A Novel TSV Model With Fault Characterization for High-Frequency Transmission in 3D ICs

The pre-bond through silicon via (TSV) probing tests and fault localization are important for yield assurance in 3D-SICs. This paper proposes an optimization algorithm to generate the preferable set of test sessions for pre-bond TSV probing tests. Test sessions generated by the optimization algorithm can not only get localization of faulty TSVs in TSV network, but also reduce test time and cost of the pre-bond TSV test. By using the proposed optimization algorithm, the reduction in pre-bond TSV test time is 10% for the pinpointing of four faulty TSVs in 13-TSV network and even 20.5% for one faulty TSV in 6-TSV network compared to the original one [4].

Three dimensional integrated circuits (3D ICs) have been proposed as a solution for the limitation of microfabrication technology. However, through-silicon via (TSV), which connects two different dies vertically, may fail, and it can decrease the yield of 3D-ICs. A novel TSV repair architecture to repair defect TSVs is proposed in this paper. By shifting the corresponding signals of the faulty TSVs vertically and diagonally to the non-faulty TSVs, the proposed method maintains repair rate of TSV to 88.6% when there are 8 faulty TSVs. The hardware area of MUXs in proposed method is 193.6μm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> while that of the previous work is 245.8spl mu/m <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> and 297.9 spl mu/m <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> .

Through-silicon via (TSV) based 3D integrated circuit (IC) testing is promising area to the researchers in modern day semiconductor industry. The manufacturing of 3D ICs may produce TSV defects which reduce yield. Recent work has proposed grouping of functional and redundant TSVs such that the faulty functional TSVs are supported by redundant TSVs and multiplexers (MUXs) are used to implement that group. This paper proposes grouping of functional and redundant TSVs such that a functional TSV is supported by redundant TSVs of other groups. We have presented an algorithm that finds the best grouping of functional and redundant TSVs such that maximum recovery of functional TSVs can be achieved with a given number of MUXs.

Design of through-Silicon-Via (TSV) based 3D IC is became feasible recently. Testing of TSVs is an important issue in this respect. It is a challenge to test the TSVs before the bonding of different layers so that the manufacturing defects of TSV can be identified properly. In this paper, we are trying to test the TSVs before bonding. Here we have proposed a heuristic algorithm to locate the faulty TSVs uniquely and at the same time it reduces the test time significantly for locating those faulty TSVs. Simulation results how that our algorithm achieved up to on an average 33% reduction in test time for a 20 TSV network than serial testing approach. Our algorithm also performs better in terms of est time reduction than the previous work present in the literature.

3D IC technologies are now approaching the innovation and business activities of semiconductor industries. 3D IC can be heterogeneous from different chip, interposer or substrate to integrate into a single package by using through silicon via (TSV) technique. With increasing functionality and performance at minimum cost and power dissipation, wide I/O memory VLSI technologies are being aggressively scaled to meet this demand. Stack memory chips using TSV technique will lead to increase a significant manufacturing challenge for semiconductor industries. TSV formation and interconnected reliability on the intermetallic compound (IMC) between the metal-metal bounded micro-bumps are crucial for 3D IC technologies. As the number and power of IC increases, lots of heat will be generated and, in turn raises the junction temperature. This will greatly deteriorate the performance of IC. Heat dissipation for 3D IC, when the power density exceeds 100W/cm2, is an important design concern before marketing. In this paper, high density TSV formed by an ultrafast pico-second laser to evaluate the behavior between manufacturing process and silicon material is presented. In addition, thermal management using finite element analysis to predict the reliability of TSV model is demonstrated.

In this research, a BIST (built in self test) architecture for testing crosstalk effects in highly dense Through Silicon Via (TSV) placed in structured array form, in 3DICs (Three Dimensional integrated circuits), designed and simulated using the Xilinx ISE tool and the VHDL language. A novel methodology is proposed, and simulated, to observe the test responses of the victim TSVs in the chosen group simultaneously. Boundary-scan cell structures are modified, created for the purpose of operating in different modes such as shift, update and capture in either conventional serial shift mode as well as in proposed parallel broadcasting mode. Output Response Analyzers (ORA), or signature analyzers that have been simulation-verified. In this study, we suggested a novel encoder-based signature generator to locate faulty TSVs in the parallel-observed TSVs. This paper discusses the whole BIST architecture, the BIST controller built on an algorithmic state machine, the design of TPG (Test Pattern Generator), and the faulty TSV signature generator. Comparing the BIST architecture, to serial shift based interconnect tests done by IEEE 1149.1 (JTAG) such as EXTEST and IEEE 1838 standards, the test’s time complexity of BIST is relatively very low. The entire TSV array test is completed in just 32 clock cycles. The design is adaptable and can be used to broadcast test patterns to a group or to transmit test patterns serially using IEEE 1838 or 1149.1.

&lt;p&gt;Information technology-to-internet of things may have succeeded because of fast silicon chip capability expansion. Moore's law, which reduces device size, boosted integrated circuit (IC) performance. Delay rises with highdensity connection parasitic capacitance. Interconnect delays have surpassed transistor delays and slowed progress. An alternative is required now to reduce connection latency. The third dimension is used in popular 3D IC technology IC technology requires through silicon via (TSV) for signal integrity and heat mitigation. Noise coupling hinders electrical communication between signal-carrying TSVs (aggressive TSVs) and ground TSVs (victim TSVs), a 3D IC bottleneck. TSVs must be dielectrically insulated from Si substrates to avoid electrical signal interference. Additionally, first-order modelling will confirm the suggestions. This article proposes using the nanosheet field effect transistor (NSFET) to overcome 3D IC noise coupling and complementary metal oxide semiconductor (CMOS) technology nodes. After discussing the electronic industry and sub nm, several basic metrics and criteria for developing electronic components are presented. The first technique uses Perylene-N's exceptional noise-cancelling characteristics. Second technique uses electrical TSV (ETSV), thermal TSV (TTSV), and heat source models to measure noise coupling on numerous ICs. The third proposes many noise-reducing materials. The suggested structures outperform traditional approaches.&lt;/p&gt;

Through silicon via (TSV) based 3D integrated circuits have inspired a novel design paradigm which explores the vertical dimension, in order to alleviate the performance and power limitations associated with long interconnects in 2D circuits. TSVs enable vertical interconnects across stacked and thinned dies in 3D-IC designs, resulting in reduced wirelength, footprint, faster speed, improved bandwidth, and lesser routing congestion. However, the usage of TSVs itself gives rise to many critical design challenges towards the minimization of chip delay and power consumption. Therefore, realization of the benefits of 3D ICs necessitates an early and realistic prediction of circuit performance during the early layout design stage. The goal of this thesis is to meet the design challenges of 3D ICs by providing new capabilities to the existing floorplanning framework [87]. The additional capabilities included in the existing floorplanning tool is the co-placement of TSV islands with circuit blocks and performing non-deterministic assignment of signals to TSVs. We also replace the wirelength and number of TSVs in the floorplanning cost function with the total delay in the nets. The delay-aware cost function accounts for RC delay impact of TSVs on the delay of individual signal connection, and obviates the efforts required to balance the weight contributions of wirelength and TSVs in the wirelength-aware floorplanning. Our floorplanning tool results in 5% shorter wirelength and 21% lesser TSVs compared to recent approaches. The delay in the cost function improves total delay in the interconnects by 10% - 12% compared to wirelength-aware cost function. The influence of large coupling capacitance between TSVs on the delay, power and coupling noise in 3D interconnects also offers serious challenges to the performance of 3D-IC. Due to the degree of design complexity introduced by TSVs in 3D ICs, the importance of early stage evaluation and optimization of delay, power and signal integrity of 3D circuits cannot be ignored. The unique contribution of this work is to develop methods for accurate analysis of timing, power and coupling noise across multiple stacked device layers during the floorplanning stage. Incorporating the impact of TSV and the stacking of multiple device layers within floorplanning framework will help to achieve 3D layouts with superior performance. Therefore, we proposed an efficient TSV coupling noise model to evaluate the coupling noise in the 3D interconnects during floorplanning. The total coupling noise in 3D interconnects is included in the cost function to optimize positions of TSVs and

Through silicon vias (TSV) are an enabler for high performance Three Dimensional Integrated Circiuts (3DIC). TSVs are used for signal, power and ground lines in 3DICs. TSVs used to carry signals can induce noise in nearby circuitry and in those instances shielding is required. Traditional shielding is composed of guard rings surrounding the signal TSVs or if the signal is differential in nature, a careful arrangement of TSVs carrying the differential signals can aid in noise reduction. In the guard ring scenario, the guard rings are typically tied to ground. This paper proposes a technique for energy scavenging utilizing the guard rings for shielding TSVs. Energy absorbed by the guard rings can be stored for later use by the system. This paper examines the feasibility of configuring the guard rings to charge a decoupling capacitor instead of shunting energy to ground. It is shown that the decoupling capacitor can be charged using this method and that under certain conditions, the overall power of the system can be reduced by 4% to 15%

Convergence and miniaturization of consumer electronic products such as cameras, phones, etc. has been driven by enhanced performance and reduced microelectronics size. For past few decades Moore’s law has been driving the microelectronics industry to achieve high performance with small form-factors at a reasonable cost. While the continued miniaturization of the transistors has resulted in unparalleled growth of the electronics industry, further performance increment via size scaling could be cost-ineffective and difficult to manufacture. To satisfy the current/future integrated Circuit (IC) package requirements, vertical integration of chips holds the key, i.e., 3-D packaging. Chip-stacking (3-D) is emerging as a powerful technology to reduce package footprint, decrease interconnection power, higher frequencies, and provide efficient integration of heterogeneous devices. It allows further reduction in the form factor of current systems and eases the interconnect performance limitation since the components are integrated on top of each other instead of side-by-side, resulting in shorter interconnect lengths. Due to high package density and chip-stacking on top of each other, heat dissipation from the stacked chips becomes a concern. To overcome these thermal challenges and provide shorter/faster inter-chip electrical connection, Through Silicon Via (TSV) technology is being implemented in 3-D ICs. TSVs allow 3-D chips to be interconnected directly and provide high speed signal propagation. TSVs provide inter-chip heat/current path but the current flowing through the TSVs results in localized heat generation (Joule Heating) within the silicon, which could be detrimental to the overall performance of the system. In this paper, the effect of Joule heating on the device performance measured by trans-conductance, electron mobility (e− mobility), and channel thermal noise is analyzed. Thinned (100 μm) chips with a uniform power map and evenly distributed TSVs are analyzed in this work. Thermal distribution in the package is studied for different TSV currents including a base-line case of no-current (thermal TSV only) and the junction temperature is determined for each case. The response from the thermal analysis is correlated to the device performance through existing relations. Results indicate that joule heating has a significant effect on the thermal response of the 3D IC and subsequently proves to be detrimental to the chip performance. An understanding of the electrical performance dependence on TSV joule heating is developed through this work.

Through silicon via (TSV) based 3-dimensional integrated circuit (3D IC) has become the key solution to satisfy continuously increasing demands for small form factor, wide bandwidth, high performance, and low power consumption on electronic devices. However, there still remain several challenges to be solved; one of the most significant issues in 3D IC is TSV to active circuit noise coupling. In this paper, we analyzed the noise coupling between TSV and LC-VCO, which is an important component in RF communication system. When TSV is located near LC-VCO, the noise can easily travel through silicon substrate to the body of MOSFETs in LC-VCO. The noise coupling mechanisms of TSV to PMOS and NMOS are analyzed by voltage transfer functions in frequency-domain obtained by 3D electromagnetic solver simulation. The voltage transfer function between TSV and MOS is analyzed under variations of several physical parameters to clarify the tendencies of noise coupling. In addition, the noise coupling effect on PMOS and NMOS in LCVCO are investigated and compared in terms of sensitivity, such as phase noise.

Through silicon via (TSV) is one of the key components of the emerging 3D ICs. However, increasing number of TSVs in smaller silicon area leads to some severe negative impacts on the performance of the 3D IC. Growing signal integrity issues in TSVs is one of the major challenges of 3D integration. In this paper, different materials for the cores of the vias and the interposers are investigated to find the best possible combination that can reduce crosstalk and other losses like return loss and insertion loss in the TSVs. We have explored glass and silicon as interposer materials. The simulation results indicate that glass is the best option as interposer material although silicon interposer has some distinct advantages. For via cores three materials — copper (Cu), tungsten (W) and Cu-W bimetal are considered. From the analysis it can concluded that W would be better for high frequency applications due to lower transmission coefficient. Cu offers higher conductivity, but it has larger thermal expansion coefficient mismatch with silicon. The performance of Cu-W bimetal via would be in between Cu and W. However, W has a thermal expansion coefficient close to silicon. Therefore, bimetal Cu-W based TSV with W as the outer layer would be a suitable option for high frequency 3D IC. Here, we performed the analysis in terms of return loss, transmission coefficient and crosstalk in the vias.

The rise of three-dimensional (3D) IC layouts necessitates the development of unique partitioning methods that will be suitable for the 3D component designs. Net lists partitioning is a key aspect of the physical design of a 3D IC. Reducing wire lengths between gates is possible with 3D-ICs since they have a small footprint as well as vertical connectivity among dies. As a result, they consume less power and have shorter connection delays. This paper presents an efficient genetic algorithm (GA) based layer partitioning technique for 3D ICs that focuses on proper layer assignment to reduce area deviation and minimization of Through Silicon Vias (TSVs) to reduce IC footprint. The method starts with random initial solutions and refines the solutions with efficient crossover and mutation operator till the optimized solution is achieved. Our methodology produces high-quality solutions on well-known benchmarks. The experimental findings are compared with state-of-the-art methodologies and the suggested strategy is found to be very effective in the case of decreasing the TSV count and space need of the 3-dimensional IC design. In addition, the performance of our strategy is also compared with two recent publications that use GA and Particle Swarm Optimization (PSO) and it is found that the proposed method achieves 20.18% and 38.66% average reduction in terms of TSV count respectively. Thus, the suggested technique is beneficial for multilayered 3D IC partitioning, as it can reduce TSV count while also satisfying balancing criteria and latency.

This paper reports on a new type of through-silicon via (TSV) defect, silicon fin defect, which was found after TSV deep-reactive-ion-etching (DRIE) process for TSV integration with front-end-of-line (FEOL) devices. One possible root cause for this defect is that the bulk micro defect (BMD) in silicon substrate serves as a micro-mask during etching and results in silicon fin defects at TSV bottom. These defects have to be eliminated as they are killer TSV defects for several reasons: (1) could serve as a weak point for isolation liner deposition; (2) could be a weak point for barrier/seed layer deposition; and (3) may cause mechanical failures during TSV backside reveal. Previously, silicon fin defects were removed by switching to a non-BMD silicon substrate for interposer application. However, for TSV integration with FEOL devices, the BMD layer serves as an intrinsic gettering layer for devices, therefore, it cannot be removed from the silicon substrate, which makes it challenging to get rid of silicon fin defects. In order to establish a non-destructive in-line detection method of the fin defects, scanning electron microscope (SEM) automatic process inspection (API) was set up to image the fin defects at the bottom of the trench. A special working point with high depth of focus (DoF) and contrast was created to obtain good top-down SEM imaging of the defects at the bottom of this high-aspect-ratio (HAR) structure. Three types of silicon substrates (A, B, and C) were used for this study to investigate the potential root cause. SEM API results show defect rates of 20%, 3.3% and 0% for substrates A, B, and C, respectively. This is in good agreement with both BMD simulation results and benchmarking data in which substrates A, B, and C had normalized BMD densities of 11.7, 5.74, and 1 cm-3, respectively, with a comparable BMD size of 80~90 nm and a denuded zone (DNZ) depth of 10~15 μm. The correlation between BMD density in a silicon substrate and silicon fin defect rate indicates that BMD is a key root cause for silicon fin defects. To eliminate silicon fin defects, an optimized DRIE process has been developed. On the same type of substrate, the DRIE process with a typical voltage bias results in a defect rate of 6.7%, while no silicon fin defect was detected out of 200 TSVs with a polynomial bias ramp to relatively higher final voltage bias during the last 15 μm etch. The hypothesis is that higher voltage bias is able to sputter away BMD and shows potential to get rid of the silicon fin defects at the TSV bottom. In summary, a capable inspection method, a preferred silicon substrate with BMD spec range, and a promising way for DRIE process optimization to eliminate the silicon fin defect at the TSV bottom have been identified and developed in this work. Detailed results and analysis, particularly the fin defect images, statistical inspection results, BMD benchmarking data, simulation results, and TSV profile with optimized process will be discussed in the paper.

In three-dimensional integrated circuit (3D-IC) systems that use through-silicon via (TSV) technology, a significant design consideration is the coupling noise to or from a TSV. It is important to estimate the TSV noise transfer function and manage the noise-tolerance budget in the design of a reliable 3D-IC system. In this paper, a TSV noise coupling model is proposed based on a three-dimensional transmission line matrix method (3D-TLM). Using the proposed TSV noise coupling model, the noise transfer functions from TSV to TSV and TSV to the active circuit can be precisely estimated in complicated 3D structures, including TSVs, active circuits, and shielding structures such as guard rings. To validate the proposed model, a test vehicle was fabricated using the Hynix via-last TSV process. The proposed model was successfully verified by frequency- and time-domain measurements. Additionally, a noise isolation technique in 3D-IC using a guard ring structure is proposed. The proposed noise isolation technique was also experimentally demonstrated; it provided -17 dB and -10dB of noise isolation between the TSV and an active circuit at 100 MHz and 1 GHz, respectively.