• Home
  • Search
  • Multi-Objective Optimization of the Turning Process using the Probability Method
  • Cite Icon2
  • https://doi.org/10.48084/etasr.9472Copy DOI Icon

Multi-Objective Optimization of the Turning Process using the Probability Method

Show More
  • Abstract
  • Literature Map
  • References
  • Citations
  • Similar Papers
Abstract

This research aims to determine the optimal values of the cutting parameters when solving the turning process multi-objective problem. Three cutting parameters are considered in this study: spindle speed (nw), feed rate (f), and depth of cut (ap). A turning experiment series was conducted on a conventional lathe, with nine experiments having been designed according to the Taguchi experimental design matrix. In each experiment, the values of the three parameters changed and the material Removal Rate (Q) was measured. The Probability method was used to solve the multi-objective optimization problem. The Method based on the Removal Effects of Criteria (MEREC) technique was employed to calculate the weights of the criteria. The results of the optimization problem using the Probability method were also compared with those obtained using other methods, including the Simple Additive Weighting (SAW), Technique for Order Preference by Similarity to Ideal Solution (TOPSIS), Vlsekriterijumska optimizacijaI KOmpromisno Resenje (VIKOR), Multi-Atributive Ideal-Real Comparative Analysis (MAIRCA), Evaluation by an Area-based Method for Ranking (EAMR), Complex Proportional Assessment (COPRAS), Measurement Alternatives and Ranking according to Compromise Solution (MARCOS), Proximity Indexed Value (PIV), and Combined Compromise Solution (COCOSO). All the methods converged on the same unique solution to the multi-objective optimization problem. The optimal values for the parameters were: nw = 1350 rev/min, corresponding to a feed rate of 0.13 mm/rev, and a depth of cut of 0.4 mm. When machining with these optimal cutting parameters, the resulting values for Ra, RE, and Q were 1.057 µm, 0.03 mm, and 13225.68 mm²/min, respectively.

Similar Papers
  • Research Article

Evaluation and Ranking of Urban Drainage Systems Using SAW, TOPSIS, and VIKOR Methods: A Case Study in Bantul Regency

  • Oct 12, 2025
  • Applied Research in Science and Technology
  • Muhamad Arifin +2
  • Research Article
  • Citations17

On Solving Parametric Optimization Problem of an End Milling Process for Machining of Al 1070 using MCDM Techniques: A Comparative Analysis

  • May 29, 2023
  • Advances in Materials and Processing Technologies
  • Ranjan Kumar Ghadai +2
  • Research Article

Comparative Evaluation of Multi-Criteria Decision-Making Methods in the Online-CADCOM Platform

  • Dec 12, 2025
  • Proceedings of International Conference on Intelligent Systems and New Applications
  • Lavdim Menxhiqi
  • PDF
  • Research Article
  • Citations475

Are MCDA Methods Benchmarkable? A Comparative Study of TOPSIS, VIKOR, COPRAS, and PROMETHEE II Methods

  • Sep 20, 2020
  • Symmetry
  • Wojciech Sałabun +2
  • Research Article
  • Citations232

Erodibility prioritization of sub-watersheds using morphometric parameters analysis and its mapping: A comparison among TOPSIS, VIKOR, SAW, and CF multi-criteria decision making models

  • Oct 12, 2017
  • Science of The Total Environment
  • Alireza Arab Ameri +2
  • Research Article
  • Citations14

Evaluation of entropy-coupled multi-criteria decision-making methods for enhancing machinability

  • Sep 21, 2024
  • Heliyon
  • Nafisa Anzum Sristi +2
  • Research Article
  • Citations1

COMPARATIVE ANALYSIS OF MULTI-CRITERIA DECISION MAKING METHODS IN DETERMINING REDD+ PROJECT LOCATION

  • Aug 30, 2024
  • International Journal of Social Service and Research
  • Aditya Putra Irawan +1
  • Research Article
  • Citations106

Multi criteria decision making through TOPSIS and COPRAS on drilling parameters of magnesium AZ91

  • Oct 01, 2022
  • Journal of Magnesium and Alloys
  • M Varatharajulu +4
  • Research Article
  • Citations44

A Bayesian BWM and VIKOR-based model for assessing hospital preparedness in the face of disasters.

  • Nov 16, 2021
  • Natural Hazards
  • Halit Serdar Saner +2
  • PDF
  • Research Article
  • Citations36

Multiresponse Optimization of Process Parameters in Turning of GFRP Using TOPSIS Method

  • Oct 29, 2014
  • International Scholarly Research Notices
  • Arun Kumar Parida +1
  • Research Article
  • Citations3

Optimization of Machining Parameters for Nylon 6 Composite in CNC Lathe Using PCA-Based TOPSIS

  • Jan 01, 2018
  • International Journal of Manufacturing and Materials Processing
  • Vinay Bhardwaj +3
  • Research Article
  • Citations39

Erosion susceptibility mapping of sub-watersheds for management prioritization using MCDM-based ensemble approach

  • Jan 01, 2021
  • Arabian Journal of Geosciences
  • Biman Ghosh +1
  • Research Article
  • Citations6

A fuzzy based vertical handover network selection scheme for device-to-device communication

  • Jan 01, 2020
  • Indonesian Journal of Electrical Engineering and Computer Science
  • Meenakshi Subramani +1
  • Research Article
  • Citations140

Sub-basin prioritization for assessment of soil erosion susceptibility in Kangsabati, a plateau basin: A comparison between MCDM and SWAT models

  • May 16, 2020
  • The Science of the Total Environment
  • Raj Kumar Bhattacharya +2
  • Research Article

Comparing TOPSIS and VIKOR to prioritize international communication interventions across digital platforms

  • Mar 25, 2026
  • Scientific Reports
  • Yang Liu +2
Cactus Communications logo

Copyright 2026 Cactus Communications. All rights reserved.