Dynamic power estimation for ROM-less DDFS designs using switching activity analysis

A ROM-less direct digital frequency synthesizer (DDFS) is implemented based on a new 8th-order polynomial approximation of a cosine function, where digital square circuits are used to realize the components of the polynomial. MATLAB tools are used to simulate the performance of the DDFS system, where the spurious free dynamic range (SFDR) is employed as the performance factor. For a DDFS with a superior quality, the higher the SFDR, the better the spectrum purity. To validate the performance of the DDFS, the Altera FPGA platform is used with Quartus II and ModelSim, where simulation results based on Verilog implementation are illustrated.

A novel design is presented about ROM-less direct digital frequency synthesizer (DDFS) using phase to sinusoid amplitude conversion blocks based on the two segment fourth-order parabolic approximation. The mathematical maximum error analysis shows that the resolution is up to 14 bits. In order to reduce the hardware complexity without sacrificing speed, the squarer and constant multipliers have been decomposed and optimized. The whole architecture has been split into twenty pipelining stages with a 200 MHz clock rate and a single phase output up to 50 MHz. Meanwhile, because the sine and cosine phase to amplitude modules share the same hardware, reduction of hardware complexity and power consumption can be achieved. Spectral purity analysis shows that the worst case spurious free dynamic range (SFDR) is about -90 dBc. The implementation demonstrates that the proposed DDFS architecture can be realized with a smaller hardware scale and lower power consumption than many other existing approaches.

A 4-stage pipeline ROM-less direct digital frequency synthesizer (DDFS) with equal division interpolation is proposed in this work. To attain higher SFDR (spurious free dynamic range) and faster clock rate, the hardware cost and delay using different segments with various interpolation equations are analyzed systematically to explore the optimal solution. The parabolic equations with proper selection of coefficients and factorized operation orders based on optimized hardware cost and delay are finally utilized to enhance SFDR. The proposed design is demonstrated by the physical implementation on Altera FPGA platform. The average SFDR is measured to be 68.4242 dBc with 1.1659 dBc deviation over 33 times of experiments. The measured SFDR is proved to outperform many previous DDFS works even if they were implemented on silicon.

By using a sine wave Digital-to-Analog Converter (DAC) to perform mapping from digital phase to sine amplitude, the ROM-less Direct Digital Frequency Synthesizer (DDFS) consumes less power than the conventional ROM lookup table approach. To further reduce the power dissipation and the die area of the sine wave DAC, two segmented sine wave DAC architectures are proposed in this paper. The optimized segmentation parameters for better performance and lower power dissipation are also discussed.

Direct digital frequency synthesis (DDS) as an indispensable key technology for modern communication systems, is widely used in digital communications, satellite communications, aerospace and high-speed instrumentation. In practical applications, DDS technology is usually required to generate different kinds of communication signals. In view of the fact that there is no related research on spurious signals when DDS technology generates communication signals, this paper based on a DDS model that can generate arbitrary symbol rate communication signals, analyzes spurious signals of the structure in detail. The conclusions of this paper can be used for the spur evaluation and parameter selection in DDS engineering applications. At the same time, this paper provides a theoretical basis for the low spurious design of DDS, and has certain reference value for DDS to generate communication signals.

A ROM-less direct digital frequency synthesizer employing trigonometric quadruple angle formula is present in this paper. The worse case spectral purity is better than -130 dBc. The amplitude resolution is up to 13 bits, while the phase resolution is 12 bits. Neither any scaling table nor error correction tables are required. The maximum error is mathematically analyzed. The word length of each multiplier is carefully selected in the digital implementation such that the error range is circumscribed and the resolution is preserved.

This paper presents an ultra-high-speed direct digital frequency synthesizer (DDS) microwave monolithic integrated circuit (MMIC) implemented in 1μm GaAs HBT technology. The DDS has the capabilities of direct frequency modulations with 8-bit frequency resolutions. Utilizing a Double-Edge-Trigger (DET) 8-stage pipeline accumulator with sine-weighted DAC based ROM-less architecture, this DDS MMIC can maximize the utilization ratio of GaAs HBT's high-speed potential. With an external clock output frequency of 5GHz, the DDS can output sine signal of up to 5GHz frequency giving an average Spurious Free Dynamic Range (SFDR) of 23.24dBc through the first Nyquist band. The DDS MMIC consumes 2.4W of DC power from a single -4.6V DC supply. Using 1651 GaAs HBT transistors, the total area of the DDS chip is 2.4 × 2.0mm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> .

An 800 MSPS quadrature Direct Digital Frequency Synthesizer (DDFS) with an integrated 13-bit nonlinear DAC and a 200 MHz spur-rejection filter is presented. The system consists of a 10 ns latency ROM-less DDFS and a sine-weighted, current-steering DAC with a layout technique conducive to the DDFS algorithm. A 200 MHz active OTA-RC spur-rejection filter follows the DDFS-DAC giving > 60 dB rejection at 600 MHz with an IIP3 of 25 dBm. The system achieves an SFDR ≈ 33 dB and a total instantaneous hopping time of 15 ns. The system is designed and fabricated in a 0.13 μm CMOS technology, has a total chip area of 2.54 mm × 2.96 mm, and consumes 420 mW of power.

In this paper, we analyze the design and the possible optimization methods of the direct digital frequency synthesizer (DDFS) based on quadratic approximation. The goal is to design a DDFS with reduced hardware cost and very high spectral purity. For the DDFS based on quadratic approximation, there is a trade-off between the size of the memory and the approximation logic. We show that by exploring this trade-off, it is possible to design a DDFS which requires less hardware and features higher spectral purity than the previously presented solutions. By using the proposed design method, a DDFS that generates 16-bit sinusoidal waves with a spurious free dynamic range of 132 dBc (126 dBc if the phase is truncated) was designed.

An experimental platform was developed to investigate the effects of audible sound (20 Hz to 20 MHz) on plant growth promotion, which included a microcontroller-based embedded system for audible sound adjustment and analysis. The direct digital frequency synthesis (DDFS) method was used to generate various waveforms of sound in the platform. Soundproof glass and mufflers were used to reduce background noise. The developed system was tested on various plants, including hydroponic tomatoes, celery and mung bean. The testing results showed that the developed platform could produce pure tone and mixing audible sound with high stability and accuracy, make octave analysis of the sound under experimental environments, and the background noise in the testing chamber of the platform was lower than 55 dB(A) when the compression engine was working. The developed experimental platform has a great potential on facilitating scientific research on acoustic biology effects on plants and collecting real-time experimental data. Keywords: plant growth, background noise, acoustic biology effect, direct digital frequency synthesis, sound sensor DOI: 10.3965/j.ijabe.20150805.1556 Citation: Cai W M, Zhu S M, Wang N, He H N, Ying B H. Design of an experimental platform to investigate the effects of audible sounds on plant growth. Int J Agric & Biol Eng, 2015; 8(5): 162－169.

This paper introduces a novel Direct Digital Frequency Synthesizer (DDFS) based on Complementary Dual-Phase Latch-Based digital design. Compared to conventional DDFS using Flip-Flop as synchronizing element, the proposed approach allows to double the sampling data rate while enhancing the clock skew tolerance and system latency. The design features a 24 bits pipelined Phase Accumulator (PA) and a 14×10 bits Phase to Amplitude Converter (PAC). The Phase to Amplitude Converter module is compressed using Quarter Wave Symmetry technique and is entirely made up of combinational logic inserted into 12 Complementary Dual-Phase Latch-Based pipeline stages. The logic is represented in the form of Sum of Product (SoP) terms obtained from a 14×10 bits sinusoidal Look-Up-Table. The proposed DDFS is designed and simulated based on TSMC 65nm CMOS standard-cell technology. A maximum data sampling rate of 6.8 GS/s and 0.022 W/ GS/s Power Efficiency (PE) is expected.

Direct Digital Frequency Synthesizer (DDFS) has long been perceived as a predominant solution for producing precise, variable frequency signals having very low distortion. The paper presents an epigrammatic and a comparative study of direct digital frequency synthesizers architectures. The direct digital frequency synthesizer presented are compared on the basis of two architectures namely, the read only memory (ROM) or look up table based architecture and the other co-ordinate rotation based digital computer that eliminates the usage of the large ROM based look up table. These architectures are compared in terms of the power utilization, SFDR, etc. A mixed signal ASIC designing approach is followed for the implementation approach.

This work presents a low power direct digital frequency synthesizer (DDFS) by using a new two-level lookup table algorithm. The algorithm uses trigonometric double angle formula to divide ROM lookup table into two parts. The ROM size of the proposed architecture is 25% less than that of conventional two-level table. The hardware complexity of the new DDFS architecture compared to the traditional two-level table DDFS can be omitted one multiplier. A synthesized 0.35-mu DDFS with a SFDR of -80dB, runs up to 100MHz and consumes 81-mW at 3.0v. The power efficiency is 0.81-mW/MHz, which represents an enhancement of more than 38% compared to the conventional DDFS

In order to test the working state of adaptive optics system, it is necessary to design an online sweep-frequency circuit module to test the frequency response of the adaptive system. Sweep-frequency signal generator based on Direct Digital frequency Synthesis (DDS) is one of the core components. But the classic DDS technology also has some drawbacks: the truncation error of phase, the truncation error of magnitude (caused by memory FWL) and high occupancy of ROM. These are also the optimization directions in this paper. This paper presents a FPGA-based DDS sweep-frequency signal generator suitable in adaptive optics. It has a low occupancy rate with ROM. And in the case of low-ROM, the paper reduces the noise generated by the truncation error of phase and the truncation error of magnitude of DDS sweepfrequency signal generator by method of linear interpolation. The results show that, when the reference frequency is 100 MHz, the frequency resolution can be as low as 0.025 Hz. It only takes up 0.5 KB ROM with the ROM compression ratio of 64:1 in the optimized scheme in the paper and has higher precision due to the method of linear interpolation than the unoptimized scheme, which can meet the engineering needs. Compared with other schemes, the scheme in the paper improves signal accuracy in the case of reducing the truncation error of phase, the truncation error of magnitude and the occupancy rate with ROM, but only adds a multiplication and division circuit, which is a practical solution.

A quadrature direct digital frequency synthesizer (DDFS) was designed and implemented in a 1.2 µm CMOS process using two non-linear resistor string DACs. These DACs are used in place of the phase-to-amplitude ROM look-up tables and the linear DACs in a conventional quadrature DDFS to give a low power design. At 25 MHz clock frequency, the DDFS dissipates less than 4 mW at 3.3 V and has SFDR better than 55 dBc at low synthesized frequencies.