A Spectral-Efficient Transmission Scheme for Dimmable Visible Light Communication Systems

Smart city planners pay more attention towards visible light communication (VLC) system to achieve seamless high speed connectivity. A light emitting diode (LED) acts as a transmitter in VLC system. However, the nonlinear characteristics and dimming nature of LED limits the performance of the VLC system by degrading the quality of transmitted signal. In this paper, we propose an adaptive-learning-architecture (ALA) based predistortion technique to estimate and compensate for LED nonlinearities as well as increase the spectral efficiency of a VLC system. A DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM) signal is considered. The performance with and without predistorter is analysed assuming optical line-of-sight (LOS) channel. It is shown that degradation due to LED nonlinearity can be compensated by using ALA-based predistortion, and the overall Predistorter-LED system is able to approach near-linear performance. Further, we investigate the impact of dimming on the performance of nonlinear LED in VLC system. Simulation results based on symbol error rate (SER), amplitude distortion (AM/AM) curves and constellation plots validate the performance of our proposed technique.

Recently, multiple-input multiple-output (MIMO) has been proposed in visible light communications (VLC) systems to boost the data rate by utilizing spatial multiplexing. Unlike RF systems in VLC, lighting requirements, such as dimming control, should be taken into consideration for the design of a VLC transceiver. Moreover, VLC systems are inherently nonlinear and dynamic-range-limited. To drive an LED transmitter, the signal is bounded by a turn-on value and a saturation value. In this letter, we show how the dynamic-range constraint and dimming control impact the design of MIMO transceiver. Three different MIMO schemes are proposed and studied by theoretical analysis and simulation.

Multiple-input multiple-output (MIMO) technique is now used in most new broadband communication system, and orthogonal frequency division multiplexing (OFDM) is also utilized within current 4^th generation (4G) of mobile telecommunication technology. With MIMO and OFDM combined, visible light communication (VLC) system’s diversity gain is increase, yet system capacity for dispersive channels is also enhanced. Moreover, with the emerging massive MIMO-OFDM VLC system, there are significant advantages than smaller systems’ such as channel hardening, further increasing of energy efficiency (EE) and spectral efficiency (SE) based on law of large number. This paper addresses one of the major technological challenges, system architecture design, which was solved by semispherical beehive structure (SBS) receiver and so that diversity gain can be identified and applied in Massive MIMO VLC system. Simulation results shows that the proposed design clearly presents a spatial diversity over conventional VLC systems.

The exponential rise in wireless communication demands and allied applications have revitalized academia-industries to develop an efficient and potential solution. Furthermore, the high-pace increasing scarcity of radio spectrum has also alarmed researchers to achieve better Quality of Service (QoS) centric solution. To meet such demands Visible Light Communication (VLC) systems have gained global attention; however, up surging high rate, range and reliability (3R) needs demand better performance. Towards these goals, Multiple Input Multiple Output (MIMO) based VLC systems is an efficient approach; though its efficacy under Multiple Users (MU) conditions remains least explored. Enabling MIMO-MU based VLC can achieve 3R objectives effectively; however, factors like multipath attenuation, interferences and varied impairment-affects makes classical approached confined. The MIMO-MU VLC systems require robust error, noise or interference resilient transmission even under adverse conditions such as non-linear LED, multipath attenuation and interference. Towards these objectives, in this paper a highly robust MIMO-MU VLC system is developed that incorporates an augmented MIMO channel design and combined pre-coding and post equalization schemes. To alleviate major interference probability in MIMO-MU environment, proposed model incorporates time (delay)-multiplexing based data transmission followed by signal adaptive precoding and Volterra Kernel based Hybrid-equalizer. This approach enables interference and noise removal as well as LED non-linearity handling under MIMO-MU VLC communication. The use of a Volterra Kernel based Decision Feedback Equalization with both linear as well as non-linear equalization enables proposed VLC system to exhibit low Bit Error Rate with low modulation index and taps, that optimizes trade-off between performance as well as complexity.

In this paper, we propose a dimmable visible light communication (VLC) system based on spectral-efficient layered/enhanced asymmetrically clipped optical single-carrier frequency-division multiplexing (L/E-ACO-SCFDM). L/E-ACO-SCFDM superimposes multi-layer ACO-SCFDMs occupying different subcarriers for enhancing the spectral efficiency of the system. Both the adjustable layer polarities and the low peak-to-average-power ratio property of ACO-SCFDM make it better suited to the linearity-limited VLC system. Meanwhile, L/E-ACO-SCFDM has the signal-to-noise ratio averaging advantage, which can effectively resist the high-frequency distortion caused by the bandwidth limitation of the VLC system. Based on the maximization of spectral efficiency of the system, the layer amplitudes, layer spectral efficiencies, and bias voltage are jointly optimized for providing the efficient communication under different illumination requirements. Benefiting from the numerous strengths, the proposed L/E-ACO-SCFDM-based dimming scheme can achieve at least 22.0% average spectral efficiency gain compared with several state-of-the-art OFDM-based dimming schemes within the same dimming range, which shows the great superiority for future practical applications of VLC.

A new precoding scheme for spectral efficient optical OFDM systems

SummaryWith the development of new generation lighting sources, visible light communication (VLC) system has become a complementary solution to traditional radio frequency wireless system. However, the error performance of VLC system is degraded because of multipath effects and interference from other lighting sources that, in turn, reduce the communication range. This work targets the issue of performance degradation of VLC systems in terms of communication range and demonstrates a VLC system design that utilizes forward error correction (FEC) codes as the main tool to fix this issue. Furthermore, the work also covers practical implementation of the proposed VLC system using UART modules programmed in MATLAB. The hardware results demonstrate that the communication range of the proposed VLC system is enhanced up to 0.5 m. Over and above, it is also shown through simulations that the coding gain of the proposed design is more when compared with existing VLC system(s).

While the traditional Visible Light Communication (VLC) system has attracted a lot of research attentions on boosting throughput, using Commercial Off-The-Shelf (COTS) devices, e.g. existing cameras on the smartphones, is a recent trend to implement readily deployable VLC systems. In particular, since LED-Camera VLC systems have shown a promising potential in large indoor communication due to the growing deployment of LED lighting infrastructure, a comprehensive VLC system with cooperative transmission and roaming support has become an impending need. To this end, we propose a novel VLC and visible light sensing (VLS) system to address that by leveraging LED sensing and effective encoding/decoding schemes. It is achieved first by utilizing LED sensing via converting parts of LED luminaire into light sensors to detect diffuse reflection change caused by presence of the user. After the users are detected and located, the system employs rateless codes and newly designed code assignment scheme to collaboratively transmit to detected users in their communication cells. We believe the proposed system has the potential to a roaming support VLC system in the whole building or indoor areas.

• Core Innovation & Objective • Developed a novel, integrated system architecture combining a modified USRP X310 software-defined radio platform with a custom-designed high-power LED optical transceiver. • Achieved high-speed, low-latency, and highly reliable audio-video transmission over Visible Light Communication (VLC) for intelligent transportation and vehicle-to-vehicle (V2V) applications, particularly in electromagnetically sensitive environments. • Key Technical Breakthroughs • LED Bandwidth Extension: Designed an innovative active pre-equalization circuit (based on a 4th-order high-pass RC bypass and op-amps) that dramatically increased the 3dB modulation bandwidth of a commercial 15W LED from 3 MHz to 120 MHz. • High-Speed Modulation: Successfully implemented 64QAM-OFDM modulation/demodulation using GNU Radio on the USRP, enabling spectrally efficient data transmission. • Advanced Optical Design: Custom-designed optical lenses (transmitter and receiver) and a high-power Bias-T circuit for efficient AC/DC coupling, ensuring the LED operates in its linear region and maximizing optical power transfer. • Stable Link Performance: Incorporated an Automatic Gain Control (AGC) circuit at the receiver, stabilizing the output voltage between 1.2V - 2.0V and maintaining a modulation signal-to-noise ratio (SNR) > 23 dB over varying distances. • Outstanding System Performance • The experimentally demonstrated performance metrics are exceptional for a VLC system: • Peak Data Rate: 500 Mbps • Communication Distance: 0 - 110 meters • Bit Error Rate (BER): As low as 1.74 × 10⁻⁵ (far below the 1 × 10⁻⁴ target) • End-to-End Latency: < 0.1 s • Beam Angle: 11.5° (Transmitter) • Field of View (FOV): ≤ 18° (Receiver) • System Integration and Design • Hardware-Software Co-Design: Seamless integration of the USRP X310 (handling digital baseband processing) with the custom analog optical front-end. • Compact and Practical: The system is designed for external mounting on vehicles, offering a practical solution for real-world deployment. • Simulation-Guided Design: Used LightTools for optical design and Optisystem for communication link simulation to validate the design before implementation. • Significance and Application Value • Solves Critical Challenges: Provides a high-speed, secure, and EMI-free communication alternative to traditional RF in environments like military operations, petroleum facilities, and intelligent transportation systems. • 6G Potential: Serves as a practical reference for the development of VLC as a complementary technology in 6G networks. • Demonstrates Feasibility: Successfully proves the viability of using commercial LEDs and USRP platforms for building high-performance, medium-to-long-range optical communication systems. • This work represents a significant step forward in practical high-speed VLC system design, combining theoretical innovation with robust engineering to achieve state-of-the-art performance. Existing vehicular VLC systems suffer from limited bandwidth, short transmission distances, low data rates, and support only a narrow range of communication services. To address these issues, this paper proposes a vehicle-mounted high-speed LED visible light communication (VLC) system based on Universal Software Radio Peripheral (USRP). Leveraging 64QAM-OFDM digital modulation, an improved USRP X310 hardware platform, and a PC, we establish a novel architecture comprising digital baseband and optical transceiver modules. The baseband module eliminates traditional spectrum-shifting circuits and antennas, retaining only FPGA and ADC/DAC units. Audio/video files undergo 64QAM-OFDM modulation directly on the PC, with modulated signals output via DAC to a custom-designed wide-bandwidth LED transceiver. A broadband hardware equalization network based on a fourth-order RC bypass circuit was designed expands the 3dB bandwidth of high-power LEDs from 3 MHz to 120 MHz. Combined with automatic gain control (AGC), this achieves an optical transceiver with 12–15 W output power, >23 dB optical modulation signal-to-noise ratio (SNR), and stable receiver output voltage (1.2–2.0 V). The resulting compact system delivers low latency, high data rates, and high reliability. Under aligned optical path conditions, the system achieves >1 Mbit/s at 110 m (BER 0.49 × 10⁻⁵, delay 0.009-0.05s) and a peak rate of 500 Mbit/s at 10 m (BER 7.4 × 10⁻⁵), with an 11.5° transmit angle and a receiver field of view (FOV) of less than 18°. This work demonstrates the feasibility of high-power LED-based 64QAM-OFDM communication using USRP X310 for medium- to long-range vehicular links, providing a reference for intelligent transportation systems.

We investigate the performance of visible light communication (VLC) system with a pulse width modulation (PWM) dimming control scheme. Under this scheme, the communication quality in terms of number of transmitted bits and bit error rate (BER) of less than 10(-3) should be guaranteed. However, for on-off-keying (OOK) signal, the required data rate becomes 10 times as high as the original data rate when the duty cycle of dimming control signal is 0.1. To make the dimming control scheme easy to be implemented in VLC system, we propose the variable M-QAM OFDM VLC system, where M is adjusted according to the brightness of LED light in terms of duty cycle. The results show that with different duty cycles the required data rates are not higher than the original value and less LED lamp power is required to guarantee the communication quality, which makes the dimming control system that satisfies both communication and illumination requirements easy to be implemented and power-saving.

A number of binary modulation schemes are proposed for LED based Visible Light Communication (VLC) systems to jointly achieve data transmission and brightness control. These binary modulation based solutions are spectrally inefficient because they consider the LED light source as single device. We observe that most of the commercial LED lights use more than one LED per light source and the possibility of individual current control of these LEDs would provide better brightness control resolution as well as higher data transmission rates. To achieve this we propose multi-level multi-pulse position modulation block coding scheme to jointly control multiple LEDs providing flicker free VLC link. The brightness level of the light source is controlled based on the number of LEDs switched on simultaneously. New algorithms are developed for symbol encoding/decoding as well as to enumerate the maximum number of symbols that can be encoded for the selected brightness level and the number of levels. Improvement in spectral efficiency is analyzed and compared with the contending binary modulation schemes.

The filtered‐orthogonal frequency division multiplexing (F‐OFDM) scheme has gained attention as a promising solution in the field of visible light communication (VLC) systems. One crucial aspect in VLC is the conversion of the complex F‐OFDM signal into a real signal that corresponds with direct detection and intensity modulation. Traditionally, achieving a real F‐OFDM signal has involved imposing Hermitian symmetry (HS) on the samples of the Inverse Fast Fourier transform (IFFT), which requires 2N‐point IFFT and obtains an N‐point FFT, thus adding complexity. In this study, a novel approach is presented and implemented, aiming to enhance spectral efficiency and reduce system complexity by generating a real F‐OFDM signal without relying on HS. This approach is then compared with HS‐free (HSF)‐OFDM, direct current biased optical OFDM, and asymmetrically clipped optical OFDM. The suggested method offers a remarkable improvement of ~50% in the required IFFT/FFT volume. Consequently, this method reduces hardware complexity and power usage compared with the traditional F‐OFDM method. Moreover, regarding error rates, the proposed method demonstrates better spectral efficiency than HSF‐OFDM.

Power control technology is necessary in Visible Light Communication (VLC) systems because of the multipath distortion and shadowing. When a power control algorithm is applied to the system, feedback error is inevitable. In this paper, we analyze the closed-loop power control algorithm and the influence of the power control error (PCE) in VLC systems. To analyze the effect of the PCE in VLC systems, the proposed system is studied with different modulation schemes and coding rates in terms of BER.

Visible light communication(VLC), which combines communication and illumination, is regarded as a potential wireless communication. For illumination requirements of VLC systems, dimming control is a significant function. Many schemes have been proposed for multi-input multi-output (MIMO) VLC systems or dimmable VLC systems, but few schemes combine the two. The dimming control scheme that has been proposed for MIMO-VLC systems in the reference still has a probability for improvement in spectral efficiency and error performance. This paper proposes a dimming control scheme that utilizes the constant weight space-time codes (CWSTC) to improve spectral efficiency and error performance for MIMO-VLC systems. Simultaneously, we also present the codeword structure and a low implementation complexity detection algorithm for the scheme. Finally, performance analysis and simulation results provide comparisons between the proposed scheme and other existing dimming control schemes.

In a visible light communication (VLC) system, the modulation bandwidth of light emitting diode (LED) is limited with current technology. In addition, the nonlinearity inherited in the LED prevents the application of spectral efficient modulation schemes with high peak-to-average power ratio. These characteristics limit the overall throughput of the VLC system. In this letter, a one-bit sigma-delta modulator (SDM) is introduced to the transmit signal. Such modification is compatible with the current LED lighting systems and LED drivers as the output of the one-bit SDM is equivalent to ON-OFF keying signal, thus is immune to system nonlinearities. In addition, the output of the one-bit SDM enjoys high spectral efficiency as the original input signal does. The out-of-band quantization noise can be taken care of at the receiver with analog filtering and digital signal processing. Simulation and experiment results validate that the SDM can significantly improve the VLC system performance.