Synchronisation algorithm based on zero correlation code pair for OFDM‐based VLC systems

In visible light communication (VLC) system, the Orthogonal Frequency Division Multiplexing (OFDM) technique has been widely used to achieve a high data rate transmission. However, OFDM will cause high peak-to-average power ratio (PAPR) in the VLC system. In this paper, we propose and experimentally demonstrate a new interleaved Discrete Fourier Transform Spread Orthogonal Frequency Division Multiplexing (DFT-S OFDM) method. We compare the interleaved DFT-S technique to other PAPR reduction techniques, such as Clipping OFDM and conventional DFT-S. The experimental results show that interleaved DFT-S achieve FEC threshold for an overall 2.0Gb/s 32QAM signal over the 1.05m transmission. In addition, interleaved DFT-S presents significant PAPR reduction, low complexity and optimal BER performance, when compared to other techniques.

Orthogonal frequency-division multiplexing (OFDM) has been widely studied and adopted in visible-light communication (VLC) systems because of its high spectral efficiency and low-complexity implementation. However, OFDM-based VLC systems suffer from a high peak-to-average power ratio (PAPR), along with the nonlinear transfer characteristics of light-emitting diodes (LEDs). In this paper, a subcarrier grouping scheme for an OFDM-based VLC system is proposed. This scheme exploits the property that one LED lamp usually contains multiple independent LED chips. In the proposed scheme, all OFDM signal subcarriers are divided into groups, and each group is transmitted by an individual LED chip while the same receiver structure is maintained. The PAPR is reduced significantly because only some of the subcarriers are located on each LED chip. Hence, the achievable input power can be increased, leading to a higher signal-to-noise ratio (SNR) and a lower bit error rate (BER). Simulated and experimental results demonstrate that the BER performance can be improved by over two orders of magnitude. Moreover, an adaptive switching mechanism is also proposed in this paper, in which a subcarrier grouping scheme is employed adaptively when the required input power is high. Simulation results validate that the proposed mechanism can enhance system robustness significantly.

Visible light communication (VLC) is a technology that is currently being employed to achieve high data rates. Orthogonal frequency division multiplexing (OFDM) is a powerful scheme for intensity modulation and direct detection (IM-DD) that is becoming increasingly important. OFDM systems based on VLC are accomplished through the implementation of IM-DD constraints, including direct current biased optical OFDM (DCO-OFDM), asymmetrically clipped optical OFDM (ACO-OFDM), and asymmetrically clipped DC-biased (ADO-OFDM), among others. The OFDM technique based on VLC is inefficient in terms of spectral efficiency and has a high peak to average power ratio (PAPR). In this article, the symbol time compression-image adjust (STC-IMADJS) technique will be proposed for throughput maximization and PAPR reduction in the DCO-OFDM, ACO-OFDM, and ADO-OFDM systems. Furthermore, the STC technique enables the simultaneous transmission of two sub-carriers through Walsh spreading codes without inference between them. As a result, the OFDM symbol has been reduced by 50%. The IMADJS strategy reduces the high PAPR of transmitted signals by compressing large signals and expanding small signals, as long as the average power level remains constant after compression. Therefore, the proposed STC-IMADJS technique doubles the throughput as well as significantly reduces the PAPR for OFDM systems based on VLC. The simulation results are performed using Matlab-2021a for 1024 sub-carriers. As a result, the simulation results show that the proposed technique reduces the PAPR by 3.7 dB (86%), 8.16 dB (93%), and 1.81 dB (20%) for DCO-OFDM, ACO-OFDM, and ADO-OFDM systems respectively. Furthermore, the technique has a significantly lower computational complexity than conventional OFDM systems based on VLC. Finally, the measures of performance through this article are bit error rate and complementary cumulative distribution function.

The exponential rise in wireless communication demands and allied applications have revitalized academia-industries to develop an efficient and potential solution. Furthermore, the high-pace increasing scarcity of radio spectrum has also alarmed researchers to achieve better Quality of Service (QoS) centric solution. To meet such demands Visible Light Communication (VLC) systems have gained global attention; however, up surging high rate, range and reliability (3R) needs demand better performance. Towards these goals, Multiple Input Multiple Output (MIMO) based VLC systems is an efficient approach; though its efficacy under Multiple Users (MU) conditions remains least explored. Enabling MIMO-MU based VLC can achieve 3R objectives effectively; however, factors like multipath attenuation, interferences and varied impairment-affects makes classical approached confined. The MIMO-MU VLC systems require robust error, noise or interference resilient transmission even under adverse conditions such as non-linear LED, multipath attenuation and interference. Towards these objectives, in this paper a highly robust MIMO-MU VLC system is developed that incorporates an augmented MIMO channel design and combined pre-coding and post equalization schemes. To alleviate major interference probability in MIMO-MU environment, proposed model incorporates time (delay)-multiplexing based data transmission followed by signal adaptive precoding and Volterra Kernel based Hybrid-equalizer. This approach enables interference and noise removal as well as LED non-linearity handling under MIMO-MU VLC communication. The use of a Volterra Kernel based Decision Feedback Equalization with both linear as well as non-linear equalization enables proposed VLC system to exhibit low Bit Error Rate with low modulation index and taps, that optimizes trade-off between performance as well as complexity.

• Core Innovation & Objective • Developed a novel, integrated system architecture combining a modified USRP X310 software-defined radio platform with a custom-designed high-power LED optical transceiver. • Achieved high-speed, low-latency, and highly reliable audio-video transmission over Visible Light Communication (VLC) for intelligent transportation and vehicle-to-vehicle (V2V) applications, particularly in electromagnetically sensitive environments. • Key Technical Breakthroughs • LED Bandwidth Extension: Designed an innovative active pre-equalization circuit (based on a 4th-order high-pass RC bypass and op-amps) that dramatically increased the 3dB modulation bandwidth of a commercial 15W LED from 3 MHz to 120 MHz. • High-Speed Modulation: Successfully implemented 64QAM-OFDM modulation/demodulation using GNU Radio on the USRP, enabling spectrally efficient data transmission. • Advanced Optical Design: Custom-designed optical lenses (transmitter and receiver) and a high-power Bias-T circuit for efficient AC/DC coupling, ensuring the LED operates in its linear region and maximizing optical power transfer. • Stable Link Performance: Incorporated an Automatic Gain Control (AGC) circuit at the receiver, stabilizing the output voltage between 1.2V - 2.0V and maintaining a modulation signal-to-noise ratio (SNR) > 23 dB over varying distances. • Outstanding System Performance • The experimentally demonstrated performance metrics are exceptional for a VLC system: • Peak Data Rate: 500 Mbps • Communication Distance: 0 - 110 meters • Bit Error Rate (BER): As low as 1.74 × 10⁻⁵ (far below the 1 × 10⁻⁴ target) • End-to-End Latency: < 0.1 s • Beam Angle: 11.5° (Transmitter) • Field of View (FOV): ≤ 18° (Receiver) • System Integration and Design • Hardware-Software Co-Design: Seamless integration of the USRP X310 (handling digital baseband processing) with the custom analog optical front-end. • Compact and Practical: The system is designed for external mounting on vehicles, offering a practical solution for real-world deployment. • Simulation-Guided Design: Used LightTools for optical design and Optisystem for communication link simulation to validate the design before implementation. • Significance and Application Value • Solves Critical Challenges: Provides a high-speed, secure, and EMI-free communication alternative to traditional RF in environments like military operations, petroleum facilities, and intelligent transportation systems. • 6G Potential: Serves as a practical reference for the development of VLC as a complementary technology in 6G networks. • Demonstrates Feasibility: Successfully proves the viability of using commercial LEDs and USRP platforms for building high-performance, medium-to-long-range optical communication systems. • This work represents a significant step forward in practical high-speed VLC system design, combining theoretical innovation with robust engineering to achieve state-of-the-art performance. Existing vehicular VLC systems suffer from limited bandwidth, short transmission distances, low data rates, and support only a narrow range of communication services. To address these issues, this paper proposes a vehicle-mounted high-speed LED visible light communication (VLC) system based on Universal Software Radio Peripheral (USRP). Leveraging 64QAM-OFDM digital modulation, an improved USRP X310 hardware platform, and a PC, we establish a novel architecture comprising digital baseband and optical transceiver modules. The baseband module eliminates traditional spectrum-shifting circuits and antennas, retaining only FPGA and ADC/DAC units. Audio/video files undergo 64QAM-OFDM modulation directly on the PC, with modulated signals output via DAC to a custom-designed wide-bandwidth LED transceiver. A broadband hardware equalization network based on a fourth-order RC bypass circuit was designed expands the 3dB bandwidth of high-power LEDs from 3 MHz to 120 MHz. Combined with automatic gain control (AGC), this achieves an optical transceiver with 12–15 W output power, >23 dB optical modulation signal-to-noise ratio (SNR), and stable receiver output voltage (1.2–2.0 V). The resulting compact system delivers low latency, high data rates, and high reliability. Under aligned optical path conditions, the system achieves >1 Mbit/s at 110 m (BER 0.49 × 10⁻⁵, delay 0.009-0.05s) and a peak rate of 500 Mbit/s at 10 m (BER 7.4 × 10⁻⁵), with an 11.5° transmit angle and a receiver field of view (FOV) of less than 18°. This work demonstrates the feasibility of high-power LED-based 64QAM-OFDM communication using USRP X310 for medium- to long-range vehicular links, providing a reference for intelligent transportation systems.

This paper proposes an asymmetric frequency shift keying (AFSK) modulation technique for visible light communications (VLC) systems. AFSK is derived from the normal FSK in response to the non-negative aspect of VLC technology. AFSK provides VLC systems with a low cost and low complexity modulation technique that mitigates flickering and dimming for both square and rectified sine waves signals. The binary version of AFSK is analyzed and a general expression is proposed to its carrier frequency based on the original FSK. Simulated results of selected AFSK constellation sizes which perform better than on-off keying are presented. We also present M-ary FSK (MFSK) modulation in the VLC channel.

In this letter, an improved linear nonsymmetrical transform (ILNST) is proposed to reduce the peak-to-average power ratio (PAPR) for asymmetric clipping optical orthogonal frequency division multiplexing-based visible light communication (VLC) systems. The emission power conservation criteria are implemented to calculate the enlarge coefficient with a given compression coefficient. The transfer characteristic of a 5 mm commercial light-emitting diodes is introduced to estimate the VLC systems performance. Bit error ratio (BER) and complementary cumulative distribution function simulation results show that the proposed ILNST outperforms the classical linear nonsymmetrical transform method in PAPR reduction and BER enhancement.

Multiple-input multiple-output (MIMO) technique is now used in most new broadband communication system, and orthogonal frequency division multiplexing (OFDM) is also utilized within current 4^th generation (4G) of mobile telecommunication technology. With MIMO and OFDM combined, visible light communication (VLC) system’s diversity gain is increase, yet system capacity for dispersive channels is also enhanced. Moreover, with the emerging massive MIMO-OFDM VLC system, there are significant advantages than smaller systems’ such as channel hardening, further increasing of energy efficiency (EE) and spectral efficiency (SE) based on law of large number. This paper addresses one of the major technological challenges, system architecture design, which was solved by semispherical beehive structure (SBS) receiver and so that diversity gain can be identified and applied in Massive MIMO VLC system. Simulation results shows that the proposed design clearly presents a spatial diversity over conventional VLC systems.

Encrypted image transmission in OFDM-based VLC systems using symbol scrambling and chaotic DFT precoding

While the traditional Visible Light Communication (VLC) system has attracted a lot of research attentions on boosting throughput, using Commercial Off-The-Shelf (COTS) devices, e.g. existing cameras on the smartphones, is a recent trend to implement readily deployable VLC systems. In particular, since LED-Camera VLC systems have shown a promising potential in large indoor communication due to the growing deployment of LED lighting infrastructure, a comprehensive VLC system with cooperative transmission and roaming support has become an impending need. To this end, we propose a novel VLC and visible light sensing (VLS) system to address that by leveraging LED sensing and effective encoding/decoding schemes. It is achieved first by utilizing LED sensing via converting parts of LED luminaire into light sensors to detect diffuse reflection change caused by presence of the user. After the users are detected and located, the system employs rateless codes and newly designed code assignment scheme to collaboratively transmit to detected users in their communication cells. We believe the proposed system has the potential to a roaming support VLC system in the whole building or indoor areas.

SummaryWith the development of new generation lighting sources, visible light communication (VLC) system has become a complementary solution to traditional radio frequency wireless system. However, the error performance of VLC system is degraded because of multipath effects and interference from other lighting sources that, in turn, reduce the communication range. This work targets the issue of performance degradation of VLC systems in terms of communication range and demonstrates a VLC system design that utilizes forward error correction (FEC) codes as the main tool to fix this issue. Furthermore, the work also covers practical implementation of the proposed VLC system using UART modules programmed in MATLAB. The hardware results demonstrate that the communication range of the proposed VLC system is enhanced up to 0.5 m. Over and above, it is also shown through simulations that the coding gain of the proposed design is more when compared with existing VLC system(s).

Smart city planners pay more attention towards visible light communication (VLC) system to achieve seamless high speed connectivity. A light emitting diode (LED) acts as a transmitter in VLC system. However, the nonlinear characteristics and dimming nature of LED limits the performance of the VLC system by degrading the quality of transmitted signal. In this paper, we propose an adaptive-learning-architecture (ALA) based predistortion technique to estimate and compensate for LED nonlinearities as well as increase the spectral efficiency of a VLC system. A DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM) signal is considered. The performance with and without predistorter is analysed assuming optical line-of-sight (LOS) channel. It is shown that degradation due to LED nonlinearity can be compensated by using ALA-based predistortion, and the overall Predistorter-LED system is able to approach near-linear performance. Further, we investigate the impact of dimming on the performance of nonlinear LED in VLC system. Simulation results based on symbol error rate (SER), amplitude distortion (AM/AM) curves and constellation plots validate the performance of our proposed technique.

Recently, multiple-input multiple-output (MIMO) has been proposed in visible light communications (VLC) systems to boost the data rate by utilizing spatial multiplexing. Unlike RF systems in VLC, lighting requirements, such as dimming control, should be taken into consideration for the design of a VLC transceiver. Moreover, VLC systems are inherently nonlinear and dynamic-range-limited. To drive an LED transmitter, the signal is bounded by a turn-on value and a saturation value. In this letter, we show how the dynamic-range constraint and dimming control impact the design of MIMO transceiver. Three different MIMO schemes are proposed and studied by theoretical analysis and simulation.

Power control technology is necessary in Visible Light Communication (VLC) systems because of the multipath distortion and shadowing. When a power control algorithm is applied to the system, feedback error is inevitable. In this paper, we analyze the closed-loop power control algorithm and the influence of the power control error (PCE) in VLC systems. To analyze the effect of the PCE in VLC systems, the proposed system is studied with different modulation schemes and coding rates in terms of BER.

The enhanced proliferation of connected entities needs a deployment of innovative technologies for the next generation wireless networks. One of the critical concerns, however, is the spectrum scarcity, due to the unprecedented broadcast penetration rate nowadays. Based on this, visible light communication (VLC) has recently emerged as a viable solution to secure high-speed communications. VLC, a high data rate communication technology, has proven its stature as a promising complementary to its radio frequency (RF) counterpart. VLC is a cost-effective, energy-efficient, and secure technology that exploits the current infrastructure, specifically within indoor and underwater environments. Yet, despite their appealing capabilities, VLC systems face several limitations which constraint their potentials such as LED’s limited bandwidth, dimming, flickering, line-of-sight (LOS) requirement, impact of harsh weather conditions, noise, interference, shadowing, transceiver alignment, signal decoding complexity, and mobility issue. Consequently, non-orthogonal multiple access (NOMA) has been considered an effective technique to circumvent these shortcomings. The NOMA scheme has emerged as a revolutionary paradigm to address the shortcomings of VLC systems. The potentials of NOMA are to increase the number of users, system’s capacity, massive connectivity, and enhance the spectrum and energy efficiency in future communication scenarios. Motivated by this, the presented study offers an overview of NOMA-based VLC systems. This article provides a broad scope of existing research activities of NOMA-based VLC systems. This article aims to provide firsthand knowledge of the prominence of NOMA and VLC and surveys several NOMA-enabled VLC systems. We briefly highlight the potential and capabilities of NOMA-based VLC systems. In addition, we outline the integration of such systems with several emerging technologies such as intelligent reflecting surfaces (IRS), orthogonal frequency division multiplexing (OFDM), multiple-input and multiple-output (MIMO) and unmanned aerial vehicles (UAVs). Furthermore, we focus on NOMA-based hybrid RF/VLC networks and discuss the role of machine learning (ML) tools and physical layer security (PLS) in this domain. In addition, this study also highlights diverse and significant technical hindrances prevailing in NOMA-based VLC systems. We highlight future research directions, along with provided insights that are envisioned to be helpful towards the effective practical deployment of such systems. In a nutshell, this review highlights the existing and ongoing research activities for NOMA-based VLC systems, which will provide sufficient guidelines for research communities working in this domain and it will pave the way for successful deployment of these systems.