EMG classification accuracy was approximately 100% for all subjects. Our proposed hybrid BCI speller showed improved system speed compared with state-of-the-art systems based on SSVEP or SSVEP-EMG, and can provide a user-friendly, practical system for speller applications.

Estimating and approaching the maximum information rate of noninvasive visual brain-computer interface

A large number of incommensurable metrics are currently used to report the performance of brain-computer interfaces (BCI) used for augmentative and alterative communication (AAC). The lack of standard metrics precludes the comparison of different BCI-based AAC systems, hindering rapid growth and development of this technology. This paper presents a review of the metrics that have been used to report performance of BCIs used for AAC from January 2005 to January 2012. We distinguish between Level 1 metrics used to report performance at the output of the BCI Control Module, which translates brain signals into logical control output, and Level 2 metrics at the Selection Enhancement Module, which translates logical control to semantic control. We recommend that: (1) the commensurate metrics Mutual Information or Information Transfer Rate (ITR) be used to report Level 1 BCI performance, as these metrics represent information throughput, which is of interest in BCIs for AAC; 2) the BCI-Utility metric be used to report Level 2 BCI performance, as it is capable of handling all current methods of improving BCI performance; (3) these metrics should be supplemented by information specific to each unique BCI configuration; and (4) studies involving Selection Enhancement Modules should report performance at both Level 1 and Level 2 in the BCI system. Following these recommendations will enable efficient comparison between both BCI Control and Selection Enhancement Modules, accelerating research and development of BCI-based AAC systems.

The possibility of an effective connection between neural tissue and computers has inspired scientists and engineers to develop new ways of controlling and obtaining information from the nervous system. These applications range from `brain hacking' to neural control of artificial limbs with brain signals. Notwithstanding the significant advances in neural prosthetics in the last few decades and the success of some stimulation devices such as cochlear prosthesis, neurotechnology remains below its potential for restoring neural function in patients with nervous system disorders. One of the reasons for this limited impact can be found at the neural interface and close attention to the integration between electrodes and tissue should improve the possibility of successful outcomes.The neural interfaces research community consists of investigators working in areas such as deep brain stimulation, functional neuromuscular/electrical stimulation, auditory prostheses, cortical prostheses, neuromodulation, microelectrode array technology, brain–computer/machine interfaces. Following the success of previous neuroprostheses and neural interfaces workshops, funding (from NIH) was obtained to establish a biennial conference in the area of neural interfaces. The first Neural Interfaces Conference took place in Cleveland, OH in 2008 and several topics from this conference have been selected for publication in this special section of the Journal of Neural Engineering. Three `perspectives' review the areas of neural regeneration (Corredor and Goldberg), cochlear implants (O'Leary et al) and neural prostheses (Anderson). Seven articles focus on various aspects of neural interfacing. One of the most popular of these areas is the field of brain–computer interfaces. Fraser et al, report on a method to generate robust control with simple signal processing algorithms of signals obtained with electrodes implanted in the brain. One problem with implanted electrode arrays, however, is that they can fail to record reliably neural signals for long periods of time. McConnell et al show that by measuring the impedance of the tissue, one can evaluate the extent of the tissue response to the presence of the electrode. Another problem with the neural interface is the mismatch of the mechanical properties between electrode and tissue. Basinger et al use finite element modeling to analyze this mismatch in retinal prostheses and guide the design of new implantable devices. Electrical stimulation has been the method of choice to activate externally the nervous system. However, Zhang et al show that a novel dual hybrid device integrating electrical and optical stimulation can provide an effective interface for simultaneous recording and stimulation. By interfacing an EMG recording system and a movement detection system, Johnson and Fuglevand develop a model capable of predicting muscle activity during movement that could be important for the development of motor prostheses. Sensory restoration is another unsolved problem in neural prostheses. By developing a novel interface between the dorsal root ganglia and electrodes arrays, Gaunt et al show that it is possible to recruit afferent fibers for sensory substitution. Finally, by interfacing directly with muscles, Jung and colleagues show that stimulation of muscles involved in locomotion following spinal cord damage in rats can provide an effective treatment modality for incomplete spinal cord injury.This series of articles clearly shows that the interface is indeed one of the keys to successful therapeutic neural devices. The next Neural Interfaces Conference will take place in Los Angeles, CA in June 2010 and one can expect to see new developments in neural engineering obtained by focusing on the neural interface.

Brain-computer interface (BCI) systems have emerged as an augmentative technology that can provide a promising solution for individuals with motor dysfunctions and for the elderly who are experiencing muscle weakness. Steady-state visually evoked potentials (SSVEPs) are widely adopted in BCI systems due to their high speed and accuracy when compared to other BCI paradigms. In this paper, we apply combined magnitude and phase features for class discrimination in a real-time SSVEP-based BCI platform. In the proposed real-time system users gain control of a motorised bed system with seven motion commands and an idle state. Experimental results amongst eight participants demonstrate that the proposed real-time BCI system can successfully discriminate between different SSVEP signals achieving high information transfer rates (ITR) of 82.73 bits/min. The attractive features of the proposed system include noninvasive recording, simple electrode configuration, excellent BCI response and minimal training requirements.

The aim of brain–computer interface (BCI) is to support the daily life of individuals with severe disabilities. For practical BCI, ease of use is one of the most important factors, which is enhanced when fewer electrodes are used. However, using fewer electrode affect the performance of BCI negatively. In this study, a novel single-channel steady-state visual evoked potential (SSVEP) detection method with subject-specific sinusoids approach (SSSA) was developed to enhance the performance of single channel SSVEP based BCI, therefore, to assist the ease of use. For the SSSA, subject-specific sinusoids were defined from training data based on SSVEP frequency and phase features. To detect the SSVEP response, defined sinusoids were used as reference. To evaluate the detection performance of the developed method, it was compared with the well-known power spectral density analysis (PSDA), least absolute shrinkage and selection operator (LASSO) and advanced canonical correlation analysis (CCA) methods on a benchmark dataset. The experimental results showed significantly greater detection accuracy and information transfer rate (ITR) with the SSSA method compared to the PSDA, LASSO and advanced CCA methods. And it is worth to noting that subject-specific sinusoids better represent SSVEP response than template signals that used in advanced CCA. Also proposed method reached one of the highest ITRs reported with max 125 and average 81 bits/min ITRs for single-channel SSVEP based BCI.

People with severe physical disabilities are not able of using standard robotic wheelchairs, which generally demand some motor skills, and therefore total usage of associate muscles. Robotic wheelchairs commanded by Brain-Computer Interfaces (BCIs) based on Electroencephalography (EEG) have demonstrated to be an alternative for these end-users. In general, existing robotic wheelchairs commanded by BCIs require special platforms adapted to the EEG-BCI, and end-users need to attend a long training process for safely drive these devices. But many times these potential users do not have access to training sessions; due to mobility problems or technology access restrictions. This study proposes an EEG-based BCI with customizable configuration to be used in cloud architectures for remote control of robotic wheelchairs. This research explores two types of Steady State Visual Evoked Potential (SSVEP)-based BCI by applying Canonical Correlation Analysis (CCA) and compressive sensing (CS) as a novelty, adopting in one free calibration, and other including a calibration stage. The free-calibrated SSVEP recognition approach (CS-ncCCA) using compression ratio (CR) at 60% obtained accuracy (ACC) of 85% and information transfer rate (ITR) of 102 bits per minute (bpm), whereas the calibrated BCI (CS-wcCCA) applying also CR at 62% achieved ACC of 85% and ITR of 195 bpm. As a hilghlight, the proposed BCI allows significant reduction of the transmitted file size, and improves the communication latency that may be useful in remote and Cloud robotics applications, such as for users with severe motor disabilities, to train driving safely robotic wheelchairs via IoT.

The application of the brain-computer interface (BCI) is massively helpful and advantageous for disabled people. Moreover, BCI is an arrangement of software and hardware interface that provides a direct interaction between the human brain and computer devices. Therefore, in this article, A steady state visual evoked potential (SSVEP)-based BCI system is presented to identify SSVEP components from multi-channel electroencephalogram (EEG) data by minimizing background noise using an adaptive spatial filtering method. Here, the proposed adaptive spatial filtering-based SSVEP component extraction (ASFSCE) model improves reproducibility among multiple trails and identifies targets efficiently by optimizing the Eigenvalue problem. Along with that, the proposed ASFSCE model minimizes computational complexity from O(G<sup>2</sup>) to to get high target identification accuracy with faster execution. Performance results are measured using the SSVEP dataset. In this dataset, 11 subjects are used to perform experiments and 256-channel EEG data is taken. The efficiency of the proposed ASFSCE model is measured in terms of mean target detection accuracy and mean information transfer rate (ITR) in bits per minute. The average detection accuracy and ITR are evaluated by considering 23 trials for each subject. The obtained detection accuracy is 93.47% and ITR is 308.23 bpm.

Brain-computer interface (BCI) for robotic arm control has been studied to improve the life quality of people with severe motor disabilities. There are still challenges for robotic arm control in accomplishing a complex task with a series of actions. An efficient switch and a timely cancel command are helpful in the application of robotic arm. Based on the above, we proposed an asynchronous hybrid BCI in this study. The basic control of a robotic arm with six degrees of freedom was a steady-state visual evoked potential (SSVEP) based BCI with fifteen target classes. We designed an EOG-based switch which used a triple blink to either activate or deactivate the flash of SSVEP-based BCI. Stopping flash in the idle state can help to reduce visual fatigue and false activation rate (FAR). Additionally, users were allowed to cancel the current command simply by a wink in the feedback phase to avoid executing the incorrect command. Fifteen subjects participated and completed the experiments. The cue-based experiment obtained an average accuracy of 92.09%, and the information transfer rates (ITR) resulted in 35.98 bits/min. The mean FAR of the switch was 0.01/min. Furthermore, all subjects succeeded in asynchronously operating the robotic arm to grasp, lift, and move a target object from the initial position to a specific location. The results indicated the feasibility of the combination of EOG and SSVEP signals and the flexibility of EOG signal in BCI to complete a complicated task of robotic arm control.

BackgroundBridging the gap between laboratory brain-computer interface (BCI) demonstrations and real-life applications has gained increasing attention nowadays in translational neuroscience. An urgent need is to explore the feasibility of using a low-cost, ease-of-use electroencephalogram (EEG) headset for monitoring individuals’ EEG signals in their natural head/body positions and movements. This study aimed to assess the feasibility of using a consumer-level EEG headset to realize an online steady-state visual-evoked potential (SSVEP)-based BCI during human walking.MethodsThis study adopted a 14-channel Emotiv EEG headset to implement a four-target online SSVEP decoding system, and included treadmill walking at the speeds of 0.45, 0.89, and 1.34 meters per second (m/s) to initiate the walking locomotion. Seventeen participants were instructed to perform the online BCI tasks while standing or walking on the treadmill. To maintain a constant viewing distance to the visual targets, participants held the hand-grip of the treadmill during the experiment. Along with online BCI performance, the concurrent SSVEP signals were recorded for offline assessment.ResultsDespite walking-related attenuation of SSVEPs, the online BCI obtained an information transfer rate (ITR) over 12 bits/min during slow walking (below 0.89 m/s).ConclusionsSSVEP-based BCI systems are deployable to users in treadmill walking that mimics natural walking rather than in highly-controlled laboratory settings. This study considerably promotes the use of a consumer-level EEG headset towards the real-life BCI applications.

A brain computer interface (BCI) is a real-time communication system designed to allow users to voluntarily send messages or commands without sending them through the brain's normal output pathways. We designed a real-time BCI platform based on Android. A equipment that uses the human to control a portable device through some electroencephalographic (EEG) rhythms has also been presented. The neural signals obtained by EEG recording equipment are sent through a Web Service technology connection to a PC that processes it in real time and sends it wirelessly to Android. Web Service has been used as a wireless technology for sending EEG signals to a PC and vice versa, the Android gets the command from the PC though the Web Service technology, which has been proposed and furthers it showing that the system is reliable and robust enough to work in BCI systems. In this study we have investigated the human’s ability to application by manipulating neuronal motor cortex activity in the presence of a visual feedback environment. This paper presents one of these solutions, which control application by BCI based on motor imagery. This type of BCI solution is translating the motor imagery EEG into three control signals: left, right or transmutation. And then use it as an input device of application to realize the function of operating. The Android digitizes and stores the EEG signal, and exports the results of Signal Analysis on the Monitors to achieve the basic function which is application through the human’s ideas. COM technology allows the BCI platform has strong scalability to meet the needs of various types of brain computer interface solution for the application, and the result is cheering.

A novel hybrid BCI speller based on RSVP and SSVEP paradigm

Recently, brain-computer interface (BCI) systems developed based on steady-state visual evoked potential (SSVEP) have attracted much attention due to their high information transfer rate (ITR) and increasing number of targets. However, SSVEP-based methods can be improved in terms of their accuracy and target detection time. We propose a new method based on canonical correlation analysis (CCA) to integrate subject-specific models and subject-independent information and enhance BCI performance. We propose to use training data of other subjects to optimize hyperparameters for CCA-based model of a specific subject. An ensemble version of the proposed method is also developed for a fair comparison with ensemble task-related component analysis (TRCA). The proposed method is compared with TRCA and extended CCA methods. A publicly available, 35-subject SSVEP benchmark dataset is used for comparison studies and performance is quantified by classification accuracy and ITR. The ITR of the proposed method is higher than those of TRCA and extended CCA. The proposed method outperforms extended CCA in all conditions and TRCA for time windows greater than 0.3 s. The proposed method also outperforms TRCA when there are limited training blocks and electrodes. This study illustrates that adding subject-independent information to subject-specific models can improve performance of SSVEP-based BCIs.

Brain Painting: Usability testing according to the user-centered design in end users with severe motor paralysis