Low Temperature Drift Bandgap Reference Based on Parabolic Current Correction Architecture

This paper presents a high wide band power supply rejection ratio (PSRR) current mode bandgap reference (BGR) with a fast startup performance. The BGR includes three main enhancement techniques to improve the PSRR. The proposed design is implemented in 130nm CMOS technology. It only consumes 50μA from a 1.8V supply. The BGR provides 850mV reference voltage and has a power supply rejection ratio (PSRR) of 130dB from DC to 100Hz and more than 110dB till 100MHz. The temperature coefficient (TC) is 10 ppm/°C from -40°C to 125° C. The Bandgap start-up time is 70ns.

Ultra-low-power (ULP) sensor technologies for the future internet of things have presented challenges in ULP implementation of reference circuits while keeping traditional requirements of stable performance. For voltage reference circuits, as an essential block in SoCs to generate various internal supply voltages, the bandgap voltage-reference (BGVR) scheme has been widely used since it provides a well-defined value with strong immunity to process/voltage/temperature variations. Nanowatt-consuming BGVR circuits have been recently proposed using a capacitor network [4] and a leakage-based proportional-to-absolute-temperature (PTAT) circuit [5]. On the other hand, the current reference circuit that is required to set internal bias current still presents difficulties in achieving both stable performance and ULP consumption. The general approach to building a current reference is to use a BGVR with additional resistors for V-to-I conversion. Though it can provide a well-defined stable current reference, it also requires excessively large resistance for ULP consumption. Another approach is a CMOS-based current reference circuit that tries to make the exponential term in the subthreshold current equation constant or temperature-independent, hence reducing process and temperature dependencies. While CMOS reference circuits have achieved ULP implementations, the current is still determined by a number of process and design parameters, resulting in large sensitivity to process variations. This paper presents a sub-10nW bandgap-reference (BGR) circuit that implements both voltage and current references in one circuit. The BGR circuit is implemented with a 0.18µm CMOS process and generates voltage and a current references of 1.238V and 6.64nA while consuming 9.3nW. The voltage and current references show standard deviations of 0.43% and 1.19% with temperature coefficients of 26ppm/°C and 283ppm/°C, respectively.

This brief presents a low-noise, low-offset bandgap reference for the biomedical electronic systems application. In order to reduce the low-frequency noise and increase the accuracy, the low-frequency noise/offset elimination technique based on current-mode bandgap reference (BGR) is proposed. Besides, this BGR utilizes a proportional to absolute temperature (PTAT) resistor feedback technique to minimize the low-frequency noise and offset from the current mirror. The proposed BGR is implemented in a 180 nm deep n-well CMOS process occupying an active area of 0.0725 mm2. The measured results indicate that the BGR outputs 0.6 V voltage and consumes 69 μA current under 1.2 V supply voltage. It can achieve 3.5 μV(rms) noise from 0.1 to 10 Hz and a 0.21% DC accuracy.

A novel 79-nW CMOS-only subthreshold voltage reference with 328-mV output voltage, which works down to 0.8-V supply voltage, is presented in this brief. In order to reduce the area and power consumption, the proposed circuit avoids the use of resistors and bipolar transistors. A current subtracting technique is proposed to realize the temperature compensation of reference current. Instead of the op-amp in traditional circuits, some cascode current mirrors are used to enhance the power supply rejection ratio (PSRR). A novel structure consisting of a 1.8-V MOS transistor and a 3.3-V MOS transistor is utilized to accomplish the voltage temperature compensation and to further reduce the power consumption of VREF generator. The proposed voltage reference was fabricated in 0.18- ${\mu }\text{m}$ CMOS process. The measured results show that the temperature coefficient of the output voltage is 33.8 ppm/°C in the range from 10 °C to 100 °C, the PSRR is −55 dB @ 100 Hz at 1.2-V power supply, and the line regulation is 0.21%/V in a supply voltage range of 0.8 to 3.4 V. What is more, the power dissipation is 79 nW, and the chip area is 0.01 mm2. It is suitable for low-power applications.

A novel current reference with low temperature and supply sensitivity and without any external component has been developed in a 0.25 /spl mu/m mixed-mode process. The circuit is based on a bandgap reference (BGR) voltage and a CMOS circuit similar to a beta multiplier. An NMOS transistor in triode region has been used in place of a resistor in conventional beta multiplier to achieve a current which has a negative temperature coefficient and only oxide thickness dependent. The BGR voltage has a positive temperature coefficient to cancel the negative temperature coefficient of the beta multiplier. The simulation results using Bsim3v3 model show max-to-min fluctuation of less than 1% over a temperature range of -20/spl deg/C to +100/spl deg/C and a supply voltage range of 1.4 V to 3 V with /spl plusmn/30% tolerance for all of the used on- chip resistors. The maximum current variation is slightly less than the oxide thickness variation in the process corners.

In this paper, A precision bandgap reference (BGR) with high power supply rejection ratio (PSRR) and low-temperature coefficient (TC) is designed. It comprises a bandgap reference core circuit, a negative feedback loop, a nonlinear temperature compensation circuit, and a bias circuit. The bias circuit is used to increase the PSRR, a negative feedback loop is introduced to maintain the constant output reference voltage, and a nonlinear compensation circuit is used to increase the temperature drift coefficient of the bandgap reference. The voltage supply is 3. 3V. This simulation is based on the SMIC 0.1S$\mu$m CMOS process. The results show that the temperature drift coefficient of the bandgap reference source is 3.255ppm/°C in the temperature range of −40°C~130°C. The PSRR is 103. 192dB at the frequency of 1Hz. The power consumption is 13.1996$\mu$W. The offset voltage is 2.15591mV by Monte Carlo simulation.

This paper presents a high-precision, low temperature coefficient (TC) CMOS bandgap reference for high-performance multi-channel ADC working under wide temperature range. A piecewise curvature compensation technique is proposed to extend its operating temperature range and keep its low temperature coefficient. A s-compensation technique is used to cancel the PTAT and non-PTAT spread of the output due to variation of β in the BJTs. Moreover, the trimming resistors are implemented to calibrate the 1st-order temperature coefficient and absolute value of the output voltage. The bandgap reference designed in 0.18μm CMOS process has a super low temperature coefficient of 2.1ppm/°C over a wide temperature of −55 ° C to 140 ° C, making it appropriate to provide reference voltage for a high-precision ADC.

A novel bandgap reference (BGR) with low temperature and supply voltage sensitivity without any resistor, which is compatible with standard CMOS process, is presented in this article. The proposed BGR utilises a differential amplifier with an offset voltage proportional to absolute temperature to compensate the temperature drift of emitter–base voltage. Besides, a self-biased current source with feedback is used to provide the bias current of the BGR core for reducing current mirror errors dependent on supply voltage and temperature further. Verification results of the proposed BGR implemented with 0.35 µm CMOS process demonstrate that a temperature coefficient of 10.2 ppm/°C is realised with temperature ranging from −40°C to 140°C, and a power supply rejection ratio of 58 dB is achieved with a maximum supply current of 27 µA. The active area of the presented BGR is 160 × 140 µm2.

High-precision microelectromechanical system (MEMS) gyroscopes are significant in many applications. Bias instability (BI) is an important parameter that indicates the performance of a MEMS gyroscope and is affected by the 1/f noise of the MEMS resonator and readout circuit. Since the bandgap reference (BGR) is an important block in the readout circuit, reducing its 1/f noise is key to improving a gyroscope’s BI. In a traditional BGR, the error amplifier is applied to provide a virtual short-circuit point, but it introduces the main low-frequency noise sources. This paper proposes an ultralow 1/f noise BGR by removing the error amplifier and applying an optimized circuit topology. In addition, a simplified but accurate noise model of the proposed BGR is obtained to optimize the BGR’s output noise performance. To verify this design, the proposed BGR has been implemented in a 180 nm CMOS process with a chip area of 545 × 423 μm. The experimental results show that the BGR’s output integrated noise from 0.1 to 10 Hz is 0.82 μV and the thermal noise is 35 nV/√Hz. Furthermore, bias stability tests of the MEMS gyroscope fabricated in our laboratory with the proposed BGR and some commercial BGRs are carried out. Statistical results show that reducing the BGR’s 1/f noise can nearly linearly improve the gyroscope’s BI.

The accelerated aging stress test is essential for assessing the reliability and quality of band gap reference (BGR) circuits, which are crucial for maintaining consistent voltage references in ICs. In this study, we present accelerated aging analysis of a classic BGR design as an case study. A BGR circuit, validated on a Quality and Reliability On-Chip (QROC) platform, demonstrated temperature coefficient of <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$0.12 \text{ mV} /{}^{\circ} \mathrm{C}$</tex> across 25° C to 100° C, ensuring minimal drift with temperature fluctuations. The output reference voltage <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$(V_{{ref}}) 646$</tex> mV was measured over a supply voltage range of 0.8V to 1.4V, with a <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$\pm 7.5 \text{ppm} / \mathrm{V}$</tex>. The circuit's robustness was further confirmed by observing only a 1% change in <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$V_{{ref}}$</tex> after a million-second stress test at varying temperatures and a stress voltage 1.4V. This result, showing less than 6.5% deviation from post-layout simulations, underscores the BGR's resilience and precision, highlighting the importance of such stress testing in predicting IC performance and longevity.

A new PVT compensated voltage reference is presented by using switched-capacitor (S.C.) technique. In the proposed bandgap voltage reference (BGR), a p–n junction is biased with different currents during two different phases and required PTAT and CTAT voltages generated and held by two capacitors. Using a capacitive voltage divider, the PTAT voltage is weighted such that the sub-1V bandgap voltage is achievable. In order to cancel the effect of op-amp offset and to relax the design of op-amp, the offset voltage of the op-amp is sampled by a capacitor during a specified phase and inversely is added to the final bandgap voltage in next phase. The analysis of the proposed S.C. BGR is supplemented by simulation of a 0.5-V BGR with 28[Formula: see text][Formula: see text][Formula: see text]W power consumption in a standard 0.18[Formula: see text][Formula: see text][Formula: see text]m CMOS technology. Simulation results show that the average temperature coefficient of the S.C. BGR is 17[Formula: see text]ppm/∘C and it is robust against the process variations. Applying an arbitrary 100-mV op-amp offset results in a lower than 1.1[Formula: see text]mV deviation in generated reference voltage. Due to the better matching of MIM capacitors in CMOS process (rather than resistors used in conventional BGR) the proposed S.C. bandgap provides good accuracy without any post trimming. Monte–Carlo analysis shows that [Formula: see text]/[Formula: see text] of the generated reference voltage is as low as 0.7%. The sensitivity of the proposed BGR to supply variation is also less than 1%/V.

ABSTRACTA bulk-isolated curvature-compensated bandgap voltage reference (BGR) compatible with triple-well CMOS technologies is presented in this paper. Verification results of the proposed BGR implemented in a 0.35-µm 3.3-V triple-well CMOS technology demonstrate that the BGR achieves a reference voltage of 220.4 mV with an average temperature coefficient (TC) of 3.7 ppm/°C in the −40 to 130°C range with 8-bit trimming. The measured current consumption and power supply rejection of the circuit are 33.15 µA and −69.51 dB at 100 Hz, respectively (VDD = 3.3 V). The circuit is capable of operating with supply voltages down to 2 V and its line regulation is 0.16%/V over a voltage range from 2 to 3.6 V. The root mean square output noise voltage in the 0.1–10 Hz frequency range is 2.54 µV. Moreover, measurement results show that the substrate noise sensitivity at the BGR output improved more than 30 dB for frequencies up to 50 kHz, thanks to the employed block bulk isolation strategy, although the effective improvement is expected to be more than 75 dB without the coupling from the electrostatic discharge diode in the I/O pad.

Novel high-PSRR high-order curvature-compensated bandgap voltage reference

A high-precision current-mode bandgap reference (BGR) circuit with a high-order temperature compensation is presented in this paper. In order to achieve a high-precision BGR circuit, the equation of the nonlinear current has been modified and the high-order term of the current flowing into the nonlinear compensation bipolar junction transistor (NLCBJT) is compensated further. According to the modified equation, two solutions are designed to improve the output accuracy of BGR circuits. The first solution is to divide the NLCBJT branch into two branches to reduce the coefficient of the nonlinear temperature compensation current. The second solution is to inject the nonlinear current into the two branches based on the first one to further eliminate the temperature coefficient (TC) of the current flowing into the NLCBJT. The proposed BGR circuit has been designed using the Semiconductor Manufacturing International Corporation (SMIC) 55 nm CMOS process. The simulation results show that the variations in currents flowing into NLCBJTs improved from 148.41 nA to 69.35 nA and 7.4 nA, respectively, the TC of the output reference current of the proposed circuit is approximately 3.78 ppm/°C at a temperature range of -50 °C to 120 °C with a supply voltage of 3.3 V, the quiescent current consumption of the entire BGR circuit is 42.13 μA, and the size of the BGR layout is 0.044 mm2, leading to the development of a high-precision BGR circuit.

In this paper, a novel CMOS bandgap reference (BGR) with high-order curvature compensation by employing only a MOS transistor operating in strong-inversion deep-triode region is proposed. The mechanism of the compensation technique is analyzed in detail and the BGR is designed in standard 65-nm CMOS process. The simulation results show that the presented BGR achieves a temperature coefficient (TC) of 9.8 ppm/°C over the temperature range of -20°C to 150°C at 2.5V supply voltage. And a high precision reference voltage of 1.2V is obtained under room temperature (27°C). The line regulation is 0.33%/V in the supply voltage ranging from 1.8 to 3.6V. Comparing with the conventional circuit, the proposed architecture improves the accuracy over temperature and saves the chip area effectively.