Reusable context pipelining for low power coarse-grained reconfigurable architecture

Most of the coarse-grained reconfigurable architectures (CGRAs) are composed of reconfigurable ALU arrays and configuration cache (or context memory) to achieve high performance and flexibility. Specially, configuration cache is the main component in CGRA that provides distinct feature for dynamic reconfiguration in every cycle. However, frequent memory-read operations for dynamic reconfiguration cause much power consumption. Thus, reducing power in configuration cache has become critical for CGRA to be more competitive and reliable for its use in embedded systems. In this paper, we propose dynamically compressible context architecture for power saving in configuration cache. This power-efficient design of context architecture works without degrading the performance and flexibility of CGRA. Experimental results show that the proposed approach saves up to 39.72% power in configuration cache with negligible area overhead (2.16%).

This paper presents a method to time share the Processing Elements (PEs) of Runtime Coarse Grain Reconfigurable Architectures (CGRA) among multiple processes being executed concurrently onto the same CGRA. Runtime CGRA architectures time-multiplex the data path, creating a set of contexts for each state. These contexts configure the PEs and the routing resources of the CGRA and are typically loaded every clock cycle. The target architecture in this work is a commercial CGRA IP which is embedded as an IP into complex SoCs. Our proposed method analyzes the PE utilization in each context for multi-process systems running concurrently onto the same CGRA and time shares unused PEs assigned to one process with the other processes running in parallel. Our method reduces the total PE usage and hence the size of the CGRA IP and therefore the cost of the SoC. Results show that our method is extremely efficient and can reduce the PE utilization by up to 20% and on average by 14% and is only 2% worse than the optimal solution, while being much faster.

Coarse Grained Reconfigurable Architectures (CGRAs) are emerging as enabling platforms to meet the high performance demanded by modern applications. Commonly, CGRAs are composed of a computation layer (that performs computations) and a memory layer (that provides data and config ware to the computation layer). Tempted by higher platform utilization and reliability, recently proposed CGRA soffer dynamic application remapping (for the computation layer). Distributed scratch pad (compiler programmed) memories offer high data rates, predictability and low the power consumption (compared to caches). Therefore, the distributed scratchpad memories are emerging as preferred implementation alternative for the memory layer in recent CGRAs. However, the scratchpad memories are programmed at compile time, and do not support dynamic application remapping. The existing solutions that allow dynamic application remapping either rely on fat binaries (that significantly enhance configuration memory requirements) or consider a centralized memory. To extract the benefits of both runtime remapping and distributed scratchpad memories, we present a design framework called DyMeP. DyMeP relies on late binding and provides the architectural support to dynamically remap data in CGRAs. Compared to the state of the art, the proposed technique reduces the configuration memory requirements (needed by fat binary solutions) and supports distributed shared scratchpad memory. Synthesis/Simulation results reveal that DyMeP promises a significant (up to 60%) reduction in config ware size at the cost of negligible additional overheads (less then 1%).

Coarse-grained reconfigurable architecture (CGRA) is a promising accelerator design choice due to its high performance and power efficiency in the computation or data-intensive application domains, such as security, multimedia, digital signal processing, machine learning, and high-performance computing. CGRA consists of coarse-grained processing elements (PEs) and interconnects that determine the architecture flexibility to support different applications and also affect the performance and power efficiency significantly. Although multiple types of interconnects have been proposed, a parameterized unified model is still lacking. In this paper, we propose a flexible and scalable CGRA template with a novel interconnect model that can unify the typical neighbor-to-neighbor, switch-based, and FPGA-like interconnects. Furthermore, we present TRAM, an open-source template-based reconfigurable architecture modeling framework that integrates the Chisel-based CGRA modeling, architecture intermediate representation (IR) and Verilog generation, dataflow graph (DFG) mapping, simulation, and evaluation. The mapping flow contains graph-based placement and routing, critical-path-driven data synchronization, and simulated-annealing-based optimization. We evaluate the impacts of the rich design parameters, which demonstrate the significance of such a flexible template to facilitate architecture optimization. Compared with the related work, TRAM can achieve a 4.1× smaller DFG latency and a faster mapping speed for both the 8×8 and 16×16 CGRAs. Moreover, TRAM is able to attain an extremely high PE utilization of 94.4 % on average by architecture tuning.

Coarse Grained Reconfigurable Architectures (CGRAs) are emerging as enabling platforms to meet the high performance demanded by modern applications (e.g. 4G, CDMA, etc.). Recently proposed CGRAs offer runtime parallelism to reduce energy consumption (by lowering voltage/frequency). To implement the runtime parallelism, CGRAs commonly store multiple compile-time generated implementations of an application (with different degree of parallelism) and select the optimal version at runtime. However, the compile-time binding incurs excessive configuration memory overheads and/or is unable to parallelize an application even when sufficient resources are available. As a solution to this problem, we propose Transformation based dynamic Parallelism (TransPar). TransPar stores only a single implementation and applies a series for transformations to generate the bitstream for the parallel version. In addition, it also allows to displace and/or rotate an application to parallelize in resource constrained scenarios. By storing only a single implementation, TransPar offers significant reductions in configuration memory requirements (up to 73% for the tested applications), compared to state of the art compaction techniques. Simulation and synthesis results, using real applications, reveal that the additional flexibility allows up to 33% energy reduction compared to static memory based parallelism techniques. Gate level analysis reveals that TransPar incurs negligible silicon (0.2% of the platform) and timing (6 additional cycles per application) penalty.

Coarse-grained reconfigurable architectures aim to achieve goals of both high performance and flexibility. However, existing reconfigurable array architectures require many resources without considering the specific application domain. Functional resources that take long latency and/or large area can be pipelined and/or shared among the processing elements. Therefore, the hardware cost and the delay can be effectively reduced without any performance degradation for some application domains. We suggest such a reconfigurable array architecture template and a design space exploration flow for domain-specific optimization. Experimental results show that our approach is much more efficient, in both performance and area, compared to existing reconfigurable architectures.

Coarse-grained reconfigurable architectures (CGRAs) are increasingly employed as domain-specific accelerators due to their efficiency and flexibility. A CGRA typically relies on compilers to perform task scheduling. The longstanding problem of static scheduling is that it suffers from insufficient parallelism in handling irregularities due to over-serialization and workload imbalance, which leads to severe resource underutilization and performance loss. To counteract the limitations of static scheduling in CGRAs, it is essential to exploit dynamic parallelism automatically and manage hardware resources adaptively. However, existing dynamic scheduling mechanisms, e.g., work stealing, often reschedule aggressively for instant performance but sacrifice efficiency, which is unfavorable to CGRAs that emphasize efficiency and fewer reconfigurations. This article proposes an elastic task scheduling scheme that enables lightweight dynamic scheduling in CGRAs. Tasks are rescheduled at runtime according to the classic tagged-token dataflow paradigm to enable dynamic task-level parallelism. Meanwhile, tasks are dynamically resized according to run-time throughputs via duplication, combination, and substitution operators for balanced multitask execution. We implement the elastic task scheduling scheme on a well-known reconfigurable architecture - triggered instruction architecture (TIA). Evaluation on the MachSuite benchmarks shows that the proposed scheme is effective in improving performance and energy efficiency. The average speedup is 2× over the baseline. Also, our design attains a 57 percent improvement in the area-normalized performance and a 49 percent better energy efficiency. Compared with a state-of-the-art dynamic scheduling method, our scheme achieves 1.6× speedup and 1.6× energy efficiency than work-stealing mechanism on the same substrate.

As computation migrates to the edge, energy efficiency is becoming even more critical in the design of electronic devices. Therefore, new applications for the Internet of Things pose a challenge for designers to find the optimal balance between performance and energy consumption. While Coarse Grained Reconfigurable Architectures (CGRA) have been an alternative to provide the required acceleration, they are far from being the most energy-efficient, since their functional units may be underutilized by some applications. In this work, we introduce a novel approach to handle these CGRA resources, which leverages the variable usage of functional units due to the application program phases. By using our new approach and performing power-gating of under-utilized parts of the CGRA, we demonstrate that it is possible to achieve reductions of up to 52.3% in power dissipation and 75% in energy consumption.

One of the grand challenges in the design of portable/wearable electronics is to achieve optimal efficiency and flexibility in a tiny low power package. Coarse grained reconfigurable architectures (CGRAs) hold great promise for low power, high performance, and flexible designs for a domain of applications. CGRAs are very promising due to the ability to highly customize such architectures to an application domain. However, greater customization makes the mapping of applications onto these architectures very challenging. Good tools and fast, effective mapping algorithms are needed to support design space exploration for CGRAs. In particular, the mapping problem has been difficult to solve in a satisfying and general way. In this paper, we present an architectural design flow using crowdsourcing to provide mappings of benchmarks onto new architectures. We show that the crowd can provide high quality, reliable mappings, significantly outperforming our custom Simulated Annealing algorithm in almost all cases. We further show that the crowd can provide other types of feedback that are difficult to obtain from an automatic mapping algorithm. Our proof of concept cross-architectural study supports an 8Way or 4Way1Hop architecture as a top choice, concludes that a custom modification that constrains inputs and outputs consumes less energy but requires more area than its less constrained counterpart, and suggests that Stripe architectures are interesting to consider because they perform nearly as well as our mesh variants and may present a more straightforward mapping problem for the crowd or an automatic mapping algorithm.

In this paper, a general visualization tool for coarse-grained reconfigurable architecture (CGRA) modeling is introduced. Recently, the increasing requirement for efficient and flexible architectures has significantly boosted the interests in CGRA. However, not too much attention has been paid to visualization tools for the development of CGRAs. This paper contains two main parts of contribution. Firstly, the CGRAs are built with a high level modeling language called FDL. Secondly, a user interface which could present all the information in the FDL model is obtained. Furthermore, the generated configuration bit stream helps to build routing paths on the interface.

Coarse-grained reconfigurable array architectures have drawn increasing attention due to their performance and flexibility. A typical coarse-grained reconfigurable array architecture has many PEs in the array, which is suitable for implementing spatial redundancy used for fault-tolerant systems design. In this paper, we propose to implement replications and a voting function on the PE array of a coarse-grained reconfigurable array architecture to design a fault-tolerant system. We also introduce thermal-aware application mapping onto the coarse-grained reconfigurable array architecture for reliability. The experiment with Viterbi decoder shows that our approach enables implementing fault-tolerance with 12% area overhead which comes from implementing conditional execution.

It is very important to design a good routing-system for the whole compile-synthesis system of reconfigurable architecture (RA). Because the routing resources of coarse-grain RA (CGRA) are less than those of fine-grain RA, and several functions are often defined in same one element of RA, it is difficult to find a good route. Therefore, it is more important for routing-algorithm of CGRA to have stronger ability of finding feasible and optimum path. In the paper, the improved max—min Ant System (MMAS) that added the ability of smell for ant is applied for the routing problem of CGRA. By several benchmarks on CTaiJi that is a new developed CGRA, The improved MMAS shows better ability to find the best solution than PathFinder that is often used now.KeywordsConnected GraphField Programmable Gate ArrayOptimum PathPheromone TrailRout ProblemThese keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Emerging communication technologies, such as 5G and beyond, have introduced diverse requirements that demand high performance and energy efficiency at all levels. Furthermore, the real-time requirements of different services vary significantly — increasing the baseband processor design complexity and demand for flexible hardware platforms. This paper identifies the key characteristics of hardware platforms for baseband processing and describes the existing processing limitations in traditional architectures. In this paper, Coarse-Grained Reconfigurable Architecture (CGRA) is examined as a prospective hardware platform and its characteristic features are highlighted as compared to traditionally employed architectures that make it a suitable candidate for incorporation as a domain-specific accelerator in baseband processing applications. We survey various CGRAs from the last two decades (2004-2023) and analyze their distinct architectural features which can serve as a reference while designing CGRAs for baseband processing applications. Moreover, we investigate the existing challenges toward developing CGRAs for baseband processing and explore their potential solutions. We also provide an overview of the emerging research directions for CGRA and how they can contribute toward the development of advanced baseband processors. Lastly, we highlight a conceptual RISC-V+CGRA framework that can serve as a potential direction toward integrating CGRA in future baseband processing systems.

Designing coarse-grain reconfigurable architectures by inlining flexibility into custom arithmetic data-paths

This paper presents a novel architecture design to optimize the reconfiguration process of a coarse-grained reconfigurable architecture (CGRA) called Reconfigurable Multimedia System II (REMUS-II). In REMUS-II, the tasks in multi-media applications are divided into two parts: computing-intensive tasks and control-intensive tasks. Two Reconfigurable Processor Units (RPUs) for accelerating computing-intensive tasks and a Micro-Processor Unit (µPU) for accelerating control-intensive tasks are contained in REMUS-II. As a large-scale CGRA, REMUS-II can provide satisfying solutions in terms of both efficiency and flexibility. This feature makes REMUS-II well-suited for video processing, where higher flexibility requirements are posed and a lot of computation tasks are involved. To meet the high requirement of the dynamic reconfiguration performance for multimedia applications, the reconfiguration architecture of REMUS-II should be well designed. To optimize the reconfiguration architecture of REMUS-II, a hierarchical configuration storage structure and a 3-stage reconfiguration processing structure are proposed. Furthermore, several optimization methods for configuration reusing are also introduced, to further improve the performance of reconfiguration process. The optimization methods include two aspects: the multi-target reconfiguration method and the configuration caching strategies. Experimental results showed that, with the reconfiguration architecture proposed, the performance of reconfiguration process will be improved by 4 times. Based on RTL simulation, REMUS-II can support the 1080p@32fps of H.264 HiP@Level4 and 1080p@40fps High-level MPEG-2 stream decoding at the clock frequency of 200MHz. The proposed REMUS-II system has been implemented on a TSMC 65nm process. The die size is 23.7mm2 and the estimated on-chip dynamic power is 620mW.