A Method of Locating Open Faults on Incompletely Identified Pass/Fail Information

To produce high-quality and cost-effective multichip systems, they must be designed with test and fault diagnosis as critical design requirements. However, deciding on where and when to test, and whether to apply design for test (DFT) and built-in self test (BIST) at the IC, multichip module (MCM) or board level requires considerable study and evaluation to determine the economics of the various solutions and the payback. In this paper we explore the tradeoffs between various test and rework strategies for multichip module designs. Some of these strategies incorporate various DFT options at both the MCM and IC levels. We will analyze the impact of various cost, yield, and test effectiveness parameters on the final cost and quality of multichip modules. Experimental tradeoff analysis data generated for some leading-edge multichip designs will also be presented. The results clearly indicate that incorporating DFT and BIST with varying degrees at the chip or MCM levels is economically justifiable and results in cost reduction as well as quality improvement. The results also indicates that the MCM cost could vary by about 10–20% depending on the test strategy used. However, proper determination of where and how to test, and whether to employ DFT and BIST at the IC or MCM levels, requires an evaluation of the economics of the various solutions and the payback. That process is highly dependent on the design under consideration and the parameters associated with the available manufacturing environment(s). Hence, one has to be careful about generalizing the lessons learned from specific cases, since it could lead to non optimal solutions. A careful economic modeling of the various design, test and manufacturing parameters is clearly necessary for producing cost-effective high-quality products.

A new technique called input reduction is proposed for built-in self test (BIST) test pattern generator (TPG) design and test set compaction. This technique analyzes the circuit function and identifies sets of compatible and inversely compatible inputs; inputs in each set can be combined into a test signal in the test mode without sacrificing fault coverage, even if they belong to the same circuit cone. The test signals are used to design BIST TPGs that guarantee the detection of all detectable stuck-at faults in practical test lengths. A deterministic test set generated for the reduced circuit obtained by combining inputs into test signals is usually more compact than that generated for the original circuit. Experimental results show that BIST TPGs based on input reduction achieve complete stuck-at fault coverage in practical test lengths (/spl les/2/sup 30/) for many benchmark circuits. These are achieved with low area overhead and performance penalty to the circuit under test. Results also show that the memory storage and test application time for external testing using deterministic test sets can be reduced by as much as 85%.

Numerous Built-In Self Testing (BIST) designs now exist for the testing of Programmable Logic Arrays (PLA), but their practical usefulness has not been studied. In this paper, we implement and compare several BIST designs using a common methodology of implementation. We also perform an yield analysis to characterize the yield degradation due to the BIST design methodology. Our preliminary findings of this work is that BIST approach results in considerable degradation of yield, and therefore may not be suitable as a test vehicle for PLAs.

In this research, a BIST (built in self test) architecture for testing crosstalk effects in highly dense Through Silicon Via (TSV) placed in structured array form, in 3DICs (Three Dimensional integrated circuits), designed and simulated using the Xilinx ISE tool and the VHDL language. A novel methodology is proposed, and simulated, to observe the test responses of the victim TSVs in the chosen group simultaneously. Boundary-scan cell structures are modified, created for the purpose of operating in different modes such as shift, update and capture in either conventional serial shift mode as well as in proposed parallel broadcasting mode. Output Response Analyzers (ORA), or signature analyzers that have been simulation-verified. In this study, we suggested a novel encoder-based signature generator to locate faulty TSVs in the parallel-observed TSVs. This paper discusses the whole BIST architecture, the BIST controller built on an algorithmic state machine, the design of TPG (Test Pattern Generator), and the faulty TSV signature generator. Comparing the BIST architecture, to serial shift based interconnect tests done by IEEE 1149.1 (JTAG) such as EXTEST and IEEE 1838 standards, the test’s time complexity of BIST is relatively very low. The entire TSV array test is completed in just 32 clock cycles. The design is adaptable and can be used to broadcast test patterns to a group or to transmit test patterns serially using IEEE 1838 or 1149.1.

We present a testable built-in self test(BIST) design for phase-lock loop(PLL). The design can measure the clock jitter for PLL with high precision and high accuracy due to better utilization of the test integration and test subtraction techniques. Although the BIST circuit is implemented by all digital standard cells to achieve better reliability, it can even be applied to measure the analog clock jitter. Besides, for some DfT (design for test) techniques inserted to make BIST itself testable, we discuss the trade-off among area, timing, number of test patterns and fault coverage in this paper.

This paper deals with information model for power grid fault diagnosis based on Common Information Model (CIM). Fault diagnosis gains information from topology information and device parameters of primary system grid based on IEC61970 standard and device information of secondary system grid based on IEC 61850. Device information contains information of protection movement wave record and protection configuration. However, the existent CIM can't fully represent power system fault diagnosis information. Thus, it is need to extend CIM. All kinds of information are based on different model, which causes different information standard. In this paper a preliminary study on CIM extensions which is based on power system fault diagnosis, has been proposed to perfect fault information model. On the basis of different standard model, this paper has discussed the theory of coordinating IEC 61850 and IEC61970 standard, and proposed using Web Ontology Language (OWL) based on Extensible Mark-up Language (XML) to the solution of this problem. A fault Information Model is then provided to the fault diagnosis system according to Component Interface Specification (CIS) in IEC61970. After receiving fault information, the fault diagnosis system starts for real-time, on-line fault diagnosis. Fault information model has solved the problem of the deficiency and non-standard of fault diagnosis information, attaining fault diagnosis information integrity and standardization, and making the fault diagnosis result fast and accurate.

Linear dependency check in built-in test

We present a novel approach for built-in self test (BIST) for VLSI. Many conventional BIST schemes use signatures generated by a linear feedback shift register (LFSR) or a multiple input signature register (MISR) for determining whether the device under test is faulty or fault free. In the approach presented, fault detection is made based on the number of different states the LFSR visits. This number is called the cycle length. It is also shown that such an approach results in the probability of aliasing of 2/sup -(2m-1+m/), where m denotes the number of registers in the LFSR, compared to 2/sup -m/ achieved by conventional signature analyzers. We also present the complexity of the additional hardware required to implement the scheme.

HIERARCHICAL SELF TEST FOR SOCS INCLUDING LOGIC AND INTERCONNECTS

This paper represents an innovative solution to reduce phase noise present on the GMSK modulated spectrum in an all-digital RF transmitter employing a discrete-time oscillator. The root cause of this issue is the improper timing of oscillator tuning word update with respect to the digitally-controlled oscillator (DCO) capacitor state. Using the built-in self test (BIST) circuit in the all-digital PLL (ADPLL), the DCO tuning word update timing is calibrated such that the impact on the phase noise is compensated and desired modulated spectrum margin from the specification is achieved

In this paper, we present a new RF built-in self test (BIST) circuit for 865–870 MHz low noise amplifiers (LNAs); The BIST and LNA circuit is designed using 0.35µm CMOS technology. The simple circuit of test that contains a RF peak detectors and two comparators brings high fault coverage. The faults simulating possible catastrophic and parametric faults are introduced. A total of twenty eight short and open faults and ten parameters variation have been introduced into the LNA, giving fault coverage of 89% for catastrophic faults and 90% for process variation.

Built-In Self Test (BIST) has been proposed as a powerful technique for addressing the highly complex testing problems of VLSI circuits. In the BIST methodology, two major problems which must be addressed are test generation and response analysis. In this paper, we present an efficient unified procedure, named three-phase cluster partitioning, to automatically synthesize a pseudo-exhaustive test generator for VLSI BIST design. Previous approaches to the problem of test generation have optimized computational efficiency at the expense of the required hardware overhead, or vice versa. Our design procedure is computationally efficient and produces test generation circuitry with low hardware overhead. The procedure minimizes the number of test patterns that are required for pseudo-exhaustive test. Based on three-phase cluster partitioning, a design generator named BISTSYN has been developed and implemented to facilitate the BIST design. The input to the design generator is a circuit description at the gate level which is viewed as a netlist. BISTSYN provides the BIST mechanisms as the output. For those conventional circuits which are extremely unsuitable for pseudo-exhaustive test, BISTSYN employs a circuit partitioning tool, named Autonomous, to partition the combinational portion of the circuit into different structural subcircuits so that each subcircuit can be pseudo-exhaustively tested. We demonstrate the effectiveness of BISTSYN by applying the method to different examples and practical VLSI designs. The detailed comparisons of our benchmark simulation results against those that would be obtained by existing techniques are also presented. >

Time to market constraints pushes more and more designers to make area estimations early during the design process. Estimating the Built-In Self Test (BIST) area is only possible once the different design memories BIST are synthesized. This is time consuming and not realistic for a large circuit such as a SOC which can include hundreds of memories. In this paper we propose a push button solution for BIST area estimation called BARES based on Artificial Neuronal Networks handling. Experiments have been performed on different STMICROELECTRONICS BIST memories and results prove the efficiency of the proposed method.

This paper describe the importance of temperature sensor built-in self test (BIST) for microhotplate-based sensors. It shows possible ways to implement BIST functionality for microhotplate temperature sensors, including resistance temperature detectors (RTD), microhotplate thermal efficiency, and Thermocouples. A calibration technique is discussed and conclusions are given.

In modern nanotechnologies, the testing of embedded wireless transceivers' RF front-ends is a great concern. The test technique presented in this work is based on dedicated built-in self test (BIST) structures for each building block of the transceiver. These BIST circuits utilize defect-oriented test techniques. Experimental results on a CMOS transceiver design are discussed to accentuate the efficiency of the proposed scheme.