Self-Aligned Double Patterning Lithography Aware Detailed Routing With Color Preassignment

Double patterning lithography (DPL) is the most likely manufacturing process for sub-32nm technology nodes; however, there are several double patterning strategies each of which exhibits different layout decomposition challenges. Self-aligned double patterning (SADP) has attracted much interest due to its robustness against overlay errors, but SADP compliance depends strongly on the characteristics of the individual masks generated during the layout decomposition. This work establishes SADP decomposition requirements and proposes a litho-friendly layout decomposition method. First, we explain the main parameters that limit printability of SADP decomposed layouts. In-silico experiments indicate that layout patterns which are printed by the Trim mask may experience the highest levels of image transfer sensitivity. For that reason, these patterns should be assisted by sidewalls of spacer patterns which are robustly printed. Next, we present an ILP-based decomposition method which avoids decomposition conflicts and sensitive Trim edges simultaneously. Our experiments on several industrial designs reveal that the proposed method decreases the total length of sensitive Trim patterns and consequently reduces the overall edge placement error significantly.

Self-aligned double patterning (SADP) is being applied to 7nm technology node and below for back-end metal layers (routing layers) with pitches down to ~40nm. Unlike the traditional litho-etch-litho-etch (LELE) approach, SADP splits pitch using spacers whose 2nd pattern (Color-B) is self-aligned to its 1st pattern (Color-A). As a result, the SADP approach produces less variation than LELE approach by removing the second pattern misalignment on Si. Although SADP provides better overlay controllability than LELE, it still encounters many challenges. One of the challenges is controlling the 2nd patterning linewidth and uniformity. In general, the Color-B critical dimension (CD) has a larger variation than Color-A CD in the SADP process using Mandrel structure. In this paper, we investigate variations to the SADP Color-B CD based on self-aligned litho-etch litho-etch (SALELE) process flow, including the lithographic CD uniformity, hard mask etching, spacer etch and final Si etch. The corresponding contribution to Color-B CD variation is analyzed each step. After the major contributors to Color-B variation are identified, an experiment was designed to reduce Color-B pattern variation during the process. The silicon results show that compared with the old process condition, the new process can reduce Color-B variation significantly. With this new process, Color-B variation is comparable to Color-A variation.

Amongst the possible double patterning strategies for sub 32nm processes, self-aligned double patterning (SADP) has moved from Flash-only processes to more general purpose devices. The reason is that while litho-etch- litho-etc (LELE) process was originally preferred due to its simplicity and relative low cost, its sensitivity to overlay error has prompted the search for other methods. Although the basic SADP process is fairly robust against the overlay error, the robustness of 2D SADP method strongly depends on layout and decomposition styles and decomposability compliance. In this paper, we first discuss different printability challenges for SADP method. Afterward, we propose a SADP-aware detailed routing method, by applying a correct-by-construction approach, to provide SADP-friendly layouts. This method performs detailed routing and layout decomposition concurrently to prevent litho-limited layout configurations. Experimental results show that, compared with a SADP-blind detailed router, the proposed method achieves considerable robustness against lithography imperfection in expense of tolerable wire length overhead.

Among double patterning techniques, Self-aligned double patterning (SADP) has the advantage of good mask overlay control, which has made SADP a popular double patterning method for sub-32nm technology nodes. However, SADP process places several limitations on design flexibility. This work exploits an alternative post routing approach that has the flexibility to resolve lithography violations without the overhead of repeated rule checking. In addition, it allows for successive refinement in the definition of lithographic violations as the process node matures, and implementation of fixes as localized ECO (Engineering Change Order) operations without needing to reroute the complete design.

Lithographic scaling has been driven by improvements in wavelength and numerical aperture historically. In the semiconductor industry, the H2O base 192 immersion technique has still been main exposure tool combined with various low-k1 techniques, such like off-axis illumination, phase-shift mask and so on. The focus is now on double patterning techniques (DPT) as a means to circumvent the limitations of Rayleigh′s definition. Actually, self-aligned spacer double patterning (SADP) has already been employed in high volume manufacturing of NAND flash memory devices. This paper introduces demonstration results focused on the extendibility of double patterning techniques for downward scaling and various device layouts utilizing SADP (Self-aligned Double patterning) mainly.

Self-aligned double patterning (SADP) is one of the most promising techniques for sub-20 nm technology. Spacer-is-dielectric SADP using a cut process is getting popular because of its higher design flexibility; for example, it can decompose odd cycles without the need of inserting any stitch. This paper presents the first work that applies the cut process for decomposing odd cycles during routing. For SADP, further, overlay control is a critical issue for yield improvement; while published routers can handle only partial overlay scenarios, this paper identifies all the scenarios that induce overlays and proposes a novel constraint graph to model all overlays. With the developed techniques, our router can achieve high-quality routing results with significantly fewer overlays (and thus better yields). Compared with three state-of-the-art studies, our algorithm can achieve the best quality and efficiency, with zero cut conflicts, smallest overlay length, highest routability, and fastest running time.

With extreme UV not ready for HVM for the 20nm and 14nm nodes, double patterning options that extend the use of 193nm immersion lithography beyond the optical resolution limits, such as LELE (Litho-Etch-Litho-Etch) and SADP (Self Aligned Double Patterning), are being used for critical layers for these nodes. LELE requires very stringent overlay capability of the optical exposure tool. The spacer scheme of SADP starts with a conformal film of material around the mandrels and etched along the mandrel sidewalls to form patterns with doubled frequency. SADP, while having the advantage of being a self-aligned process, adds a number of process steps and strict control of the mandrel profile is required. In this paper, we will demonstrate a novel technique - ASDP (Anti-Spacer Double Patterning), which uses only spin-on materials to achieve self-aligned double patterning. After initial resist patterning, an Anti-Spacer Generator (ASG) material is coated on the resist pattern to create the developable spacer region. Another layer of material is then coated and processed to generate the second pattern in between the first resist pattern. We were able to define 37.5nm half pitch pattern features using this technique as well as sub-resolution features for an asymmetric pattern. In this paper we will review the capability of the process in terms of CD control and LWR (line width roughness) and discuss the limitations of the process.

Overlay performance has been a critical factor for advanced semiconductor manufacturing for years. Over time these requirements become more stringent as design rules shrink. Overlay mark design and selection are the first two steps of overlay control, and it is known that different overlay mark designs will have different responses to process conditions. An overlay mark optimized for traditional process might not be suitable for SADP (self-aligned double patterning) technology due to changes in lithography and etching process conditions. For instance, the traditional BIB (box-in-box) target defined by the core mask becomes a template structure in SADP flow, the pitch and cycle of the overlay mark is further changed after spacer formation and core film removal hence the mark recognition and robustness have been challenging for the subsequent process layers. The comprehensive study on the methodology of overlay mark design and selection is still not available for SADP process. In this paper, various types of overlay marks were designed to comply with the SADP process to get rid of the weaknesses of traditional targets. TMU (total measurement uncertainty) performance was adopted to determine the optimal overlay marks for meeting production overlay control requirements in SADP process flow. The results have suggested the segmented marks outperform to non-segmented marks on image contrast as well as TMU.

Self-Aligned-Double-Patterning (SADP) is a potential technology for metal layers in N10 and beyond nodes. SADP manufacturing process comes with lots of challenges. Several approaches were introduced to manufacture SADP. The most major SADP manufacturing approach is the Spacer-Is-Dielectric (SID). One of the main advantages of SADP over Litho-Etch-Litho-Etch (LELE) Double Patterning (DP) is better Mask Overlay Control. In addition, SADP results in better process tolerance and lower Line-Width Roughness. In this paper, we propose a model-based manufacturing flow for SID-SADP approach. The flow includes: (1) SADP Patterns Decomposition, (2) Etch Retargeting, (3) Sub Resolution Assist Features (SRAF) Insertion, (4) Optical Proximity Correction (OPC) process, and finally (5) Verification. The motivation beyond developing this flow is to find the least number of needed masks to achieve satisfactory imaging quality, and to characterize possible challenges in each step of the flow. Consequently, we highlight the challenges and the proposed techniques we examined to meet this objective.

Manufacturing has been incapable of keeping up with Moore's law without significantly increasing process variability and imposing massive geometric restrictions on design. This paper highlights the design impact of variability and geometric constraints - including traditional design rules and pattern-scale constraints - and describes our approach for evaluating and enforcing pattern-scale restrictions on design.

EUV is an ongoing industry challenge to adopt due to its current throughput limitations. The approach to improve throughput has primarily been through a significant focus on source power which has been a continuing challenge for the industry. The subject of this paper is to review and investigate the application of SADP (Self aligned double patterning) as a speed enhancing technique for EUV processing. A process with the potential of running a 16 nm self-aligned final etched pattern in less than 10mJ exposure range is proposed. Many of the current challenges with shot noise and resolution change significantly when SADP is used in conjunction with EUV. In particular, the resolution challenge for a 16nm HP final pattern type image changes to 32nm as an initial pattern requirement for the patterned CD. With this larger CD starting point, the burden of shot noise changes significantly and the ability for higher speed resist formulations to be used is enabled. Further resist candidates that may have not met the resolution requirements for EUV can also be evaluated. This implies a completely different operational set-point for EUV resist chemistry where the relaxation of both LER and CD together combined, give the resist formulation space a new target when EUV is used as a SADP tool. Post processing mitigation of LWR is needed to attain the performance of the final 16nm half pitch target pattern to align with the industry needs. If the original process flow at an 85W projected source power would run in the 50WPH range, then the flow proposed here would run in the <120WPH range. Although it is a double patterning technology, the proposed process still only requires a single pass through the EUV tool, This speed benefit can be used to offset the added costs associated with the double patterning process. This flow can then be shown to be an enabling approach for many EUV applications.

As integrated circuit technology nodes continue to shrink, dense via distribution becomes a severe challenge, requiring multiple masks to avoid spacing violations in via layers. Meanwhile, the directed self-assembly (DSA) technique shows a great promise in via printing by employing feasible guiding templates. Combining DSA with double patterning lithography can significantly reduce the number of masks for via layers. In this paper, we propose a detailed routing algorithm considering DSA with DPL based on a conflict and compatibility graph model. A net planning algorithm is developed to reduce via-dense areas and determines a prerouting nets order, while the graph model is employed to capture the feature of DSA and DPL to better guide detailed routing. Besides, DSA grouping is performed for critical vias during detailed routing to avoid attracting more vias inserted in surrounding grids to reduce via-spacing violations. Experimental results demonstrate that our routing algorithm can effectively minimize the number of via spacing violations, with an even smaller total via count.

As EUV direct patterning begins to hit its resolution limit, the need for EUV self-aligned double patterning (SADP) has arisen in order to reach sub-30 nm pitch. Currently, EUV resists suffer from several shortcomings, both in terms of roughness and resist budget. These constraints means using it directly as a mandrel material, as previously done for immersion lithography SADP is nearly impossible. Consequently, standard EUV SADP flows involve the transfer of the resist through a lithography stack and into a hard mandrel material, such as silicon nitride or amorphous silicon.¹ Achieving line edge roughness (LER) and line width roughness (LWR) targets for an EUV SADP hard mandrel is significantly more challenging than for EUV direct print since the etch process needs to target a post etch CD of about half that of the lithographic CD. This aggressive shrink requirement usually involves degradation in roughness driven by high aspect ratios. To circumvent these issues, we have developed a new bottom up organic mandrel growth process, whereby the EUV resist can be grown to a height compatible with a resist mandrel SADP flow, while the roughness is improved and the critical dimension is controlled. This bottom up mandrel growth process is performed in an etch chamber and can therefore be easily coupled with other process steps. The mandrel height and critical dimensions can be easily tuned from the incoming lithography by changing the deposition and trim step times of the process. We have shown that this bottom-up grown mandrel can withstand typical ALD spacer process deposition. After spacer open, the organic material can be easily removed through an in-situ ash process before opening the underlayer. This integration will allow for the removal of the organic planarizing layer in the lithography stack, reducing the stack complexity, while also eliminating one of the major contributors to wiggling in the typical hard mandrel patterning scheme. In this paper, the performance of this new integration scheme was benchmarked against a more standard SADP flow. The roughness performance post mandrel formation and post spacer deposition for this new scheme is significantly improved over our standard EUV SADP baseline using a standard EUV SADP flow.

We report a sub-30-nm pitch self-aligned double patterning (SADP) integration scheme with EUV lithography coupled with self-aligned block technology targeting the back end of line metal line patterning applications for logic nodes beyond 5 nm. The integration demonstration is a validation of the scalability of a previously reported flow, which used 193-nm immersion SADP targeting a 40-nm pitch with the same material sets (Si3N4 mandrel, SiO2 spacer, spin on carbon, spin on glass). The multicolor integration approach is successfully demonstrated and provides a valuable method to address overlay concerns and, more generally, edge placement error as a whole for advanced process nodes. Unbiased line edge roughness (LER)/line width roughness (LWR) analysis comparison between EUV SADP and 193-nm immersion SADP shows that both integrations follow the same trend throughout the process steps. While EUV SADP shows increased LER after mandrel pull, metal hardmask open, and dielectric etch compared to 193-nm immersion SADP, the final process performance is matched in terms of LWR (1.08-nm 3 sigma unbiased) and is 6% higher than 193-nm immersion SADP for average unbiased LER. Using EUV, SADP enables almost doubling the line density while keeping most of the remaining processes and films unchanged and provides a compelling alternative to other multipatterning integrations, which present their own sets of challenges.

Design shrinking beyond the resolution limits of 193 nm optical lithography requires the introduction of double patterning technology (DPT) for the semiconductor industry. Two consecutive lithography and etching process (LELE; Litho-Etch-Litho-Etch) and self aligned double patterning (SADP) process are major two options of DPT.In LELE process, layout patterns are decomposed into two groups and each group is placed on a photo mask. The original layout is reconstructed on a wafer through two lithography with two those photo masks. The two lithography processes are independent because of the intermediate process in between, such as etching and resist freeze. Lithography conditions for each mask are optimized on source mask optimization (SMO) technique to enlarge lithography margin. Conventional SMO technique can be applied to the decomposed patterns since two lithography processes have no interaction as discussed above.In SADP process, a layout is also decomposed into two groups as same as the methodology for LELE process. Either decomposed group is transferred on a wafer, which is named as mandrel. Sidewalls are deposited on the mandrel patterns and the following processes such as etching and mandrel removal reconstruct the original layout.Design rules for DPT consist of two parts. One is for an original layout which is drawn by designers. The other is for each decomposed layout printed by a lithography process. Both design rules have interactions because the original layout which follows the former design rules is decomposed into two groups which follow the latter design rules.In this paper, we will discuss the relation between the two rules above. Furthermore, we will discuss the situation on triple or quadruple patterning.