High purity bright single photon source

Single photons are the key ingredient for many photonic quantum technologies including quantum key distribution and measurement-based quantum computing. However, it remains difficult to create devices with the appropriate specifications for use in non-laboratory environments. The optical microcavity platform provides an attractive route towards a room temperature single photon source device. Our ultra-small focused ion beam (FIB) milled open-access cavities offer enhancement of the spontaneous emission rate, tunability of the emission spectrum and increased light collection. The embedment of solid-state emitters within these cavities enables us to create a robust room temperature single photon source device, with the potential for high efficiencies and single photon purities. Defects such as the nitrogen-vacancy (NV) centre in diamond have been shown to be stable room-temperature sources of single photons. There are new single emitters emerging in two-dimensional materials such as hexagonal boron nitride (hBN). Here we present developments in room-temperature coupling of single defects to open-access microcavities of a planar-hemispherical geometry with mode volumes down to λ3. We report enhancements in the spectral density of photons into a single cavity mode, combined with improved single photon purities. It will be shown that the NV-cavity system provides a ~3% single photon emission efficiency with purities of up to 94%. The hBN-cavity system provides count rates >1Mcts/s into a single cavity mode with purities up to 96%. With these high single photon purities, such devices would be robust against photon number splitting attacks making them attractive for applications in quantum cryptography.

A single-photon source is realized with a cold atomic ensemble (87Rb atoms). A single excitation, written in an atomic quantum memory by Raman scattering of a laser pulse, is retrieved deterministically as a single photon at a predetermined time. It is shown that the production rate of single photons can be enhanced considerably by a feedback circuit while the single-photon quality is conserved. Such a single-photon source is well suited for future large-scale realization of quantum communication and linear optical quantum computation.

This thesis covers the development and the characterization of a single photon detector based on a superconducting microcalorimeter. The detector development is motivated by the Any Light Particle Search II (ALPS II) experiment at DESY in Hamburg, which searches for weakly interacting sub-eV particles (WISPs). There- fore, a detection of low-fluxes of 1064 nm light is required. The work is divided in three analyses: the characterization of a milli-kelvin (mK) cryostat, the character- ization of superconducting sensors for single photon detection, and the determina- tion of dark count rates concerning 1064 nm signals. Firstly, an adiabatic demagnetization refrigerator (ADR) is characterized, which allows to reach mK-temperatures. During commissioning, the ADR cryostat is op- timized and prepared to stably cool superconducting sensors at 80 mK 25 K. It is found that sensors can be continuously operated for 20 h before recharging the system in < 2 h. Furthermore, the adiabatic system reaches a chance of success of 80 % for a recharge without technical problems. Secondly, superconducting sensors are analyzed. The focus is on microcalori- metric transition-edge sensors (TESs) based on 20 nm Tungsten (W) films fabri- cated by the U.S. National Institute of Standards and Technology (NIST). NIST TESs have a near unity detection e ciency for 1064 nm light (literature value). The energy resolution for 1064 nm signals is measured to be < 8 %. The expo- nential falling time of a photon pulse is 1.5 s. Furthermore, by determining TES parameters, it is found that the linear TES theory describes measured photon pulses well. The TES response is read out by a superconducting quantum interference device (SQUID) fabricated by Physikalisch-Technische Bundesanstalt (PTB). The system bandwidth is measured to be 0.9 MHz. Finally, the operation in the ADR cryostat as well as the ALPS II laboratory is optimized. This setup forms the ALPS TES detector. Thirdly, the background is measured to obtain a dark count rate for 1064 nm signals. The ALPS TES detector is calibrated by a 1064 nm single photon source and methods are developed to analyze signals. In long-term measurements, back- ground events are measured by using di erent optical setups. By operating the TES without an optical link outside mK-environment, intrinsic background components are observed and classified. This results in an intrinsic dark count rate for 1064 nm signals of 1 : 0 10

The prototype of a quantum random number generator is a single photon which impinges onto a beam splitter and is then detected by single photon detectors at one of the two output paths. Prior to detection, the photon is in a quantum mechanical superposition state of the two possible outcomes with –ideally– equal amplitudes until its position is determined by measurement. When the two output modes are observed by a single photon detector, the generated clicks can be interpreted as ones and zeros – and a raw random bit stream is obtained. Here we implement such a random bit generator based on single photons from a defect center in diamond. We investigate the single photon emission of the defect center by an anti-bunching measurement. This certifies the “quantumness” of the supplied photonic input state, while the random “decision” is still based on the vacuum fluctuations at the open port of the beam-splitter. Technical limitations, such as intensity fluctuations, mechanical drift, and bias are discussed. A number of ways to suppress such unwanted effects, and an a priori entropy estimation are presented. The single photon nature allows for a characterization of the non-classicality of the source, and allows to determine a background fraction. Due to the NV-center’s superior stability and optical properties, we can operate the generator under ambient conditions around the clock. We present a true 24/7 operation of the implemented random bit generator.

As currently implemented, single-photon sources cannot be made to produce single photons with high probability, while simultaneously suppressing the probability of yielding two or more photons. Because of this, single photon sources cannot really produce single photons on demand. We describe a multiplexed system that allows the probabilities of producing one and more photons to be adjusted independently, enabling a much better approximation of a source of single photons on demand. The scheme uses a heralded photon source based on parametric downconversion, but by effectively breaking the trigger detector area into multiple regions, we are able to extract more information about a heralded photon than is possible with a conventional arrangement. This scheme allows photons to be produced along with a quantitative “certification ” that they are single photons. Some of the single-photon certifications can be significantly better than what is possible with conventional downconversion sources (using a unified trigger detector region), as well as being better than faint laser sources. With such a source of more tightly certified single photons, it should be possible to improve the maximum secure bit rate possible over a quantum cryptographic link. We present an analysis of the relative merits of this method over the conventional arrangement.

We describe the simplest single–photon encoding schemes and introduce the concept of a quantum optical gate. These gates can be used to build up arbitrary entangled states of many initially separate single photons. Experimental realization of such a gate involves the development of nonlinear phase shift elements sensitice at the single quantum level. We report our experimental efforts using linear optical elements and non–classical sources where we are able to demonstrate interference and entanglement of initially separate single–photon pulses.

Efficient sources of indistinguishable single photons are a key resource for various applications in fields like quantum sensing, quantum metrology and quantum information processing. In this contribution we report on single photon generation based on III-V semiconductor quantum dots (QDs). To increase the emission efficiency of single photons, it is essential to tailor the radiative properties of the quantum dot emitters by engineering their photonic environment. We present optimized single photon emitters being based on both micropillar and photonics crystal cavities, for applications in a vertical platform and on-chip in-plane platform, respectively. Electrically driven single photon sources with self assembled semiconductor QDs embedded into GaAs/AlAs micropillar cavities emit on demand net rates of ~35 MHz single photons, thus being well exploitable in quantum key distribution systems. In order to establish also a spatially deterministic fabrication platform, position controlled quantum dots are integrated into p-i-n micropillar cavities and single photon emission of a coupled QD-micropillar diode system is observed. Efficient broadband coupling of single photons into photonic crystal waveguides provides the basis for all on-chip quantum information processing, and an according approach is reported.

Single photon detectors are fundamental tools for quantum metrology, e.g. to calibrate both detectors and sources, as for quantum information. One of the most promising detectors able to resolve single photons is the transition-edge sensor (TES). We report our last results obtained with Ti/Au TES deposited on SiN substrate. Photon counting measurements, obtained by using pulsed sources, in the NIR-visible wavelength range, show the ability to resolve up to fourteen photons with an energy resolution of 0.44 eV at 690 nm (1.80 eV) and 0.38 eV at 1310 nm (0.95 eV), with a good linearity. A preliminary measurement obtained by using a parametric down conversion (PDC) heralded single photon source, at 812 nm (1.53 eV), is also reported.

Single photon frequency up-conversion and its applications

We report progress in the development of tunable room temperature triggered single photon sources based on single nitrogen-vacancy (NV) centres in nanodiamond coupled to open access optical micro-cavities. The feeding of fluorescence from an NV centre into the cavity mode increases the spectral density of the emission and results in an output stream of triggered single photons with spectral line width of order 1 nm, tunable in the range 640 - 700 nm. We record single photon purities exceeding 96% and estimated device efficiencies up to 3%. We compare performance using plano-concave microcavities with radii of curvature from 25 μm to 4 μm and show that up to 17% of the total emission is fed into the TEM00 mode. Pulsed Hanbury-Brown Twiss (HBT) interferometry shows that an improvement in single photon purity is facilitated due to the increased spectral density.

Heralded single-photon source (HSPS) with competitive single photon purity and indistinguishability has become an essential resource for photonic quantum information processing. Here, for the first time, we proposed a theoretical regime to enhance heralded single-photons generation by multiplexing the degree of the freedom of orbital angular momentum (OAM) of down-converted entangled photon pairs emitted from a nonlinear crystal. Experimentally, a proof-of-principle experiment has been performed through multiplexing three OAM modes. We achieve a 47$\%$ enhancement in single photon rate. A second-order autocorrelation function $g^{(2)}(0)<0.5$ ensures our multiplexed heralded single photons with good single photon purity. We further indicate that an OAM-multiplexed HSPS with high quality can be constructed by generating higher dimensional entangled state and sorting them with high efficiency in OAM space. Our avenue may approach a good HSPS with the deterministic property.

The integration of a single photon source based on a solid-state emitter with a photonic structure remains challenging and specifically when it comes to be compatible with optical fibres. It is important to do so for quantum technologies where single photon sources constitute building blocks for many technologies. In this work, we demonstrate the integration of a single photon source, made of a colloidal semiconductor nanocrystal, with a photonic structure made of a glass waveguide obtained by the ion-exchange technique, which is a fibre-compatible platform used in telecom photonics. Using surface functionalisation and a secondary waveguide of titanium dioxide, we manage to couple single photons from the nanoemitter to the optical waveguide. We observe the single photon character is preserved and demonstrates a 1.2 Purcell factor. A coupling efficiency over 25% is expected thanks to the titanium dioxide secondary waveguiding layer, compared to around 2% obtained for simply positioning the nanocrystal on top of the waveguide alone. The optical waveguide is then pigtailed to an optical fibre to demonstrate a first proof of principle of an integrated single photon source at room temperature with a fibre-compatible platform made of glass with a coupling efficiency increase of 2.8.

Based on the quantum dot-photon molecular coupling system, we proposed an efficient and stable single photon source. The system uses photon molecules formed by the coupling of two optical microcavities A and B, one of which contains a quantum dot. The excitation laser act on the quantum dot in cavity A, and through the interaction between the light field in cavity A and cavity B, single photon is generated in cavity B and output extraction is performed therein. The system maintains good sub-Poisson characteristics over a wide range of dot-cavity coupling strength variation (0.25κ<;g<;κ) and at low cavity tunneling strength (J≥0.5κ) as well. It also has excellent robustness and is easy to construct. Under the optimal experimental parameters that can be realized, the zero-delay second-order correlation function g <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> (0) of the system can be as low as 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-5</sup> with a relatively large intra cavity photon number. We theoretically explains the reason why the system produces sub-Poisson light, and analyzed the impact of system parameters change. Meanwhile, the system spatially separates the output light from the excitation light, making it easy to extract single photons, and has potential application value for easier integration. The model proposed in this paper will bring important guiding value to the efficient and integrated single photon sources in future quantum information processing.

Single photon sources, which are compatible with quantum memories, are important components of quantum networks. In this article, we show optical investigations on isolated GaAs/Al0.25Ga0.75As quantum dots grown via droplet epitaxy, which emit single photons on resonance with the Rb-87-D2 line (780 nm). Under continuous wave resonant excitation conditions, we observe bright, clean, and narrowband resonance fluorescence emission from such a droplet quantum dot. Furthermore, the second-order correlation measurement clearly demonstrates the single photon emission from this resonantly driven transition. Spectrally resolved resonance fluorescence of a similar quantum dot yields a linewidth as narrow as 660 MHz (2.7 μeV), which corresponds to a coherence time of 0.482 ns. The observed linewidth is the smallest reported so far for strain free GaAs quantum dots grown via the droplet method. We believe that this single photon source can be a prime candidate for applications in optical quantum networks.

In atomic-scale or quantum physics, an electromagnetic field is composed of photons, optical packets so small that a typical laser pointer with 1mW of power emits billions of them each second. Being able to take away or add a single photon in a light field at will would be useful for accurate engineering of quantum states. Such pure single photons are ideal for carrying and manipulating information in emerging quantum technologies, but generating them still is very challenging. In quantum physics, subtraction or addition of a photon is not a deterministic process. Instead, the probability is proportional to the number of photons originally in the electromagnetic field. This is described by the equation â|n〉 = √ n|n − 1〉 and â†|n〉 = √ n+ 1|n + 1〉, where â and ↠are annihilation and creation operators, respectively, representing the action of subtracting and adding a photon in a field composed of n photons.1 Such single-photon operations were limited to pure theoretical discussions until 2004, when Grangier and coworkers found a simple way to subtract a photon2 from a field. Passing through a beam splitter of high transmittivity, some photons can be split from the initial field. A ‘click’ detected in the photodetector in the reflected channel means one photon has been subtracted from the field: see Figure 1(a). When the initial field is composed of a small number of photons, the effect is dramatic and may even completely change the characteristics of the field. For example, let us take an initial single-mode squeezed state generated by ‘degenerate’ parametric down-conversion, which is an optical nonlinear process that converts a pump photon into two twin photons with half the pump photon energy. (This state is well known for its quantum noise squeezed into one quadrature at the expense of expanded noise in the other quadrature.) In order to visualize the noise properties and characteristics of the squeezed state, a probability-like function, such Figure 1. Setups to subtract (a) and add (b) a single photon from/to a light field. ρin and ρout denote the density operators of the input and output fields; BS is a low-reflectivity beam splitter; PDC is a nonlinear crystal where parametric down-conversion takes place; â and ↠denote on/off photodetectors.