Nine-coded compression technique with application to reduced pin-count testing and flexible on-chip decompression

A test pattern compression scheme for test data volume and application time reduction is proposed. While compression reduces test data volume, the increased number of internal scan chains due to an on-chip, fixed-rate decompressor reduces test application time proportionately. Through on-chip decompression, both the number of virtual scan chains visible to the ATE and the functionality of the ATE are retained intact. Complete fault coverage is guaranteed by constructing the decompression hardware deterministically through analysis of the test pattern set.

Scan architectures, though widely used in modern designs for testing purpose, are expensive in test data volume and power consumption. To solve these problems, we propose in this paper to modify an existing test data compression technique (Wang Z, Chakrabarty K in Test data compression for IP embedded cores using selective encoding of scan slices. IEEE International Test Conference, paper 24.3, 2005) so that it can simultaneously address test data volume and power consumption reduction for scan testing of embedded Intellectual Property (IP) cores. Compared to the initial solution that fill don't-care bits with the aim of reducing only test data volume, here the assignment is performed to minimize also the power consumption. The proposed power-aware test data compression technique is applied to the ISCAS'89 and ITC'99 benchmark circuits and on a number of industrial circuits. Results show that up to 14× reduction in test data volume and 98% test power reduction can be obtained simultaneously.

We present a test resource partitioning (TRP) technique that simultaneously reduces test data volume, test application time and scan power The proposed approach is based on the use of alternating run-length codes for test data compression. Experimental results for the larger ISCAS-89 benchmarks and an IBM production circuit show that reduced test data volume, test application time and low power scan testing can indeed be achieved in all cases.

Test access mechanism (TAM) optimization and test data compression lead to a reduction in test data volume and testing time for SOCs. In this paper, we integrate for the first time both these approaches into a single test methodology. We show, how an integrated test architecture based on TAMs and test data decoders can be designed. The proposed approach offers considerable savings in test resource requirements. Two case studies using the integrated test architecture are presented. Experimental results on rest data volume reduction, savings in test application time and the low test pin overheads for a benchmark SOC demonstrate the effectiveness of this approach.

Design for Testability (DFT) based on scan and ATPG has been adopted as a reliable and broadly acceptable methodology that provides very high test coverage, but for large circuits, the growing test data volume causes a significant increase in test cost because of much longer test time and elevated tester memory requirements. Test compression or scan compression provides great reduction in test data volume and test time required by adding on-chip decompressor and compactor. In this paper comparative analysis are made for Broadcast, XOR decompressor along with XOR, MISR and Hybrid compactors with respect to test coverage, test cycles required and test data volume by considering Flash Interface as CUT. From the experiments, it is observed that XOR decompressor with MISR compactor architecture provides 17.31% to 49.76% reduction in test data volume compared to other architectures, with 99.76% of fault coverage, 16694 test cycles and 2104µm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> of area overhead.

This paper presents a new test-data compression technique that uses exactly nine codewords. Our technique aims at precomputed data of intellectual property cores in system-on-chips and does not require any structural information of cores. The technique is flexible in utilizing both fixed- and variable-length blocks. In spite of its simplicity, it provides significant reduction in test-data volume and test-application time. The decompression logic is very small and can be implemented fully independent of the precomputed test-data set. Our technique is flexible and can be efficiently adopted for single- or multiple-scan chain designs. Experimental results for ISCAS'89 benchmarks illustrate the flexibility and efficiency of the proposed technique.

Scan design, providing a good test solution to sequential circuits, suffers large data volume, long test time and high test power problem. Recently, the random access scan (RAS) scheme offers a solution to alleviate the above problems (Baik et al., 2004). In this paper, based on RAS, a cocktail scan scheme is proposed and demonstrated to improve the test efficiency significantly. The scheme adopts a two-phase approach, firstly by using a cycle random scan test with a few random seed patterns to test the DUT and secondly, by using the RAS mechanism to test the circuit. Due to employment of a revised process and several strategies, namely, test response abundant, constrained static compaction, and bit propagation before test vector dropping, it is very effective in reducing bit flipping and test data volume, consequently, the test application time and power. Experimental results show that the scheme can achieve 86% reduction in test data volume and 10 times of speedup in test application time.

Testing chips is very critical to guarantee chips are fault-free before they are integrated in a system, so as to increase the reliability of the system. Although full-scan is a widely adopted design-for-test technique for LSI design and testing, the need for reducing the test data volume, scan-in power dissipation and test application time (VPT) of the full-scan designed chip is imperative. Based on the analysis of the characteristics of the variable-to-fixed run-length coding technique and the random access scan architecture, this paper presents a novel design scheme tackling all VPT issues simultaneously. Experimental results on ISCAS'89 benchmarks have shown on average 51.2%, 99.5%, 99.3% and 85.5% reduction in test data volume, average scan-in power dissipation, peak scan-in power dissipation and test application time, respectively.

In this paper, we propose a method of test compression for multiple scan designs. Instead of the conventional serial scan chains, the proposed method constructs scan trees in which scan flip-flops are placed and routed in a tree structure. Inputs of the scan trees drive several scan trees of different lengths (height). Since test data volume and test application time are dominated by the scan tree with the maximum height among the constructed scan trees, the proposed method distributes the scan flip-flops to the scan trees so as to minimize the maximum height of the scan trees. In addition, the proposed method modifies the given test vectors to maximize the reduction in test application time. Experimental results for ISCAS-89 benchmark circuits show that the proposed method could reduce, on the average, test data volume by 77% compared with the conventional multiple scan design. The scan tree construction enlarges the number of scan outputs required. However test data volume could be reduced by 66% even if the number of scan outputs is limited.

During last decade, IEEE standard 1687 or IJTAG has been utilized to test the embedded instruments on chips that support test and measurement applications. Recently, IJTAG has been incorporated into the newly developed testing architecture referred as a Streaming Scan Network (SSN) for efficient testing of the complex System-on-Chips (SoCs). IJTAG registers are used to configure the components of a Streaming Scan Host (SSH) node associated with each core in the SSN network. SSN supports packetized test data distribution for streaming of the test data through SSN bus. SSN provides efficient SoC testing by several times reduction in test time and test data volume with limited pin count. Although SSN outshines in providing testing benefits, it lacks security support. An unauthorized user can maliciously modify the configuration registers and extracts sensitive information. Presence of untrusted modules in the network also amplifies the security concerns as each packet may contain test data of multiple cores. Hence, an untrusted cores can simply sniff the data destined for other cores. Therefore, to address the security issues in SSN test architecture, one needs to protect the system against internal untrusted third-party intellectual property (3PIP) modules and unauthorized users. This work discusses the security vulnerabilities of SSN architecture by demonstrating an attack scenario. Keeping the flexibility of SSN intact, we propose a modified SSH architecture and an authorization unit to ensure security against data sniffing attacks and unauthorized accesses, respectively. A state-of-the-art scheme is compared against the proposed approach in terms of area overheads. Thus, this paper presents a multi-level methodology with very low area and testing overheads for secure SSN.

Combinational circuits implemented with exclusive-or gates are used for on-chip generation of deterministic test patterns from compressed seeds. Unlike major test compression techniques, this technique doesn't require test pattern generation with don't cares. Experimental results on industrial designs demonstrate that this new XPAND technique achieves exponential reduction in test data volume and test time compared to traditional scan and significantly outperforms existing test compression tools. The XPAND technique is currently being used by several industrial designs.

In this paper, we present a selective scan slice encoding technique for power-aware test data compression. The proposed scheme dramatically reduces test data volume via scan slice repetition, and generates an adjacent-filled test pattern known as the favorable low-power pattern mapping method. Experiments were performed on the large ITC'99 benchmark circuits, and results show the effectiveness of the proposed method.

Integrated circuit (IC) chip designs relying on Random Access Scan (RAS) architecture for post-production structural tests typically provide lower test power dissipation, test data volume, and test application time comparedto the classical serial scan-based Design for Test (DFT) methodology. However, previous RAS schemes incur high signal routing and test area overheads relative to the serial scan way. Unlike serial scan schemes, previous RAS schemes have not been effectively combined with test compression to further reduce test application time and test data volume. Authors have already formally documented a locally addressed (segmented) and compressed Segmented RAS (SRAS) architecture with low area overhead and test application time. This paper describes the SRAS architecture in more detail and provides comparative experimental results. Area overhead is reduced using test access hierarchy (segmented), while adding compression to RAS lowers the test application time.

A novel concurrent core test approach is proposed to reduce the test cost of SoC. Before test, a novel test set sharing strategy is proposed to obtain a minimum size of merged test set by merging the test sets corresponding to cores under test (CUT).Moreover, it can be used in conjunction with general compression/decompression techniques to further reduce test data volume (TDV). During test, the proposed vector separating device which is composed of a set of simple combinational logical circuit (CLC) is designed for separating the vector from the merged test set to the correspondent test core. This approach does not add any test vector for each core and can test synchronously to reduce test application time (TAT). Experimental results for ISCAS’ 89 benchmarks have been rproven the efficiency of the proposed approach.

In this paper, a novel compression/decompression test approach for system-on-a-chip (SoC) test using an embedded FPGA core is presented. The approach, employing Huffman coding, achieves test data volume and test application time reduction. The approach makes effective use of the embedded FPGA core such that the implementation is more efficient than that of the embedded processor-based approach. Due to the reconfigurable capability of FPGAs, the implementation of this approach has zero hardware overhead and higher flexibility in comparison with the general hardware-based implementation. Since the application with the FPGA has common problems of low speed and high power consumption, we demonstrate how to apply a CAM-based (content-addressable-memory) decompression architecture and low-power scan test vectors to overcome the difficulties. It is proven that the proposed approach is efficient from the experimental results.